Share your ENCOR v1.1 Experience

I could be wrong about this, but in my opinion January to say mid February is the best time to take the exam. It’ll be hard to predict anything after that for a good while, with the new changes coming in March. I’ll be taking it next week, fingers crossed most of the questions will be from 1-7 and the labs don’t glitch.

Good luck to those who are taking it in this month.

I have got mine on sunday and i am not 100% confident but we will see. Quite terrifiying doing the revising atm. I will share my experience with you guys.

took my exam today and passed. q&a here are still valid.

for the acl and copp, instead of eigrp, i got ospf for task 1.

for ospf summarization, i got /20.

there’s a question abt wifi interfence, choices are fish tank, mirrored wall

netflow sim 2
vrf sim 2
ebgp sim 2

cant remember others but i got 6.

there are maybe 1-2 questions on automation

i just studied v1.1 and part 4-11

@switch, did you get questions from part 4-11?

Passed yesterday 6 labs took me 1hr 15 mins to complete labs so only short time for questions, felt rushed at end. new questions 4
VRF2
BGP2 – check AS use address family
OSFT sum 2
Netflow2
access and COPP telnet
LACP and Root bridge

Did you study the old questions parts 4-11?

I passed today.
If I study ver1.1 and the lab, I’ll be fine.
Thanks for digitaltut.

Be careful of Chinese companies like 5xxlab and chixxxdump.
I used to trust them, but this time I paid $300 and got scammed.
They also encourage people to take the exam on their behalf.
They state that they will refund the purchaser’s money if the exam fails, but they continue to ignore this.

Passed yesterday guys, again 6 same labs that we have been having, questions from V1.1 and some few that i was not aware of them.

Suggestion: Master the labs and READ what they require. Do not memorise and copy paste we are engineers :)

Good luck everybody

— CCNP CORE — Compelted — CCNP ENARSI –> Loading

Does anyone know what version of iOS they have in the labs, new or old version?

Did you study the old questions part 4-11?

Passed. Thanks Digitaltut.

Netflow Sim 1 – threw me off since everybody’s been getting Netflow Sim 2 lately. Also threw me off that the router was configured with an existing flow exporter and monitor just like in Sim 2. It was not clear which PC was the collector. The switch description did not mention.

LACP & Root Bridge – the port channel was two links, not three. Second task only asked for vlan 10 only.

eBGP Sim 2 – AS numbers and loopback numbers were different. R1 was on the left side.

OSPF Summ Sim 2 – almost the same as here. Second task asked for /19.

ACL & Copp – Task 1 – OSPF. Task 2 – Telnet. ACL number was different.

VRF Sim 2 – The router and switch were on the left side. VRF FINANCE was pre-configured.

I got around 10 questions that were not part of 1-7. I did not study 4-11 so I don’t know whether they were old or new.

@Silvester new version, in VRF LAB you need to use VRF definition Finance instead of ip vrf Finance. in the ACL and CoPP LAB you need to use ip access-list extended 150 instead of access-list .

What did you have to configure in the Netflow SIM? only the monitor on the interfaces?

Did you you just pick a PC and configure it as the exporter?

What was the NETFLOW task they expected you to configure?

Also anyone else who can answer my question about the collector IP. I’d be very grateful. My exam is tomorrow.

hello Rick,
good luck and please share your experience after the exam!

Thanks. I will. I just wish someone would answer my question about the Netflow task.

The Netflow Sim 1 was the same as here on difitaltut.
I picked PC2 I believe which is what’s here on digitaltut as well.

Thank you.

I passed. Most of the questions were from v1.1, about 3 from the old parts 4-11 and two questions were not found in either, but they were easy.

The labs are similar to what you’ll find here but with a few changes like AS numbers, telnet instead of icmp for CoPP etc. The labs I got were LACP./Root, eBGP with address family, VRF2, Netflow 2, CoPP with telnet and OSPF summarisation 2 with /16.

Remember to read the tasks carefully. For instance, for SLA you might not be asked to configure icmp to PC1 but to a loopback on the switch, and for CoPP you might be asked to police traffic from a single host, not the entire network.

