Share your ROUTE v2.0 Experience

Ok anyone know the answer to question 1 above?

4.What is the default authentication in RIPv2 when authentication is enabled
a. SHA1 authentication
b. Enable password authentication
c. Plaintext authentication
d. MD5 authentication
Answer C
Reference https://www.cisco.com/c/en/us/support/docs/ip/routing-information-protocol-rip/13719-50.html
First: key-string 234 <– Plain text

!— The actual password or key-string. !— It needs to be identical to the key-string on the remote router.

THEN
Second: ip rip authentication key-chain kal

!— Enables authentication on the interface and configures !— the key chain that will be used.

Q3 is from Prince 91. Answer A

5.Which command sequence can you enter on a router to configure Unicast Reverse Path Forwarding in loose mode
a. Interface GigabitEthernet0/0
Ip verify unicast source reachable-via any
b. Interface GigabitEthernet0/0
Ip verify unicast source reachable-via loose
c. Interface GigabitEthernet0/0
Ip verify unicast source reachable-via all
d. Interface GigabitEthernet0/0
Ip verify unicast source reachable-via rx
Answer A
Reference:https://www.cisco.com/c/m/en_us/techdoc/dc/reference/cli/nxos/commands/fibrib/ip-verify-unicast-source-reachable-via.html

Does anyone know the question to 1 above!!!? I have a test in an 1hr

I believe it is b,c,e- can someone confirm?

@Hello
IMHO A,B,C (RIPv2 Protocol)
http://www.ciscopress.com/articles/article.asp?p=1613547&seqNum=2
https://www.cisco.com/c/en/us/td/docs/ios/12_2/iproute/command/reference/fiprrp_r/1rfrip.html

Bad news.

I just took my exam. Question has changed!!

704/1000!

Sims are same. But around 30 new questions i’ve never seen!

Hi Ab, what sim did you find?

Am preparing for the same too

@ja

Hi, i had redistribution, stub, ospf.

Some new d&d +
Acl d&d
Dmvpn d&d

I will retake my exam next few weeks.

Please if anyone has new materials.. Provide me it!

@Abdul what was the new DnD about?

@Abdul are the new questions you mentioned the same as what was listed by doka1 on the previous page? and the newer queestions added by june14? also, which sims and new d&d did you get? how many d&d in all did you get on the test?

In EIGRP Evaluation Sim Question 1:
Traffic from R1 to R6′ s Loopback address is load shared between R1-R2-R4-R6 and R1-R3-R5-R6 paths. What is the ratio of traffic over each path?
A. 1:1
B. 1:5
C. 6:8
D. 19:80 <—— Correct answer according to digitaltut.

But when I type in R1#show ip route 150.1.6.6
This is what I get:
Routing entry for 150.1.6.6/32
Known via "eigrp 1", distance 90, metric 161280, type internal
Redistributing via eigrp 1
Last update from 192.168.13.3 on FastEthernet1/0, 00:05:30 ago
Routing Descriptor Blocks:
192.168.13.3, from 192.168.13.3, 00:05:30 ago, via FastEthernet1/0
Route metric is 1636608, traffic share count is 1
Total delay is 62930 microseconds, minimum bandwidth is 100000 Kbit
Reliability 255/255, minimum MTU 1500 bytes
Loading 1/255, Hops 3
* 192.168.12.2, from 192.168.12.2, 00:05:30 ago, via FastEthernet0/0
Route metric is 161280, traffic share count is 10
Total delay is 5300 microseconds, minimum bandwidth is 100000 Kbit
Reliability 255/255, minimum MTU 1500 bytes
Loading 1/255, Hops 3

Can someone explain why I get 1:10 ratio instead of 19:80?

