Share your ENCOR v1.1 Experience

i know its randomized and the amount of Sims and questions change. i get that, but does anyone have any idea, ballpark what the value of the SIMs are in relation to the entire grade in the exam?

labs are same or similar?

@digitaltut, do we have to practice V1.0 sims as well or just V1.1 is fine?

I’m going to take an exam in December, can I pass the exam if I study v1.1 1-4, Sim, and Part 4-11?

I passed yesterday. 94 questions, including 4 labs:
BGP: Configure 1 router with BGP -> 2 neighbors, 2 loopbacks advertise and BGP router ID.
OSPF: BDR/DR with OSPF priority 0 and. 255
VRF: Identical to the Lab here. Tunnel0 already had the VRF configured, tunnel protection was available in the config and only had to be bound on the Tunnel0-Interface.
Trunk & LACP: Task 1 was to configure the PC access port to “spannig-tree portfast”. Then you should fix a problem on the trunk between SW10 and SW20 so that PC1 can ping PC2. There was no “switchport mode trunk” configured on the trunk and the VLAN100 was blocked on the trunk with “switchport trunk allowed vlan 1,10” – after I allowed also VLAN100, the ping went through. 2nd task was to troubleshoot the LACP port channel between SW20 and SW30 – the 2 ETH ports were not assigned to the port channel. Here, too, it was possible to test with a ping from PC2 to PC3. I only had access to SW10 at the bottom left and 3 PCs for testing. Topology identical to the one here.
Almost all questions were known or similar to the questions here. There were 2 Python drag&drops that were completely new to me.
Otherwise, many, many thanks to the folks at DigitalTut for your excellent work. I prepared with the composite quizzes and the EVE-NG labs for 4 weeks, but this was my 2nd ENCOR certification!

Hi Mosalah, congratulations and thank you for the update.

Passed my exam 28/11

87 questions + 4 labs

My labs were:

Trunk UDLD & LACP Sim
VRF Configuration Sim
OSPF DR BDR Sim 2
eBGP Neighbor Sim

I practiced v1.1 part 1, 2, 3, 4
part 4-11 (old encor)
composite quizzes

Good luck everyone
More practice and everything will be ok

Could anyone please send me the question bank to nunim8045(at)gmail(.)com

I passed this exam last week, I studied
ENCOR v1.1 Questions – Part 1 – 4
ENCOR Questions- Part 4 – 11
ENCOR 350-401 (expired)
Great thanks to Digitaltut guys!
I got just a few questions that are not in the pool, some were re-phrased.
4 labs: eBGP Neighbor Sim, Rapid PVST+ and LACP Sim, OSPF DR BDR Sim 2 and VRF Configuration Sim. This VRF Sim was a challenge to me, something was different. Source, Destination and tunnel IPs were already set, but tunnel0 interface was not in CORP vrf, I had to put it there and once set, all IP info was deleted, had to set source, destination and tunnel IPs again. Then tunnel got up, I could ping remote source from each router. When I followed up with static routes for Vlan 100 and Vlan 101 I could not ping from any router the remote IP:
R10#ping vrf CORP 10.101.2.1 source e0/0.100
R20#ping vrf CORP 10.100.1.1 source e0/0.101
I decided to put both Vlan interfaces into CORP VRF and then I could ping remote sources.

good luck to everyone! study hard and you’ll pass it for sure

Hi,

Passed my exam 01/12.

87 + 4 LABs (OSPF filtering LSA 3 with prefix-list, BGP, TRUNK, LACP, STP, VRF and IPsec)

A lot of questions of products, configuration, SD-ACCESS, Overlay, SD-WAN, DNA, Programability/automation. There are some tricky ones much specific of capturing packet and analyzing everything.

@Vired
Hello, were the questions you had in your exam in digitaltut?

Labs are the same as here ??

for Vrf sim when you configured vlan as a Corp VRF you had to configure also IP for vlan?

@Jimbo
Could you please show the commands for the vlan?

