Home > Share your ROUTE v2.0 Experience

Share your ROUTE v2.0 Experience

January 22nd, 2015 in ROUTE 300-101 Go to comments
Note: The last day to take this ROUTE 300-101 exam is February 23, 2020. After this day you have to take new Enterprise exams to get new CCNP Enterprise certification. If you want to find out more about the new exams please visit here.

The ROUTE 300-101 (ROUTE v2.0) exam has been used to replace the old ROUTE 642-902 exam so this article is devoted for candidates who took this exam sharing their experience.

Please tell with us what are your materials, the way you learned, your feeling and experience after taking the ROUTE v2.0 exam… But please DO NOT share any information about the detail of the exam or your personal information, your score, exam date and location, your email…

Note: Posting email is not allowed in the comment section.

Your posts are warmly welcome!

Comments
Comment pages
1 114 115 116 117 118 391 1008
  1. Almost there..
    April 26th, 2018

    @Venice

    Most of the questions are similar in Dexter with 477, I have read both and i have test on Friday.
    Good luck everyone

  2. Almost there..
    April 26th, 2018

    @TheSilentLamb

    The answer is A according 477 latest version

  3. ccnp route
    April 26th, 2018

    Pass exam Monday 91x point ,Lab Eigrp stub , Eigrp and Ospf evaluation.
    D&D FrameRelay,AAA,GRE and ACL .About 8 new question IPSLA , FrameRelay and DHCP , Most of question are from Prince91 .

  4. rrr
    April 26th, 2018

    hello

    can someone convert this into a vce and send ot to ccnp7410 gmail com?

    Thanks;)

    h t t ps : / / w w w . d ropbox.com/s/0wkpzo4iap7dsth/300-101%20-%20477q%20-%20correctedv31.pdf?dl=0

  5. khaled
    April 26th, 2018

    Two scenarios for preventing fragmentation on GRE tunnel? (Choose two)
    A. TCP MSS
    B. DF Bit clear
    C. IP MTU
    D. PMTUD

    some says AD and some says AB.

    please tell me what is the correct answer with explainations :)

  6. TheSilentLamb
    April 26th, 2018

    @khaled
    according to cisco is D

    Two scenarios for preventing fragmentation on GRE tunnel? (Choose two)
    A. TCP MSS
    B. DF Bit clear
    C. IP MTU
    D. PMTUD

    What Is PMTUD?
    TCP MSS as described earlier takes care of fragmentation at the two endpoints of a TCP connection, but it does not handle the case where there is a smaller MTU link in the middle between these two endpoints. PMTUD was developed in order to avoid fragmentation in the path between the endpoints. It is used to dynamically determine the lowest MTU along the path from a packet’s source to its destination.

  7. TheSilentLamb
    April 26th, 2018

    @khaled , also A.

  8. Dan_2_One
    April 26th, 2018

    @Almost there..

    good luck to you. and keep us updated after your test

  9. Anonymous
    April 26th, 2018

    Hi,

    What is last dump 300-101, question number?

  10. Ghauri
    April 26th, 2018

    @ccnp route
    will you share those new 8 questions if you remember. which dumps did you study?

  11. EagleCrow
    April 26th, 2018

    So are the questions from the 477 exact as to the exam?

  12. TheSilentLamb
    April 26th, 2018

    Ive got some corrections for the Prince91q , I thinks these are correct but if Im wrong please do tell me so

    Prince 91Q corrections:
    * QUESTION 1 and Question 91 are the same

    QUESTION 23
    Which command do you enter to filter only routing updates that are sent through interface
    GigabitEthernet0/0?
    A. R1(config-if)#passive-interface GigabitEthernet0/0.
    B. R1(config-router)#no passive-interface GigabitEthernet0/0
    C. R1(config-router)#passive-interface GigabitEthernet0/0
    D. R1(config-router)passive-interface default
    E. R1(config-if)#passive-interface default
    F. R1(config-router)#distribute-list 1 GigabitEthernet0/0 out
    Correct Answer: C (Dump say its F)

    QUESTION 31
    Which feature can mitigate fragmentation issues within network segments that are between GRE
    endpoints?
    A. PMTUD
    B. ICMP DF bit
    C. TCP Flow Control
    D. TCP MSS
    Correct Answer: A (Dump say its D)

  13. Almost there..
    April 26th, 2018

    @TheSilentLamb

    I agree with you on those answers

  14. King
    April 27th, 2018

    My Comment what happen if my CCNA Expires couldn’t take ccnp?

  15. Dan_2_One
    April 27th, 2018

    @TheSilentLamb

    I also Agree, your answers are correct

  16. John
    April 27th, 2018

    Hi,

    I am planning to do the exam on next week Please any one share the dump i don’t have time limit to study need to complete on next month please any one help me to share the dump!!!