Thanks to everyone who has contributed here with their valuable comments. Please remember to continue to do so for the benefit of others who have yet to take the exam.

Thanks to digitaltut for their valuable resources and that too at such an affordable cost.

Good luck to all those who plan to take the exam. If you study the material available here and understand what you’re doing in the labs, you’ll pass with no trouble at all.

Guys can you tell me how many questions are there port 4 to 11 and if these are still valid

@John. It really is hard to say for certain, but it’s a small number. As I said in my comment above, I only got abou 3 to 4 from the old parts but you might get more. Generally I’d say just v1.1 parts 1-7 are sufficent to pass, but I was paranoid so I did everything.

Passed! this sites still valid I think I have 2 or 3 unfamiliar questions thou I only run thru to v1.1.

6 labs, my first 6 questions are all labs. lol Some changes on the details so make sure to understand the concept.
– NetFlow Sim 2
– Access-list & CoPP Sim
– VRF Configuration Sim 2
– LACP & Root Bridge Sim
– eBGP Neighbor Sim
– OSPF Summarization Sim

Thank you digitut.

i can see answers on the website. Where are the questions ?

My CCNP ENCOR certification is set to expire in March. Do I need to retake the ENCOR exam to recertify, or will passing the ENARSI exam alone be sufficient to renew my ENCOR certification?

Any core exam (e.g: ENCOR, SCOR, AUTOCOR, etc)

Two concentration exams of your choosing in the Enterprise track (e.g ENARSI + ENSDWI)

Passed yesterday(1.28).
I studied ENCOR v1.1 Questions – Part 1 ~ Part 7 and Lab Sims (above-mentioned)

Thank you, Digitaltut.

For VRF lab, can old commands be asked in exam or do we only need to know the new ones?

I passed. Thank you, Digitaltut.
I got 6 labs, around 3 new questions, and 4 from the old parts 4-11.
– NetFlow Sim 2
– Access-list & CoPP Sim
– VRF Configuration Sim 2
– LACP & Root Bridge Sim
– eBGP Neighbor Sim 2
– OSPF Summarization Sim 2 got /17

How can I get the dumps from this site, pass it with 100% assurance. I am planning to give the ccie ENCOR written exam in next week.

Pass the exam today Feb 2, 2026. valid 1-7 plus lab.

passed, 54 MQ and 6 LABS…almost 97% from this dump part 1- 7..if you study all labs and 1 – 7 you would pass.

labs were

– NetFlow Sim (with flow exporter)
– Access-list & CoPP Sim
– VRF Configuration Sim FINANCE
– LACP & Root Bridge Sim (root primary for VLAN)
– eBGP Neighbor Sim (with address family ipv4)
– OSPF

@FU please send to me valid encor questions

Passed. Appreciate this site exists and can confirm content in part 1- 7 is still valid.
Had couple of new questions not seeing before and few from old section (8 in total but still good to pass).
One Q I recall was eBGP between two routers over two links with Loopback IP in neighbor command. They asked for missing cfg to allow both links being used and not reflect to one of them being down. I found to be missing “Update source lo0” and assumed main idea was “maximum-paths 2” but options were tricky. None of them got combination of both.

Labs below were as here I only had issue with extended AL for EIGRP. No matter what “5 permit eigrp any any” was not appearing in sh run. I accidently removed AL so I had to configure it again. It worked after all, but I might be penalized for removing it? Either way for me it was a bug as in real world that command is accepted and showed in sh run.
– Access-list & CoPP Sim
– NetFlow Sim (with flow exporter) + HTTP GET
– VRF Configuration Sim FINANCE
– LACP & Root Bridge Sim (root primary for VLAN)
– OSPF Summarization Sim 2 got /18
– eBGP Neighbor Sim (with address family ipv4)

passed, 54 MQ and 6 LABS only Questions past 1-7 and 5 new questions

labs

– NetFlow Sim_2
– Access-list & CoPP_Telnet
– VRF Sim_2
– LACP & Root Bridge Sim
– eBGP Neighbor Sim_2
– OSPF_sim_1

@Nw dump is here you can buy and you will pass 100%

I successfully passed the Cisco ENCOR 350-401 examination yesterday.
The exam has 60 questions, 7 LABs (all LABs from here are correct — some has different IPs or networks) and 53 questions (about 10 drag ‘n’ drop). The exam has about 7 new questions.

