Share your ROUTE Experience

Plz send latest dumps for rote exam. begamganj@gmail.com

Thank you.

@ ccnp, yes YOU!

The one WHO posted the questions and expected people to spoon-feed you.
GO BACK TO CCNA!!!

YOU NEED TO GRASP THE BASICS BEFORE YOU COME TO THIS FORUM.
YOU ARE A DISGRACE !!!

@all

this config for lab pbr lab is correct or not ?then how to test this lab ?

BorderRouter#access-list 101 permit tcp any any eq www
BorderRouter(config)#route-map pbr permit 10
BorderRouter(config-route-map)#match ip address 101
BorderRouter(config-route-map)#set ip next-hop 10.1.101.1
BorderRouter(config-route-map)#exit
BorderRouter(config)#route-map pbr permit 20
BorderRouter(config-route-map)#exit
BorderRouter(config)#int fa0/0
BorderRouter(config-if)#ip policy route-map pbr
BorderRouter(config-if)#exit
BorderRouter(config)#exit

please reply

@ bishoy
its correct
there is a “Host for testing” in real exam at EIGRP network click on that host then you find button named “Generate HTTP traffic” click on this button to generate HTTP traffic then go to BorderRouter and type the command
“show route-map”______>in the output you will see the line “policy routing matches:9 packets it means that the route-map is working.

In Exam lab help command (?) can work or not please tell.

hi all,

Just a word to tell you that today I was playin with GNS3 replicating cbtnuggets labs.
I was working on OSPF NBMA config lab and I figured how to configure a router to be a frame relay switch :)

That was really instructive, and I would like to encourage all of you to go further and deeper than the simple labs give on the route exam.

Wish you all good luck and hae fun

@ all
in ipv6 ospf lab why when use ping ipv6 fec0:4::4 command not reply ?

@Bishoy

You need to issue the command
Router#ping ipv6 FEC0:4::4

@Bishoy

I did the “config for lab pbr lab” on GNS3 & the only issue I had was with the first line;
should be in configuration mode for access-list 101 permit tcp any any eq www statement.

BorderRouter#access-list 101 permit tcp any any eq www

Should be;

BorderRouter(Config)#access-list 101 permit tcp any any eq www

@ Bishoy

Check R1 and make sure R1′s loopback interface is running in OSPF.

Is the ” #distance eigrp 90 105 ” command mandatory to use in the redistribution lab on the exam?

Passed exam today.

The sims were PBR, Redistribut, Virtual link and OSPF.

I studied from actualtest 6.2 and p4s 338q all the questions came from there.

Dont forget the distance eigrp 90 105, is mandatory

Hi all
thanks for your great post very appreciated

I cleared my ccna last year and i would like to jump now with the ccnp route.
So may I use packet tracer 5.3? does any one use packet tracer to preapare the ccnp???
Thanks for your kind feed back

@Mike Thanx For suggestion

any one has idea about drag and drop questions in exam. please share the link to down load

Hi pals,i’m planning to sit for the Route exam in the next 2wks,i have gone through all the notes & i’m wondering which are the best dumps to use for revision.Anyone who has sat for the exam in the near past who can advise??A link to download them would also be highly appreciated.

From Examcollection..can anyone tell me what is the latest valid dumb…

Thanks

I had taken the exam on 26th, there are 50 questions 4 LABs, 3 D&D labs are same but little change in the OSPF you have to create the areas except that the dumps entitiy & P4S are valid but sequence are abrupt.

By grace of god i cleared though score was not good, but thanks all, specially digitaltut.

With this i am a CCDP now…..Bye

I passed the test today with a little over 900 points. The labs are the same as the ones presented here, just the IP addresses might differ and the ospf process and areas. The only thing you have to add to the configurations shown on this website is the distance eigrp 90 105 for the redistribution sim.

The questions are from whatever dumps you decide to follow. I also had 3 D&D but nothing crazy. Before going through the questions I read the Official certification guide by Odom and went through the videos from cbt nuggets.