  17. Almost there..
    April 27th, 2018

    @John

    forum page 100 -> other materials -> at dropbox link
    forum page 108 -> corrected by Prince 477q (v31) -> at dropbox link
    forum page 111 -> 91q the most valid :-) made from 477q by Prince ->-> at dropbox link
    Forum page 115 DND (from Jazzy – link there)

    These are the latest and most up to date material Good luck

  18. GO
    April 27th, 2018

    Please share the VCE player 1.1.7 with crack download link

    Can any one share the download link of VCE Player 1.1.7 with crack. I have 1.1.7 cracked version but presently not working properly. please give me setup asap then i will be able to take exam in first week of May. I am waiting from all of u

  19. cisconinja
    April 27th, 2018

    @TheSilentLamb & @Almost there

    Question 23 is correct – passive interface won’t filter. it will stop all the route updates/hello messages.

    I agree with you on question 31 – PMTUD (path mtu discovery)

  20. newbie
    April 27th, 2018

    Passed today. 8xx
    477 is valid. Just read and find correct answer.

  21. Almost there..
    April 27th, 2018

    @newbie

    Which labs you had and DND please share some info.

  22. Raven
    April 27th, 2018

    just passed the exam today, study the 477q dumps, the DND and lab on this site and you’ll surely pass. Goodluck!

  23. TheSilentLamb
    April 27th, 2018

    @cisconinja

    I made some research and you are right about Q23 (F right answer)
    QUESTION 23
    Which command do you enter to filter only routing updates that are sent through interface
    GigabitEthernet0/0?
    A. R1(config-if)#passive-interface GigabitEthernet0/0.
    B. R1(config-router)#no passive-interface GigabitEthernet0/0
    C. R1(config-router)#passive-interface GigabitEthernet0/0
    D. R1(config-router)passive-interface default
    E. R1(config-if)#passive-interface default
    F. R1(config-router)#distribute-list 1 GigabitEthernet0/0 out

    The cisco official documentation says that route filtering is with distribution lists

    the passive-interface command restricts outgoing advertisements only. But, when used with Enhanced Interior Gateway Routing Protocol (EIGRP), the effect is slightly different. This document demonstrates that use of the passive-interface command in EIGRP suppresses the exchange of hello packets between two routers, which results in the loss of their neighbor relationship. This stops not only routing updates from being advertised, but it also suppresses incoming routing updates.

    Router#show ip protocols

    Displays the parameters and current state of active routing protocols

    Routing Protocol is “eigrp 10”
    Outgoing update filter list for all interfaces is 2
    Redistributed ospf 1 filtered by 5
    Serial 0/0/0 filtered by 4
    Incoming update filter list for all interfaces is 1
    FastEthernet0/0 filtered by 3

  24. TheSilentLamb
    April 27th, 2018

    UPDATE on Prince 91q
    QUESTION 40
    Logging Console7
    Which option is one of the effects entering this command on a Cisco IOS router, with no additional
    logging configuration?
    A. Debug messages can be seen on the console by enabling “terminal monitor.
    B. Debug messages are logged only on active console connections.
    C. A user that is connected via SSH sees level 7 messages
    D. The router can experience high CPU utilization

    Correct answer is D (Dump says is B)

    Console logging:

    The router does not check if a user is logged into the console port or a device is attached to it; if console logging is enabled, messages are always sent to the console port that can cause CPU load.

    source:
    supportforums cisco com/t5/network-infrastructure-documents/how-to-configure-logging-in-cisco-ios/ta-p/3132434

  25. Ghauri
    April 27th, 2018

    @Raven
    I see mostly the sims on this website. will you clarify which are the labs available on this websit. thx

  26. airon
    April 27th, 2018

    @TheSilentLamb

    Correct answer is: R1(config-router)#passive-interface GigabitEthernet0/0

    The cisco official documentation says that “route filtering” is with distribution lists but NO routing Updates. If you want to perform filtering of routing updates you use Passive-interface.

    Preventing Routing Updates Through an Interface

    Using the passive interface command can prevent routers from sending routing updates through a router interface.

    Controlling the Processing and Advertising of Routes in Routing Updates

    To control the advertising and processing of routes in routing updates, use the distribute-list command.

    Correct answer is: C. R1(config-router)#passive-interface GigabitEthernet0/0

  27. TheSilentLamb
    April 27th, 2018

    @airnon man, thanks there is another question similar to that one and verifies what you are saying.

