Share your ENCOR v1.1 Experience

HI guys do you know where you can get the lab

You need to go premium member and get access premium.. after that you can get questions and labs .. EVE Labs and explanations about ..

Hello guys, I passed the exam(2026.02.20) the dumps are still valid, i have 1 question which i didn’t see here at all, labs were: vrf sim 2, netflow sim 2, ospf sum 2, lacp&root bridge sim, bgp sim 2, acl&copp with telnet. plus 54 mcq.

Hi everyone,
Do you have any tips on how to study for the lab section of the exam?
I’m taking my exam on February 24th, and I’m not sure how to prepare for the labs.
If anyone has already taken the exam, could you share what kind of lab topics usually appear? That would really help me focus my studies.

Thanks in advance!

I passed today!

All the questions from v1.1 are valid! Only about 5 questions came up that I hadn’t seen, but if you study v1.1 you’ll pass! Most of the questions focus on wireless, SD-WAN and Automation!! Study these topics a lot! Total 60 Questions and 6 Labs!

The labs I took were the following:

eBGP SIM2 – Similar lab (BGP with “address-family”) Different AS Numbers (65100, 65200 and 65000 if I’m not mistaken)! All networks to advertise were /32!

OSPF SIM2 – Similar, had to configure OSPF on R30, had to use “network command” and the summarization was with /17 in area 50!

LACP – Similar, it was port channel 10 (I set a “default” on interfaces e0/0 -2) before configuring the trunk and it was possible to use the “range” command to configure the interfaces! Priority VLAN 10, 30, the same here.

ACL & CoPP – Similar, ACL on R10 was number 150 and the CoPP configuration was ICMP. (The Lab does not provide access to PC2 for validation!

VRF – Similar, VRF FINANCE was already configured and in uppercase! It was only necessary to proceed with the Tunnel0 configurations and static routes within the VRF!

NetFlow SIM2 – Similar, in the SW1 configuration, monitor session 5 was requested (if I’m not mistaken) source interface of PC1 not VLAN! The rest was the same!

Good luck to everyone, it’s well worth acquiring premium access, everything is valid and it’s a good cost-benefit to avoid losing the $400 for the exam! However, you have to know the concepts, don’t memorize the answers, but understand why the correct option is the one you choose; it’s easier to learn the reason than to memorize almost 500 questions!!)

Passed today

Passed today. MCQ are from v1.1 parts 1-7 and from old ENCOR.
Labs are netflow 2, acl&Copp, eBGp address family, OSPF summarization with network command,LACP & Rootbridge, VRF Finance.

I wanted to share that I just passed my CCNP ENCOR exam! A huge thank you to the 9Tut community for the invaluable resources.

Regarding the exam content, I found it very consistent with the current materials. Only about 5 questions were different from the V1.1 dump. As for the labs, here is what I encountered:

eBGP SIM2

OSPF SIM2

LACP

ACL & CoPP

VRF (Finance)

NetFlow SIM2

The labs were very similar to what is discussed here. Thanks again for the help in achieving this milestone!

Passed on 20th of February. I was surprised about the importance of sims. I got all of them right, but only 50% of questions but still passed.

eBGP SIM2
OSPF SIM2
LACP
ACL & CoPP
VRF (Finance)
NetFlow SIM2

Ghost_br and John3344 , can you share your dumps?

Can someone give tell me how many question we have in this dump (Premium membership) for Exam?

Can you please share if there were any drag grop questions?

Any new exam takers? Are there any new questions or labs?

@Pasa around 700-800

Hello guys, if you took the exam recently or planning to take it today, please share your experience, I am planning to take it on Wednesday but will re-schedule it if I don’t see/find any recent feedback.

can you share some of the questions?

Managed to pass in the last few days. Ospf summarisation /17 with network command. Acl & Copp summ with Icmp. NetFlow with flow monitor & source vlan on monitor session. VRF Sim 2 with Finance vrf already pre-configured, could only ping from Sw11 to end of the tunnel, couldn’t ping to other switch. eBGP2 same but had a x.x.x.17/20 ip address as a network to advertise. LACP just 2 interfaces in port channel, had to do no shut to bring up the tunnel. You could just learn from Encor 1.1 part 4-7 on the questions and be ok, all relatively new. There was a new root guard / bpdu drag n drop question with 2 core switches & 2 access switches, 7 gaps to fill which was tricky. Gl to all new takers.