I passed the exam on 01.12.
I got 87 Q + 4 Labs.
Ebgp, vrf, ospf prefix, Lacp.

Ebgp and ospf prefix were the same as digitaltut but different remote-as and ip Adresse.
In the ospf prefix lab, The configuration to permit 0.0.0.0/0 was already configured.

The vrf and Lacp lab tasks were different.
vrf lab : task 1 troubleshooting the tunnel 0 , it was not configured at all.
Task 2, protect the tunnel by ipsec Profil.
It wasn’t any task to configure the ip static route vrf.

Lacp lab: task 1 utilize spanning-tree 32 bit long path cost.
Task2 troubleshooting the trunk. ( check the int configuration, port wasn’t configured?
Task3 troubleshooting the lacp. ( port channel , on interfaces wasn’t configured at all, allow vlan also should be configured)

I studied v1.1 and v old part 4 – 11.
I got about 20 questions that were totally new to me and didn’t see them in digitaltut.
A lot of questions about 40 were in digitaltut but in another form. If you learn logic, you can answer them

@mhd pls could explain what you mean by Lacp lab: task 1 utilize spanning-tree 32 bit long path cost.

@Yes by default the spanning-tree path is short 16 bit, just did “spanning-tree pathcost method long“. This command will change the path cost from 16-bit to a 32-bit value

Verify using sh spanning-tree summary: the pathcost method should be long.

I passed the exam on 01.12

I could say that approximately 5-8 new questions but closely related to those provided from digitaltut.

I had these labs:
VRF configuration – where destination and source, both were missing.
eBGP – with different AS numbers, but same tasks.
OSPF DR BDR – I don’t remember any differences here.
Trunk UDLD & LACP – the topology was like this, I was asked to fix the trunk between SW10 and SW30 (VLAN 100 was missing from PC2) and portchannel between SW10 and SW20, the ports were not configured like part of the channel group.

I hope I’ll help someone with this.

Thak you digitaltut!

@AA CAN YOU REMEMBER SOME OF THE 5-8 questions you encounter in the exams

How many or what percent of questions was from 1-4 quizzes? I wna to know how much to study 4-11?

@Anonymous was there new question in your exams

I passed the exam Today.
I got 87 Q + 4 Labs.
Labs: Ebgp, vrf IPSec, ospf BD/BDR, Trunk UDLD & LACP.

OSPF DR BDR (Sim 2): no difference, except area numbers

eBGP Neighbor: IP subnets and AS numbers have changed

vrf lab : task1 troubleshooting the tunnel 0 , missing tunnel destination config.
Task2: protect the tunnel by ipsec Profile.
Task3: configure the ip static route vrf.

Trunk UDLD & LACP lab: task1 troubleshooting the trunk to have PC2 ping PC1.
sh run int e0/0 missing all trunking confings and allowed vlans
Task2 . config udld aggressive on e0/0
Task3 troubleshooting the lacp. sh etherchannel summ
port channel missing port members, missing channel protocol, interf missing all trunking confings

I had a Cisco bootcamp, but it wasn’t enough. So Digitaltut practice questions helped me a lot.
I studied all V1 and V1-old.
I got approximately 15 questions that were totally new to me and didn’t see them in Digitaltut.
I finished on time
What I can remember:
MC questions: difference between a RIB and a FIB, QoS, LISP proocol, Cisco SD-WAN, Cisco SD-Access,
Wireless, Cisco DNA, NAT, ACLs, VM on linux server, SNR=RSSI+Noise, DHCP option 43, Roaming
EEM syslog patern OSPF interface down, ISE, vlan 222 remote-span, netconf
Configure the logging synchronous command under the vty, AAA, Wireless enable AAA override
Which privilege level is assigned to VTY users?
JSON data syntax
OAuth 2.0 within REST APIs authentication
list = [1, 2]

Drag and drop: Asembly-Puppet, LISP, vNIC-OVA-VMDK-VMX, DHCP (DORA),

One MCQ that I have never seen was NAT config for a web server to allow access from the Internet

I don’t remember seen any Multicast questions.