    It ask about how to prevent routing updates from being sent to access layer switches.
    and all the answers are passive interface

  28. unstoppable
    April 27th, 2018

    Hi All,

    for Policy Based Routing Sim, why the first line is
    BorderRouter(config)#access-list 101 permit tcp any any eq www

    why permit tcp?
    is that mention in the exam that need to be tcp?

    many people comment:

    need to add this :

    route-map PBR permit 20
    set ip next-hop 10.1.101.2

  29. TheSilentLamb
    April 27th, 2018

    @unstoppable
    Permit TCP

    because http (port 80) is a TCP port, also the permit part is due to match the list (the ACL in this case is not about permiting or deniying, you use permit so the traffic matched by the ACL is used in the routemap)

  30. MOhamed Atef
    April 27th, 2018

    please anyone can send me prince 91Q om my email:
    mohamedatefelgendy at gmail.com

  31. rrr
    April 27th, 2018

    @TheSilentLamb,
    @airon

    is this the correct answer then?

    R1(config-router)#passive-interface GigabitEthernet0/0

  32. Almost there..
    April 27th, 2018

    Hello Guys,

    Just passed with 823, However i didnt configure the stub routing sim the system had some issues.
    EIGRP EVA
    OSPF EVA
    GRE DND
    ACL DND
    FRAME RELAY DND WITH A TOPOLOGY OF 3 ROUTERS

    However 477 is still valid with 91.
    I would like to thank this forum and all the amazing people putting effort to make thinks possible.
    Good luck see you guys in T-Shoot

  33. CCNP 10
    April 28th, 2018

    hello Guys

    which is the best answer for this Q

    9TUT :

    The enterprise network WAN link has been receiving several denial of service attacks from both IPv4 and IPv6 sources. Which three elements can you use to identify an IPv6 packet via its header, in order to filter future attacks? (Choose three)
    A. Traffic Class
    B. Source address
    C. Flow Label
    D. Hop Limit
    E. Destination Address
    F. Fragment Offset

    Answer: A C D

    The components of IPv6 header is shown below:

    The Traffic Class field (8 bits) is where quality of service (QoS) marking for Layer 3 can be identified. In a nutshell, the higher the value of this field, the more important the packet. Your Cisco routers (and some switches) can be configured to read this value and send a high-priority packet sooner than other lower ones during times of congestion. This is very important for some applications, especially VoIP.
    The Flow Label field (20 bits) is originally created for giving real-time applications special service. The flow label when set to a non-zero value now serves as a hint to routers and switches with multiple outbound paths that these packets should stay on the same path so that they will not be reordered. It has further been suggested that the flow label be used to help detect spoofed packets.
    The Hop Limit field (8 bits) is similar to the Time to Live field in the IPv4 packet header. The value of the Hop Limit field specifies the maximum number of routers that an IPv6 packet can pass through before the packet is considered invalid. Each router decrements the value by one. Because no checksum is in the IPv6 header, the router can decrease the value without needing to recalculate the checksum, which saves processing resources.

    =========================

    Prince 477 : Q84

    A. Traffic Class
    B. Source address
    C. Flow Label
    D. Hop Limit
    E. Destination Address
    F. Fragment Offset

    Answer: B C E

    Thanks

  34. Ghauri
    April 28th, 2018

    @CCNP-Route
    why are you putting switch stuff to route web page. Just go to switch web page.

  35. Eng.
    April 28th, 2018

    Vince.Would u kindly share the 477 & Dexter dumps please

  36. C1sc0g33k
    April 28th, 2018

    Just passed today with 9XX/1000

    Dumps are valid. The DND too.
    Labs: OSPF eval, EIGRP eval, EIGRP Stub sim

    Thank you all for tour contributions.

  37. Quest
    April 28th, 2018

    Hi everyone

    Yesterday i pass the exam with 867/xxx.
    477 q with corrections is stilll valid.
    I have eigrp evaluation, pbr lab, eigrp stub.
    A lot of questions about ip sla and ipv6.

    dnd

    ipv6 dhcp
    AAA
    address registration / global address ecc
    gre feature
    frame relay component
    adverse network condition (that one with excessive unicast fluding, asymmetric routing ecc)

    There are two new questions in my exam. One about bgp (i see that question in this forum and i choose the anwer with update source), and one about what you see with show ip eigrp vrf xxx topology.

    I don’t remember all the answer.
    I chose the one that say that you can see the successor of a specific routing table.

    Good luck and thanks to all.

  38. TCP-Connect
    April 28th, 2018

    Question 177
    A netwirk eogineer wants ti ensure an optmal end-to-end delay bandwidth product. The delay is
    less than 64 KB. Which TCP feature ensures steady state throughput?
    A. Window scaling
    B. Network bufers
    C. Round-trip tmers
    D. TCP ackoiwledgmeots
    Answer: A

    why NOT option C ?

    Throughput and Delay affect on BDP, not Window Scaling.

