Share your ROUTE v2.0 Experience

Passed today with 9xx/1000.

3 Labs: EIGRP stub, PBR, EIGRP eval

6 DNDs: DHCP, adverse network conditions, AAA, Frame-relay component and LMO, TACACS+ACL

https://drive.google.com/open?id=1bCvqmgh1iMV4gF1KTEOEAKxGnB5yqY3I

passed the exam today!!! here is the legit dumps. shout out to networkinggggg! thank you very much!!
https://drive.google.com/drive/folders/1Cf4MHTm8Qt5-_jYzJt6PXNy6b6YOBEx1

https ://drive.google.com/drive/folders/1Cf4MHTm8Qt5-_jYzJt6PXNy6b6YOBEx1

Remove space: this is from nneettwwoorrkkiinngg !!!

Thanks

hi all in this question
I found different answers what are the right answer ?
please help me i take my exam tomorrow:

Which adverse circumstance can the TTL feature prevent?

A. routing loops
B. DoS attacks
C. link saturation
D. CAM table overload

a or b
Which value determines the amount of traffic that a network path can hold in transit?

A. route cache setting
B. maximum window size
C. bandwidth delay product
D. MSS

c or d

Which two statements about ICMP unreachable messages are true? (Choose two)

A. They are sent when a route to the destination is missing from the routing table
B. They can be enabled and disabled on a device only on a global level
C. They are sent when a destination address responds to an ARP request
D. They include the entire packet so that the source can identify the process that generated the message
E. They include a portion of the original data so that the source can identify the process that generated the message

??

Refer to the exhibit.

interface gigabitethernet 2/0/0
vnet trunk
ip address 192.168.1.1 255.255.255.0
vnet name cisco
Which effect of this configuration is true?

A. It designates the interface as a GRE tunnel endpoint
B. It configures 802.1q trunking on the interface
C. It designates the interfaces as an EVN trunk
D. It removes VTP from the interface

b or c

Company is deploying a multicast application that must be accessible between sites, but must not be accessible outside of the organization. Based on the scoping requirements, the multicast group address for the application will be allocated out of which range?

A. FF00:/16
B. FF0E:/16
C. FF02:/16
D. FF08:/16

c or d

Which two causes of latency are true? (Choose two)

A. High bandwidth on a link
B. Split horizon
C. Propagation delay
D. Serialization delay
E. Under-utilization of a link

c e or c d

When OSPF is forming an adjacency, in which state does the actual exchange of the information in the link-state database occur?

A. INIT
B. loading
C. exstart
D. exchange
b or c

thk so much

Who passed the exam, What about the IP addresses in the Labs, They was same as here ?
Like, OSPF Sim (Portland, Amani, Lynaic)

W w w.cciedumps.xyz/ccna_rs.php?utm_source=bbs&utm_medium=bbs

The inside of this turn is real and effective, if you need it, you can go and see.

https ://drive.google.com/drive/folders/1Cf4MHTm8Qt5-_jYzJt6PXNy6b6YOBEx1

Remove space: this is from nneettwwoorrkkiinngg !!!

Thanks

Hi,

Any one have 195Q dump

Thank

@Rene Sege

Thanks for sharing!!!

Would you like to upload the newest version of Pass Leader 300-101 dumps with VCE or PDF files???

Thanks

in

advance!!!

passed the exam 99x/1000

195q dumps from nneettwwoorrkkiinngg still valid.
Thank youuuu digitaltut and nneettwwoorrkkiinngg urdabest! :)

@urdabest
which lab d&d and sim have you in your exam?

@urdabest could you please send me the 195q dumps if you have..
R I f a d h 112 @ gmail.com

Does anyone have Packet Tracer versions of the Route Labs?

Hey people does anyone here have valid switch exams dumps coz that forum isn’t helpful at all. its full of spammers & no one answers. Networking your route dumps were super valid so if you have other, pls share, it would be much appreciated. Cheers

Taking my exam this november.. Hope 195q is still valid by then

in few moment i take my exam
i will update you asap

Hello Mozz,

Can I pls ask how i can get the 195 questions? I have checked the latest pdf networkkkkkking and also teh VCE but its not clear.