@McFly What do you mean by all relatively new?
“You could just learn from Encor 1.1 part 4-7 on the questions and be ok, all relatively new”

Hi I am planning to give my exam on 10 of March kindly share your experience

Hi I am planning to give my exam on 14th of March kindly share your experience

Encore v1.1 ends March 18th 2026. They are stripping out the wireless into another cert track. Encore v1.2 begins March 19th 2026. I really hope the only change is they remove the wireless questions, but I doubt it.

@Anon.. usually for minor version updates v1.1 to v1.2 for example will not change significantly, probably will add a few questions about AI to replace the wireless questions. All other questions and labs are more than likely going to remain.

@Anonymous…Thanks for that info. I was very concerned when I stumbled across that post that it would be a complete overhaul. Now I will sleep a little better tonight. Thanks again!

I passed the exam today but there were at least 10 questions that I haven’t seen before… I only studied v1.1 Part 1 – 7, so not sure if they were from the old question pools or if they are actually brand new questions…
Total 54 questions
6 Simlets: VRF Sim 2, eBGP Neighbor Sim, OSPF Summarization Sim, LACP & Root Bridge Sim, NetFlow Sim 2, VRF Configuration Sim 2.

Thank you DigitalTut, planning to take ENSDWI at some point this year, I hope you guys can update the questions for that one as well soon.

yesterday, I’ve passed ccnp encor exam 350-401 so please study all version 1.0 and 1.1.

firt step 6 labs (very similar didigatul preparation)
eBGP neighbor
OSPF summarization area 50
LACP & root bridge sim (change PO number 12)
VRF sim 2 (in exam lab we’ve destination server on task for netwflow)
Netflow 2 sim (configure http get)
ACL & CoPP (access-list ssh version)

second step
54 questions (here i seen 4/5 old questions)

many thanks Digitaltut

Passed my exam today. 8 Labs and 60 question. all the LABs and questions here are valid. i would say if you can pass Composite Quizzes in practice most of the time or get above 85% you be fine. labs take alot of time so best practice them quite a bit to save time. I had just 30 minutes left to do my question once i finished the labs. Thanks Digital Tut

@engineer can you please recall the 8 labs?

Took the exam this morning – had 6 simulations and 56 other questions. The last simulation of extending vrf CORP failed to respond to show run or config terminal – so I skipped it hoping I got the first 5 sims and at least 95% of the MCQ and drag and drop. Passed regardless of the last simulation. Thanks Digitaltut

@Digitaltut – Is the exam questions changing after March 18 2026 ? When when will the new questions be updated for V1.2 ENCOR under premium ?

I took the exam a couple of days ago.
The simulation questions were the same as the ones everyone listed here.
For some reason, the BGP lab asked me to configure a peer group. I think I didn’t do well on task 2 for VRF. However, I passed, so I realized it’s important not to give up until the end. Thanks, Digitaltut.

I replied same config of sim on router 1921. ******************************
Please type configuration commands here:

* Task 1
On R1:
R1(config)#
router bgp 100
(1)
R1(config-router)#
bgp router-id 10.1.1.100
(2)
R1(config-router)#
neighbor 209.165.200.226 remote-as 200
(3)
R1(config-router)#
neighbor 209.165.202.130 remote-as 300
(4)
R1(config-router)#
address-family ipv4
(5)
R1(config-router-af)#
neighbor 209.165.200.226 activate
(6)
R1(config-router-af)#
neighbor 209.165.202 130 activate
(7)

* Task 2
On R1 (under “address-family ipv4”):
R1(config-router-af)#
network 10.1.1.100 mask 255.255.255.255
(8)
R1(config-router-af)#
network 209.165.201.0 mask 255.255.255.248
(9)
R1(config-router-af)#
network 209.165.201.8 mask 255.255.255.248
(10)