Good luck everyone! Now switching to switching

@Ambro2000
congrates and my exam is today after 4 Hrs .

@xpman,

wow, claim it that you will pass :-), give us an update ok :-) ? and give us tips about the exam :-) hehehe thank you :-)

Richel is this free? can i borrow your account?

Passed today. Thanks to a lot of websites including this. Three labs (would you believe it…very similar what you see in this website) Read LSA types, BGP attributes, LSA types. Write your own notes for each topic. I found it very useful to understand detail information. Do the Labs in GNS couple of times to inderstand. Goodluck.

in only 1:15 min i changed from xpman to ccnpman :
clear the exam today with 965
total 50 Qs passing score 790
LABs :1- OSPF-EIGRP (IPs diff and the figure of toplogy also changed but same concept,dnt forget #distance eigrp 100 90 105 at R2.
2- OSPF IPV6 virtual the same.
3- PBR same with diff IPs
4-ospf stub router with diff names and IPs .
only copy run start work in ospf stub only
2 DND same as in nonentity dump
3 new Qs from Actual test6.2 322
my sources of study are
-Authorized self study guide 642-901 3rd addition
-ccnp v6 academic course
-CTB Nuggets video
-and finally the powerful great site digitaltut

@xpman Congrats

In exam how many question are from Actualtest 6.2

@Anonymous
about 3 Qs about GRE and ipv6

@xpman Actualtest 6.2 is valid for exam

@Anonymous
yes ACTtest 6.2 is valid + nonentity Rev7 and LAbs as in digitaltut that you will need to pass .

Thanx a lot Xpman

@Xpman
how many drag and drop questions? from where I can download it?

please share the link for ACTtest 6.2 and nonentity Rev7

Please, anybody can share CBT nuggets ROUTE 642-902? all the links are down due to SOPA law, i’m getting tired of this law, all the servers are retiring the contents. thanks!

@boyi10
from http://www.inetstudies.com/
you can free download CBT

@xpman

Congrats……I will also going to give the exam in a few days…

@xpman

Thank you very much! very useful link

Passed today with 988/1000 points.

Labs from here, questions from P4S and ActTest.
Thanks alot guys.

The trick on using this site and the dumps is not memorizing them but rather understand why those answers are the correct ones. Also try and use the knowledge acquired in real life environments because sims and books are one thing, but real life setups are far more complicated and takes alot of brainpower to actually understand whats going on there ^_^

Passed routing today with 988/1000 points.

In my exam 4 labs pbr, redistribution, IPv6 ospf, ospf stub
guys be careful in ospf stub because they change the requirement. so learn the concepts.
and nonenity and actualtest 6.2 is valid.
and other labs are same as digital tut. Thanx a lot for this site and CBT nuggets
this site is great for exam. So guys best of luck.

Now move to switch.

Hi all,

Congratulations who had passed their Route exam. I am preparing for CCNP Route in 15 days. Could you please send the latest dumps to sanprithi@gmail.com. This would be great help.

just wondering …. in real exam,do questions have same choices to choose

just wondering …. in real exam,do questions have same choices to choose as in dumps

yes.. but the orders of the answers are different.. so dont just memorize the answers (b is the answer for example). You need to study the question and answers.

Passed route exam today with 945.except 4 questions all are from dumps

Passed my exam today. Score 860.
Things to note down.
- order of the questions were different
- BGP questions were there alot. So study it thoroughly
-4 Simulations. IP were different.

OSPF Stub
Redistribution Use on R2 # distance eigrp 90 109
IPv6 Virtual link
Policy Based routing

-OSPF Stub simulation were asking different things. Its asking RI Portland S0/0 to Ping to Lynaic loopback interface also.