Were these the 15 questions that where new to you, I mean the ones you mention below

@yakoubou no, those are the one in Digitaltut.
I can remember only the one with the NAT config.

How much studying if any needs to be dnoe for 4-11 if i am comfortable with part 1-4 and all the sim? do you still need to studt the old sections?

I passed the exam 7 dec 2023.
I got 87 Q + 4 Labs.
Labs: Ebgp, vrf IPSec, ospf BD/BDR, Trunk UDLD & LACP.

i got 3 to 5 new questions
one of the questions i could remember is
1. what is the result of this python program (3*5)%
A.7
B.7.5
C.1
D.0
2. type 1 hypervisor runs on
A. runs on bear metal server
b. runs on an os running on running on a physical machine

note* go through digitaltut composite quizzes their are many questions from there

Hi ALL

I passed and a big thank you to Digital Tut Premium I have used your premium service before and you always deliver the goods!

I studied ENCOR v1.1 Questions – Part 1 to 4 and all the labs. All the questions seems from PART 1 mostly and I didn’t seem to get any new questions if I did they weren’t difficult.

Labs were
Rapid PVST+ and LACP Sim
VRF Configuration Sim
eBGP Neighbor Sim
OSPF & Prefix-list Sim

ALL the same except for the LACP the port-channel was setup as an access port. On the Prefix sim route 0.0.0.0/0 le 32 was already in the configuration.

THANKS Again and good luck to everyone else!

Passes the exam with flying colours. Everything here appeared on the exam except for the question (3*5)% as what @Hey mentioned.

Big Thanks to DigitalTut! All the best to upcoming testers 👍

1. what is the result of this python program (3*5)%

Python modulo operation is used to get the remainder of a division. The modulo operator(%)
a % b
Here, a is divided by b, and the remainder of that division is returned.

Passed the exam on 10 December.I got 91Q including some experimental questions. Around 10-15 questions were unseen. I got 4 lablets and all were from digitaltut.

Rapid PVST+LACP
eBGP
OSPF BDR Sim 2
VRF Sim

There were some present on digitatut but they were either rephrased or with unseen answer choices. I studied all parts 1-11

Got passed today.

I got 91 questions with 4 labs. almost all questions are from digitaltut. I got 3 up to 4 new questions that are not on digitaltut.

The labs are 2 eGBP labs with the same topology and different AS numbers, vrf lab, and LACP.

The first eBGP lab AS numbers are 100, 200, and 300, and the second eBGP lab AS numbers are 10,20, and 30. both of two tasks of the labs are similar and also similar to those on this site.

The vrf lab tasks are:
— Tunnel 0 is configured only with ip address, so i configured tunnel source
interface and tunnel destination IP address
—- Task 2 is similar to this site
LACP tasks:
The first task asks the spanning tree to support 32-bit value –>” spanning-tree
pathcost method long”
The second task was about EtherChannel.

I studied ENCOR v1.1 Questions – Part 1-4 and Part 4-11 and Encore 350-401(expired) and all the labs.

Passed a test on Dec 2nd, 2023.

About 10 – 15 questions like never seen from here.

91 Questions in total, including 4 sim labs :

OSPF DR & Summarization Sim
Trunk UDLD & LACP Sim
eBGP Neighbor Sim
VRF Configuration Sim (no option 2 for me. interface Tunnel 0 had no tunnel source & destination in both R10 and R20. You have to add both tunnel source and destination)

Failed the test on 11/12.
About 10 – 15 questions like never seen from here.
Lab were from here. Admin can i know when you will update the latest sets of questions?

Just took the exam today, 91 questions 4 SIMS (VRF, Rapid and LACP,eBGP,OSPF DR BDR Sim 2)
I just studied Encor 1.4 (v1.1) Part 4-11 (OLD)
out of the 91 questions only half of it were the ones I familiarized. better study ENCOR 350-401 (expired).