Just passed 9xx
Neetworking is still valido
Thk so much to all

@lele just the 195q?

yes all question from 195
lab eigrp ospf and redistribution
D&D acl strict mode lose mode and lmi-frame relay
i had big problem with question mark (?) i don’t found on keyboard no way

Today im pass my CCNP route 300-101

lab eigrp stub, ospfv3 redistribution only

OSPF is configured on routers Amani and Lynaic.
IPv6 OSPF Virtual Link Sim
+ EIGRP OSPF Redistribution Sim:

Can someone please tell me where I can fin the questions.

@BGMN What was the new OSPF Lab that was not in digitaltut? Does anyone know this lab?
I have seen more recent comments about this lab but no one posts anything else about it :|

Does anyone took the exam recently?

Please share your inputs please

@Rene Sege

Thanks for sharing!!!

Would you like to upload the newest version of Pass Leader 300-101 dumps (739q) with VCE or PDF files???

Thanks

in

advance!!!

Hey, can someone advise about the CCNP Route exam, I am preparing for it but I don’t have dumps, also couldn’t find videos covering NAT 64, NPT
also I need a valid dump plzzz
my emailll :
engfaramawy at Hotmail dot com

any help plz

Can anyone tell me how I can get the latest dump? I’m trying to write the exam next week. Plz let me which dump is valid and how to get it?..Thanks

@fewe
Q 1
Answer: C
https ://www.cisco.com/c/en/us/td/docs/ios-xml/ios/snmp/configuration/xe-16/snmp-xe-16-book/nm-snmp-encrypt-snmp-support. html

Q 2
Answer: D
https: //www.reddit.com/r/ccna/comments/7mucrf/how_is_ff0816_different_from_ff0216/

Q 3
Answer : C
https ://www.cisco.com/c/en/us/td/docs/switches/metro/me3600x_3800x/software/release/15-4_3_S/configuration/guide/3800x3600xscg/ RIPng_IPv6.pdf (page 45-4)

Q 4
Answer : B
https: //www.cisco.com/c/en/us/about/security-center/ protecting-border-gateway-protocol.html (BGP Time To Live Security Check)

Q 5
Answer: CE
https ://www.cisco.com/c/en/us/products/collateral/ios-nx-os-software/ios-netflow/ prod_white_paper0900aecd80406232.html (search for command and find the answer in the line above the command)

Q 6
Answer : DE
http ://www.ciscopress.com/articles/ article.asp?p=2294214&seqNum=3
Totally stubby area: This Cisco proprietary area type does not accept external autonomous system routes or summary routes from other areas internal to the autonomous system

Q 7
Answer: B (this is personal conclusion)

Q 8
Answer: A
https ://www.cisco.com/c/en/us/td/docs/ios/12_2/wan/configuration/guide/fwan_c/ wcffrely.html (Enabling Frame Relay Encapsulation on an Interface)

Anyone who took the exam today? is 195q still valid?

@Anonymus
In my opinion there isn’t SNMPV3 authEn, only AuthPriv and this is the correct answer to Q677

@fewe
Q1 A
Q2 D
Q3 C
Q4 A
Q5 CE
Q6 CD
Q7 B
Q8 A

Please can someone tell me what you mean by 195?

I just passed the exam. 9xx

195Q is still 100% valid, and I mean 100%
Sim: EIGRP OSPF Redistribution, OSPF Sim, EIGRP Stub.

Thank you digitut and nneettwwoorrkkiinngg.

Device R1 has 1 Gigabit and 10 Gigabit Ethernet interfaces,Which command do you enter so that takes full advantage of OSPF costs?

A.R1(config router)#auto-cost reference-bandwidth 10000
B.R1(config route-map)#set metric 10000000000
C.R1(config if)#ip ospf cost 10000
D.R1(config router)#auto*cost reference-bandwidth 10000000000
E.R1(config if)# ip ospf cost 100000000
F.R1(config route-map)#set metric 10000

A or C?

@Dorko, Could you pls let me know how can I get this 195 questions
I have check the Networkkkkkking but its all over the palce. How can I exactly get just the 195?