-Interfaces will be change in real exams. Like instead of Fa0/0 its Fa0/1
-IPv6 questions and GRE tunnel questions were there.
-D&D– The one which include show ip typology.. Show ip neighbours one were there.
Other D&D was Sucessor, Feasible Sucessor..one.
- Time limit was 2 hours.
-I got Java error while doing the lab. So dont panic if you came across one. Just notify this to the centre and they will rectify it for u.
Overall I must say its a tough experience. Again this website is so helpful. For those who area planning to give the exams read
Just go through
1 CBT Nuggest Jeromy
2 Practice labs
3 This website
4 Cisco press book
5. Dumps from noenity

Wish you guys best of Luck. Thanks to this website.

-

Has anyone put together the labs for route in GNS3 format like we have the packet tracer labs for CCNA? or have any other links for good ccnp level labs? I have had a flick through a few pages and did not see a link, then again it’s early so I may have been staring straight at them. Thanks.

Passed my last exam, 910 . made some mistake on Policy Routing. Well, i am finally a CCNP :)

Cleared my exam with 1000/1000
4 sims ( OSPF Virtual link , PBR , OSPF , Redistribution )
a few IPv6 questions
Rev 7 is still valid

THanks to all!!!.. i have some questions, im already ccna , ccda and ccnp now. Would it only require me to take only the ARCH exam for me to get CCDP???? Since it has 2 same exam prerequisite which is Switch and Route. thanks in advance!

hey guys,…….in dump bgp order is wrong
1.weight.
2.local pref
3.as
4.locally origin
but on digitultut.com

locally origin comes before AS.cisco.com has the same….locally origin comes before AS.

can you please tell me what is Rev 7 and how can I download it. I just passed CCNA and preparing for ccnp route. Thanks alot.

aim planning to take bgp+mpls exam.can anyone tell suggested books and websites please.

@Mahmood

It’s noentity dump. Below is the Link

http://www.examcollection.com/cisco/Cisco.Passguide.642-902.v2011-09-03.by.nonentity.338q.vce.file.html

What is the correct configuration to enable router P4 to exchange RIP routing updates with router
P1 but not with router P3?
A. P4(Config)# interface fa0/0
P4(Config-if)# neighbor 192.168.10.3
P4(config-if)# passive-interface fa0/0
B. P4(config)# router rip
P4(config-router)#neighbor 192.168.10.3
P4(Config-router)#passive-interface fa0/0

why B is correct here?if we make f0/0 passive,it will not send updates to both p1 and p3 or
may be….
if we configure p1 as neighbor so it will form neighbor relation to p1 but for p3 it will be passive interface…

am i getting it right
please help me if i am missing something here.thanks

ospf implementation d&d…

Update query boundaries
Summarization boundaries
OSPF Process ID that will be used
OSPF area and associated prefixes

not sure it should include update query boundaries.i think correct is authentication type

q is from pdf dump

@Anonymous:
Question: What is the correct configuration to enable router P4 to exchange RIP routing updates with router P1 but not with router P3?

Response: One can configure “passive-interface” and “neighbor” command in router configuration mode.

for redistribution sim,I am doing as following,but r1 is going through r2 to r4 not r2 to r3 and r4.please help me to see what I am doing wrong?I know for eigrp metric I put 100 for everything ,just following cbt nuggets ..does it matter to right correct bw,delay,load etc.because they all have adjacency with each other.

router eigrp 100
redistribute ospf 1 metric 100 100 100 100 100
network 192.168.1.0
network 192.168.2.0
distance eigrp 90 105
auto-summary
!
router ospf 1
log-adjacency-changes
redistribute eigrp 100
redistribute eigrp 1 metric-type 1 subnets
network 192.168.3.0 0.0.0.255 area 24
!

Hi Everyone,
First I want to give my thanks to digitaltut & all the helping hands here.
Today I have passed with 895 and the time I took for exam was 57 minutes.

Any way, I have got 3 Lab (IPv6, OSPF & PBR) with ip address changed.
3 D&D, no simlet.
Some totally new questions I have got there.
But pass guide is still can give yo pass mark.

http://www.4shared.com/file/KO7HhUAu/PassGuide_P4S__CCNP642-902_v28.html

!!! Congrats !!!!