1.Which three methods can a network engineer use to fix a metric based routing loop in the network.
a. Implement offset lists at network boundaries
b. Filter routes manually using distribute lists
c. Filter routes manually using prefix lists
d. Implement proper network summarisation on key routing points
e. Filter routes based on tags
f. Utilise root database filters

answers are a, b and e…. prefix lists can not be used to filter rotes by itself, they can be used inside of distribution lists… were the link to how to use tagging method: https://itpro.tv/course-library/ccnp-routing-switching/loop-prevention/

@and
OK, i aggre with you :)

@doca
when are you going to pass?

Either next week or in July

Can someone help me with my question?
Maybe there is something wrong with the lab. Because at Question 4 I get another answer aswell

@Alright
If you configured it on gas3 you should verify all the interface parameters to be the same like in the lab. the ratio calculation is based on metric. you have 1636608 versus 161280 that is approximately 1/10. you can play with metric in order to manipulate path selection…….
the lab is only to understand how to find your answer…

@and
Thank you for your response, I’ll configure to the correct ratio to be the same as on the labs.

is there any one els who have taken an exam today or a few days before? any new questions…?

I took my exam today and passed 8xx. The dumps are valid for the most part, I encountered about 15-20 new questions. I got the redistribution sim, ospf sim, and eigrp stub sim. DnD’s from the dumps, old. I feel its definitely hard to pass using only dumps, but its possible, just dont expect a high score. If you have a good foundation about CCNA, CCNP Route, you should be able to pass even with the new questions, they weren’t totally confusing questions.

Vimal

@vimal first of all Congrats!! from the 15-20 questions you encountered, the questions that have been posted in the forum cover them? or do you happen to remember other new ones that were not posted? thx

@ all which OSPF sim are you guys getting? is is the virtual link? ospf eval? or standard ospf sim?

@Mario, only 2 question the one about chapv2 new features and the one where the answer was something about firewall udp 520.
Im sorry it was so stressful while taking the exam i dont remember them. There was a question about Hub/Spoke and Nat config, Exhibit with Vnet trunk, SNMP traps and informs. Sry I cant remember anything else.
Also I encountered the standard ospf sim
Good Luck to Everyone else, I am going the switching site now to prepare for my next exam, thanks for all the help and i hope to see you all there.

Vimal

guys please need your help

which dumps valid my Exam next week
plz help me
@Vimal

@Vimal thanks for the info. what was the total D & D you get on the test?

@vimal is the NAT question that you saw the following?

which statement describes what this command accomplishes when inside and outside interfaces are correctly identified for NAT?

ip nat inside source static tcp 192.168.1.50 80 209.165.201.1 8080 extendable

answer: it allows external clients to connect to a web server hosted on 192.168.1.50

Hi guys, I am gonna take the exam on monday 477Q and 91Q is valid ? anyone can help me?

Ok, I failed today, however I did improve since last time. But this is what I was able to pull away.
Sims were similar. Dnds were expected. MCQ are definitely different. I cannot remember exact questions but only topics that might need more investigation. See below

-Benefits of evn
-Logging trap #?
-Statefull nat64
-Something about using ipv6 and ipv4 support for vrf from service provider
-Something about bgp neighbors and how they update
-Evn trunks implementation
-Ntp authentication
-Aaa local authentication
-Nat over dmvpn

Hope this helps

What is the new DnD regarding Frame-Relay?

Can someone please help posting what labs come, and show commands ones ??

Madmartigan

Did you use any dumps, and if so did you recognize any questions from the dumps?

@hello99

Yes, if you go back a couple of days in this thread there were several that look familiar on the test, so it was helpful

@Madmartigan

Thank you, I will make sure to give them a look. I’m taking it tomorrow. Did you use anything like the Jazzy 477, Prince 91 Q or Kikavich?

Any recommendation for a valid vce dump please ? ,, will take my exam next week ;..

@Madmartigan did you recognize any of the questions as old or are they completely new?
About log trap#, was the question about logging information at a certain level?

Hi anyone , can u share any update questions in your exam as u remembered that !