@HM remove spaces

https:// drive.google.com/ drive/folders/ 1Cf4MHTm8Qt5-_jYzJt6PXNy6b6YOBEx1

@Heeyah,

I have got that but my question is: where is the section that shows only the 195?
from PDF, the 195, its allover the placeses.

@all those have took the exam in this day, can you share yoyr experience ?

anyone know if there is a new DnD with frame relay ?

thank you

QUESTION FOR A LAB….

###OSPE EIGRP Redistribution–> can you explain why metrics for OSPF 1 redistribution into eigrp are:

10000 100 255 1 1500

instead of

100000 10 255 1 1500

bandwith is in kbit/s and delay is in ten-of microseconde when specifiying metric values in the redistribute command???

@funghet,
Same question: do you please know if there is a section to find the 195 questions? in PDF, its mixded and the VCE not sure as I dont have the password

Hi All,

Can anyone help me to get the 300-101 dumps? Thanks!

Best Regards

@HM

When you run VCE you will see the checkbox for 195. Its on the picture attached to the link. You will see the arrow

Device R1 has 1 Gigabit and 10 Gigabit Ethernet interfaces,Which command do you enter so that takes full advantage of OSPF costs?

A.R1(config router)#auto-cost reference-bandwidth 10000
B.R1(config route-map)#set metric 10000000000
C.R1(config if)#ip ospf cost 10000
D.R1(config router)#auto*cost reference-bandwidth 10000000000
E.R1(config if)# ip ospf cost 100000000
F.R1(config route-map)#set metric 10000

A or C?

QUESTION FOR A LAB….

###OSPE EIGRP Redistribution–> can you explain why metrics for OSPF 1 redistribution into eigrp are:

10000 100 255 1 1500

instead of

100000 10 255 1 1500

bandwith is in kbit/s and delay is in ten-of microseconde when specifiying metric values in the redistribute command???

27. Which two commands do you need to implement on a router to support pppoe client ?
A. peer default ip address pool
B. mtu
C. bba-group pppoe
D. pppoe enable group
E. pppoe-client dialer-pool-number
Aswers: B and E

28. Which two statements about NHRP in a DMVPN environment are true? (Choose two)
a. It requires each endpoint to have a unique network ID
b. It routes traffic through the tunnel
c. It can identify PIM-SM RPs over a tunnel
d. It can authenticate VPN endpoints
e. It provides address resolution to route traffic

answer: D and E

29. In which scenario can asymmetric routing occur?
a. active/active firewall setup
b. single path in and out of the network
c. active/standby firewall setup
d. redundant routers running VRRP

answer: D ?

30. After reviewing the EVN configuration, a network administrator notices that a predefined EVN, which is known as “vnet global” was configured. What is the purpose of this EVN?
A. It defines the routing scope for each particular caEVN edge interface.
B. It aggregates and carries all dot1q tagged traffic.
C. It refers to the global routing context and corresponds to the default RIB.
D. It safeguards the virtual network that is preconfigured to avoid mismatched routing instances
Answer: C

31. Which CLI command can you enter to permit or deny IPv6 traffic travelling through an interface?
A. access-list
B. access-group
C. ipvsca6 access-class
D. ipv6 traffic-filter
Answer: D

32. A network engineer executes the show ip cache flow command. Which two types of information are displayed in the report that is generated? (Choose 2)
A. top talkers
B. flow export statistics
C. flow sample for specific protocols
D. MLS flow traffic
E. IP packet distribution
Answer: CE

33. A network engineer needs to verify IP SLA operations on an interface that shows on indication of excessive traffic. Whixsch command should the engineer use to complete this action?
a. show frequency
b. show track
c. show reachability
d. show threshold

34. Which option is thasce minimum logging level that displays a log message when an ACL drops an incoming packet?
a. level 3
b. level 6
c. level 7
d. level 5

answer: b

34. Other than a working EIGRP conascfiguration, which option must bes the same on all routers for EIGRP authentication key role over to work correctly?
A. SMTP
B. SNMP
C. Passwords
D. Time
Answer: Cz

27. Which two commands do you need to implement on a router to support pppoe client ?
A. peer default ip address pool
B. mtu
C. bba-group pppoe
D. pppoe enable group
E. pppoe-client dialer-pool-number
Aswers: B and E

28. Which two statements about NHRP in a DMVPN environment are true? (Choose two)
a. It requires each endpoint to have a unique network ID
b. It routes traffic through the tunnel
c. It can identify PIM-SM RPs over a tunnel
d. It can authenticate VPN endpoints
e. It provides address resolution to route traffic

answer: D and E

29. In which scenario can asymmetric routing occur?
a. active/active firewall setup
b. single path in and out of the network
c. active/standby firewall setup
d. redundant routers running VRRP

answer: D ?