Questions is here:

Refer to the exhibit.

How should the programmer access the list of VLANs that were received via the API call?
A. VlanNames[‘response’]
B. VlanNames[0]
C. VlanNames[‘Vlan1’]
D. list(VlanNames)

Answer: maybe B or D

Drag and drop the wireless elements on the left to their definitions on the right.
Select and Place:

Answer:

Which two southbound interfaces originate from Cisco DMA Center and terminate at fabric underlay switches? (Choose two)
A. ICMP: Discovery
B. UDP 67: DHCP
C. TCP 23: Telnet
D. UDP 6007: NetFlow
E. UDP 162: SNMP
Answer: A,E

How does SSO work with HSRP to minimize network disruptions?
A. It enables HSRP to elect another switch in the group as the active HSRP switch.
B. It ensures fast failover in the case of link failure.
C. It enables data forwarding along known routes following a switchover, white the routing protocol reconverges.
D. It enables HSRP to failover to the standby RP on the same device.
Answer: D Or B

Drag and drop the characteristics from the left onto the orchestration tools that they describe on the right.

Answer:

What are two methods of ensuring that the multicast RPF check passes without changing the unicast routing table? (Choose two.)
A. disabling the interface of the router back to the multicast source
B. disabling BGP routing protocol
C. implementing MBGP
D. implementing OSPF routing protocol
E. implementing static mroutes

Answer: C,E

Which method is used by an AP to join HA controllers and is configured in NVRAM?
A. stored WLC information
B. DNS
C. IP Helper Addresses
D. Primary/Secondary/Tertiary/Backup
Answer: A OR B

i have pictures from drag n drop but i cant post it here….

@FU
Do you mean needs to learn all question from part 1-7 ? they are total around 750.

All those questions are in the dumps. Probably not in parts 1-7 but in the old parts and in the questions listed at the side by topic names.

@Serafino000, can you please share the photos to slimguy_234 at yahoo dot come please? thanks.

all the question given by @Serafino000 are all in the dumps. I’ll be taking my exam next week hopefully no new question will be added.

Passed the exam. I just studied v1.1 part 1-7. Got around 10 mcqs that I was not familiar with. They might be in old encor questions. Lab were exactly the same, so be thorough with all these provided labs. Thank you so much digitaltut. next step ccnp

Passed the exam.
I had 6 labs :
eBGP Neighbor SIM 2 : same
ospf Summarization sim 2 : same with /18 for Summarization
Access-list & CoPP Sim : same, i had the SSH for the last task
Vrf configuration SIM 2 : same lab but it was the router on the other side
Netflow SIM 1 : same lab
LACP & Root bridge : Task 1 : i couldnt use the command interface range, so i configured each interface. For Task 2 : it was not the same vlan for the spanning-tree

I had 54 questions.

I only did a lot of times the medium composite with 50 questions and i feel like i had more than 20 news questions.

I think that if you are able to complete the 6 labs and have more than 90% on the medium composite a lot of times. You will pass the exam. I studied the exam during 6 weeks and i was fine.

Good luck and thank you digitaltut.

Passed the exam yesterday. I just studied v1.1 part 1-7 + Labs v1.1

Congratulation :)

How many drag and drops?

what were the dnd questions?

can anyone share the new-old questions that are not from parts 1-7 ?

If you’re taking this before March 19, make sure you hit the virtualization, SD-Access, SD-WAN and automation hard. I saw a lot of questions that weren’t on ENCOR v1.1. Parts 1 – 7. Netflow was EIGRP and has extra devices.

I passed exam. I had 6 labs. There were some questions from old part. They were only 2-3 new questions but If you know how to answer practice questions here. There shouldn’t be any problem. I was studying the labs directly building from myself instead of practicing or extracting the files here. It helped a lot. Thanks Digitaltut!

LACP& Rootbridge
OSPF summarization 2
VRF sim 2
ACL& CoPP
Netflow 1
BGP address family