The only difference with the sims is at was asking me to configure spanning tree to support 32-bit value?
spanning-tree pathcost method long

good thing I was calm and understood some of the questions. That would not end well if I panicked.heheh

Good luck and thank you digitaltut.

Passed the exam today

91Q’s in total

–Labs–
OSPF DR & Summarization Sim
Trunk UDLD & LACP Sim
eBGP Neighbor Sim
VRF Configuration Sim

studied Questions
Part 1 to 11
ENCOR 350-401 (expired) questions
practiced composite questions
all the labs

10-15 new questions but if you study the v1.1 syllabus can answer them as well

All the best to upcoming testers and thank you digitaltut.

Guys, passed last 13th.
4x labs:
eBGP Neighbor Sim
VRF Configuration Sim
Trunk UDLD & LACP Sim
OSPF DR BDR Sim
83 questions: maybe 50% questions that you can find here and 50% new ones.

Studied: part1,2,3,4

I passed the exam on DEC 16
87 questions and 4 labs

eBGP Neighbor Sim
VRF Configuration Sim
Trunk UDLD & LACP Sim
OSPF DR BDR Sim

all material here is valid, i studied V1.1 four parts and also parts 1-11 plus old encor part.
thank you again DIGITALTUT

Just finished my exam 5 minutes ago and passed thabk god! Even though i skipped one LAB by ACCIDENT LOL. Just want to share the new question i got:

1
About EEM APPLET wherein it ask you how to run the TCL script to store the BACKUP CONFIG:
I think the answer is *eem 2.0 write_backup.tcl

2
About HyperVisor type 1
ANSWER: …runs on top of baremetal

3
About EEM with IP SLA tracking
ANSWER: …track 10 down

4
About PYTHON with modulo operator (3*5)%
I think the answer is 0? Since no error is part of the choices

Thanks a lot digitalTut for the helping hand.
Been studying for 6months and digitaltut is just a cherry on top
To prepare myself fully with an exam worth 200$ lol

For number 4. I think its 1 not 0
CHOICES: 7, 7.5, 1, 0

They will have updated questions these days…. since I am going to take the exam soon!!!!

Hi hi, Where can I download the questions to these? Thanks!

Passed the exam an hour ago, I got no new question
91 questions 4 Labs inclusive; Vrf IPsec,ospf prefix list,trunk etherchannel 2Labs.

I studied old version 4-11 and new version 1-4
I studied the OCG cert guide and did many labs for 7 months before doing digital tut for just one month.
It is easy when you understand the technology and not just cramming

Just now finished the exam and couldn’t make it. :( 4 Labs are the same but many many new questions mostly from sd-wan related.

Hi Admin DigitalTut,

When you will update new set of questions? Thanks

pass the test ! previously i have taken ccna with digitut passed that ! now i took ccnp with digital tut passed ! 100% great service ! 91 q + 4 lab .

can you add amazon and azue dumps ?

Please also add fortinate dumps, next i’m going to take SD-wan test after studing

I took the test today and passed with no problems!!!!

Thanks for everything!

I passed the exam yesterday.

I think I got 10 similar or new questions

Lab are
Rapid PVST+ and LACP Sim,
VRF Configuration Sim,
eBGP Neighbor Sim and OSPF & Prefix-list Sim

I studied ENCOR Q 4-11 and ENCOR v1.1 Q 1-4
And I also studied the questions within ENCOR 350-401 v1.1 tab

I recommend you to take the exam after studied all the questions.
Questions were submitted in every area I studied

Good luck

Pass thnks guys most of the qs are same but i got 10 new qs but all the laps were same

I passed the exam.
Labs were
OSPF DR BDR
TRUNK ETHERCHANNEL SPANNING TREE METHOD PATH
EBGP
Tunnel with VRF
I got questions from here and like 10 or 15 different but you can make it if you read the questions carefully and analyze the answers. I am happy that I made it.