Please

Refer to the exhibit. A network engineer executes the show ipv6 ospf database command and is presented with the output that is shown. Which flooding scope is referenced in the link-state type?
(Exhibit missing)

A. link-local
B. area
C. AS (OSPF domain)
D. reserved

Whats the correct answ

@ Hello99

Yes, those were all helpful, yet try to understand why they got those answers. Explanations are key in that they will define the subject matter which will let answer you answer new questions that cisco might throw at you.

@ Alright

I have this sneaky suspicion that cisco is pulling these “new” questions from past exam versions. And yes, u are correct about the trap question

@Mario i got like 3 dNds, the one about ACL types and frame relay lmi extensions and CEF adjacency types

No the NAT question had to do with static NAT / PAT on spoke/hubs…it was very confusing question i most likely got it wrong.

Vimal

Hi guys
Dontou think Jazz 477q and P 91Q still valid? Because the topics that @Madmartigan mentioned seems to familiar to me…

@Vimal
is this it?
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/sec_conn_dmvpn/configuration/xe-3s/sec-conn-dmvpn-xe-3s-book/sec-conn-dmvpn-dt-spokes-b-nat.html

passed with a good score.
same drag drop and same labs with few new questions. thanks all for your grate help to this forum.. trying to remember 4 new questions.

1. Where must a network engineer configure the ip helper-address command on a router
a. On the interface that will receive the broadcasts
b. On the DHCP configuration
c. the interface that is closed to the destination DHCP server
d. on the global configuration mode

2. Which feature can be used to reduce the number of ICMP unreachable message egressing a router
a. uRPF
b. ICMP rate-limiting(upendra)
c. ip unreachables command
d. Asymmetric routing

3.What happens when a router receives a route with an administrative distance of 255
a. The router installs the route as the most preferred path in the routing table.
b. The router installs the route as the least preferred path in the routing table
c. The router becomes the feasible successor for the route
d. The router is unable to install the route into the routing table

4. A network access serve using TACACAS+ for AAA operations receives an error message from the TACACS+ server. which action does the network access server take next ?
a. It attempts to authenticate the user against RADIUS
b. It restarts and attempts to reconnect to the TACACS+ server
c. It rejects the user access request the
d. It checks the method list for an additional AAA option

Thanks Vimal. did you see the questions that www just posted?

@www congrats! did you get the list of questions posted in the forum? thx

1. Where must a network engineer configure the ip helper-address command on a router
a. On the interface that will receive the broadcasts
b. On the DHCP configuration
c. the interface that is closed to the destination DHCP server
d. on the global configuration mode

A is correct … CCNA basic :)

3.What happens when a router receives a route with an administrative distance of 255
a. The router installs the route as the most preferred path in the routing table.
b. The router installs the route as the least preferred path in the routing table
c. The router becomes the feasible successor for the route
d. The router is unable to install the route into the routing table

If the administrative distance is 255, the router does not believe the source of that route and does not install the route in the routing table –> Answer D

1.A
2.B
3.D
4.C

@www what do you think about my answers?

1. Where must a network engineer configure the ip helper-address command on a router
a. On the interface that will receive the broadcasts < correct answer
b. On the DHCP configuration
c. the interface that is closed to the destination DHCP server
d. on the global configuration mode
2. Which feature can be used to reduce the number of ICMP unreachable message egressing a router
a. uRPF
b. ICMP rate-limiting(upendra) < correct answer
c. ip unreachables command
d. Asymmetric routing
3.What happens when a router receives a route with an administrative distance of 255
a. The router installs the route as the most preferred path in the routing table.
b. The router installs the route as the least preferred path in the routing table
c. The router becomes the feasible successor for the route
d. The router is unable to install the route into the routing table < correct answer
4. A network access serve using TACACAS+ for AAA operations receives an error message from the TACACS+ server. which action does the network access server take next ?
a. It attempts to authenticate the user against RADIUS
b. It restarts and attempts to reconnect to the TACACS+ server
c. It rejects the user access request the
d. It checks the method list for an additional AAA option < correct answer