30. After reviewing the EVN configuration, a network administrator notices that a predefined EVN, which is known as “vnet global” was configured. What is the purpose of this EVN?
A. It defines the routing scope for each particular caEVN edge interface.
B. It aggregates and carries all dot1q tagged traffic.
C. It refers to the global routing context and corresponds to the default RIB.
D. It safeguards the virtual network that is preconfigured to avoid mismatched routing instances
Answer: C

31. Which CLI command can you enter to permit or deny IPv6 traffic travelling through an interface?
A. access-list
B. access-group
C. ipvsca6 access-class
D. ipv6 traffic-filter
Answer: D

32. A network engineer executes the show ip cache flow command. Which two types of information are displayed in the report that is generated? (Choose 2)
A. top talkers
B. flow export statistics
C. flow sample for specific protocols
D. MLS flow traffic
E. IP packet distribution
Answer: CE

33. A network engineer needs to verify IP SLA operations on an interface that shows on indication of excessive traffic. Whixsch command should the engineer use to complete this action?
a. show frequency
b. show track
c. show reachability
d. show threshold

34. Which option is thasce minimum logging level that displays a log message when an ACL drops an incoming packet?
a. level 3
b. level 6
c. level 7
d. level 5

answer: b

34. Other than a working EIGRP conascfiguration, which option must bes the same on all routers for EIGRP authentication key role over to work correctly?
A. SMTP
B. SNMP
C. Passwords
D. Time
Answer: C

d

@alla

Can you share your esperience about the new drag and drop?

Dorko do all the questions come from Q195?

NEW QUESTION 683
What happens when two EIGRP peers have mismatched K values?

A. The two devices are unable to correctly perform equal-cost routing.
B. The two devices fail to perform EIGRP graceful shutdown when one device goes down.
C. The two devices fail to fryjom an adjacency.
D. The two devices are unable to correctly perform unequal-cast load balancing.

Answer: C

NEW QUESTION 684
Which two features were added in MSCHAP version 2? (Choose two.)

A. Mutual authentication between peers.
B. Using the MD5 hash for stronger security.
C. Using three-way handshakes for authentication.
D. Ability to change an expytired password.
E. Backward-compatibility with MSCHAP version 1.

Answer: AD

NEW QUESTION 685
When an EIGRP router discovers a new neighbor, which packet type does the router send to help the neighbor build its topology table?

A. Replies
B. Requests
C. Updates
D. Queries

Answer: C

NEW QUESTION 686
After configuring RIPng on tytwo routers that are connected via a WAN link, a network engineer notices that two routers cannot exchange routing pdated.What is the reason for this?

A. Either a firewall between the two routers or an ACL on the router is blocking UDP 521.
B. Either a firewall between the two routers or an ACL on the router is blocking TCP 520.
C. Either a firewall between the two routers or an ACL on the router is blocking TCP 521.
D. Either a firewall between the two routers or an ACL on the router is blocking UDP 520.

Answer: A

NEW QUESTION 687
A network engineer is enabling RIPng on a new customer link Under which configuration mode is RIPng enabled?

A. Global
B. Router
C. Interface
D. IPv6

Answer: C

NEW QUESTION 688
Which three algoritzx hms can you configure with the ip cef load-sharing algorithm command? (Choose three.)

A. per-packed
B. Tunnel
C. per-destination
D. Universal
E. Per-source
F. Include-ports

Answer: BDF

NEW QUESTION 689
Which tecnology supports overlapping IP address on a single interace?

A. policy-based routing
B. VRF-Lite
C. On-Demand Routing
D. QoS

Answer: B