  39. TCP-Connect
    April 28th, 2018

    Question 180
    A network admin creates a statc route that points directly to a multaccess interface, instead
    of the next-hop IP address. The admin notices that Cisco Express Forwarding ARP requests are
    being sent to all destinations. Which issue might this configuration create?
    A. Low bandwidth usage
    B. High memory usage
    C. Cisco Express Forwarding routing loop
    D. High bandwdith usage
    E. IP route interference
    Answer: C

    I think the correct answer is B, not C.

  40. khaled
    April 28th, 2018

    @TheSilentLamb

    thanks man for answering my question, and for being active in this fourm.

    wish u, me and all the members here to pass the ccnp route ..

  41. TCP-Connect
    April 28th, 2018

    Question 216
    Which two GRE features can you configure to prevent fragmeotatin? (Chiise Two)

    A. IP MTU
    B. MTU ignore
    C. TCP MSS
    D. UDP windows sizes
    E. MTUD
    F. DF bit clear

    Answer: CF is NOT correct.
    I think that options A and C are correct.

    For example,
    Router(config)# interface tunnel 6
    Router(config-if)# ipv6 tcp adjust-mss 1340
    Router(config-if)# ipv6 mtu 1400

  42. TCP-Connect
    April 28th, 2018

    Question 224
    Using new backup router in spite of faulty one in ospf domain but relationship with neighbor in one interface only not working , what is the reason of this problem? (Choose 2)
    A. area Id mismatch
    B. authentication mismatch
    C. process id of ospf not match
    D. OSPF timers not match
    Aoswern AD

    Option B migh also be correct, because authentication may be configured on an interface basis as well.

  43. Anonymous
    April 28th, 2018
  44. TCP-Connect
    April 28th, 2018

    Which type of information is displayed when a network engineer executes the show track 1 command on the router?
    A. information about tracking list 1.
    B. time to next poll for track object 1.
    C. information about the IP route track table.
    D. tracking information statistics.
    Answer: C

    The option D is correct either.

  45. rrr
    April 28th, 2018

    @Almost there

    congrats! ;)

    can you remember which q-s you got from q91?

    whats next, tshoot?

  46. CCNP 10
    April 28th, 2018

    Hello Guys

    Another Q with different Answers

    Digitaltut :

    Other than a working EIGRP configuration, which option must be the same on all routers for EIGRP authentication key rollover to work correctly?
    A. SMTP
    B. SNMP
    C. Passwords
    D. Time

    Answer: D
    Explanation
    Requirements
    + The time must be properly configured on all routers.
    + A working EIGRP configuration is recommended.
    Reference: https://www.cisco.com/c/en/us/support/docs/ip/enhanced-interior-gateway-routing-protocol-eigrp/82110-eigrp-authentication.html

    =============================

    477 Dump Prince

    Q154

    A. SMTP
    B. SNMP
    C. Passwords
    D. Time

    Answer: DA. SMTP
    B. SNMP
    C. Passwords
    D. Time

    Answer: C

    which is the best answer ?

    Thanks

  47. 1000
    April 28th, 2018

    please is 477 with correct from prince and digital tut enough to pass

  48. Sensitive
    April 28th, 2018

    @ tcp-connect

    For this question , I say answer is A but dumps I have is saying its D. So whats the right and can you explain

    Which type of information is displayed when a network engineer executes the show track 1 command on the router?
    A. information about tracking list 1.
    B. time to next poll for track object 1.
    C. information about the IP route track table.
    D. tracking information statistics.
    Answer: C

    The option D is correct either.

  49. Sensitive
    April 28th, 2018

    All,

    I attempted last week route exam but not able to pass though got 768

    I can suggest

    doing 7 labs of ccnp route in digitaltut, Refer to exhibit questions and drag and drop is definitely covers 60 percent exam..

  50. Sensitive
    April 28th, 2018

    All,

    I need help in confirmation of following questions

    Which two options are limitations of Stateful NAT64? (Choose two)
    A.
    it is unable to route VRF traffic
    B.
    it is unable to route multicast traffic
    C.
    it supports FTP traffic only with an ALG
    D.
    it supports DNS64 only
    E.
    layer 4 supports TCP only

    Refer to exhibit. A user calls from another branch office with a request to establish a simple VPN
    tunel to test a new router’s tunneling capability.
    Based on the configuration in the exhibit, which type of tunnel was configured?
    A. PPTP
    B. IPsec site-to-site
    C. 6to4


  51. Note: Please do not open any suspicious links (especially short links and links that need to remove some words to open) in the comment section above as they are usually spams and may harm your computer.
Comment pages
1 114 115 116 117 118 391 1008
  1. No trackbacks yet.