Save configuration on R1:
R1#
copy running-config startup-config
(11)
Submit
Result:
Statement 7 is not correct! ————————————- sim looks like is not working.
********************************************************************************************************************************* TEST 1921 LINES to learn **********************************************
Spoke1921_der#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Spoke1921_der(config)#router bgp 100
Spoke1921_der(config-router)#bgp router-id 10.1.1.100
Spoke1921_der(config-router)#neighbor 209.165.202.130 remote-as 300
Spoke1921_der(config-router)#neighbor 209.165.200.226 remote-as 200
Spoke1921_der(config-router)#address-family ipv4
Spoke1921_der(config-router-af)#neighbor 209.265.202.130 activate
% Specify remote-as or peer-group commands first +++++++here dont let me type by error, but appears in sh run later.
Spoke1921_der(config-router-af)#neighbor 209.265.202.130 activate ?

Spoke1921_der(config-router-af)#neighbor 209.265.202.130 activate
% Specify remote-as or peer-group commands first
Spoke1921_der(config-router-af)#do sh run
Building configuration…

Current configuration : 1949 bytes

!
router bgp 100
bgp router-id 10.1.1.100
bgp log-neighbor-changes
neighbor 209.165.200.226 remote-as 200
neighbor 209.165.202.130 remote-as 300
!
address-family ipv4
neighbor 209.165.200.226 activate
neighbor 209.165.202.130 activate
exit-address-family
**************************************************+ just try to understand, learn and memorize, in router 1921 dont let me type

neighbor 209.165.200.226 activate
neighbor 209.165.202.130 activate

but after sh run the configuration

address-family ipv4
neighbor 209.165.200.226 activate
neighbor 209.165.202.130 activate

appears, I will memorize after understand the request of lab and check with sh run in my lab with tshoot comands. show ip bgp summary – sh ip bgp – sh ip route.

If someone have a telegram group share link, I try to find my compas Vicente & Lionel…

Passed athe exam today! Thank you for all the contributions. Thank you, Lord JESUS Christ 😇 All glory to God! 💯

6 Lablets
– Access-List & CoPP (version 3)
– LACP & Root Bridge (diff port-channel #)
– NetFlow, IP SLA, SPAN (monitor session from/to both PCs)
– eBGP Neighbor (config on R3, different AS)
– VRF Configuration 2
– OSPF summarization (no “network” command)

Passed my exam. I studied v1.1 only.

Those labs are still valid and it is about 10 new questions.

Do i need to study old ENCOR or only 1.1 that enough?

@el_vato – had the same symptoms – but using show run, the commands CLI were in place so I clicked on submit. One other observations, the CLI that shows up after one configures a switch or routers, Cisco adds other verbiage into the CLI.

@NXTO i currently use router 1921 to type the commands by example Netflow si7m 2, commands for sw 1 I used a sw 3560-CG for monitor session and packet tracer for ip sla 1.

I just study 1-7 v.1.1 and shared labs
eBGP SIM2

OSPF SIM2

LACP

ACL & CoPP

VRF (Finance)

NetFlow SIM2

I hope pass like others… Premium Member is the best way to recert…

Just got the exam and passed today. Huge thanks to @Digitaltut

6 Lablets and 54 questions (MCQ, Drag&Drop) Some questions I have never seen before like 8 to 10.
– LACP & Root Bridge between SW1 and SW2, access only in switch 1.
– Access-List & CoPP – SSH instead of ICMP
– eBGP SIM 2 – Address-family IPv4 – Different ASN # from the site, but the config is the same.
– OSPF summarization for VLAN 40 and /18 – Network command is not allowed.
– NetFlow SIM 2 – monitor session from/to both PC1 and PC2
– VRF SIM 2 – different IPs, but same config from the site.

https://learningnetwork.cisco.com/s/encor-exam-topics

19 March v1.2

Passed today!!!
same configuration labs, /16 area 40 for same network 10.40.50.0 /24, different AS 10 and 20 not 100 or 200, vlan 10 in lab session 10 or loopbacks change last octect or ip but same comfiguration. If you understand labs and study part 1-7 v1.1 will pass like me. some DnD. but I repeat try to resolve correctly labs. 6 labs 54 questions.

I think questions is not so important like labs, I was tired and response a lot wrong questions.

eBGP SIM2

OSPF SIM2

LACP

ACL & CoPP TELNET version.

VRF (Finance)

NetFlow SIM2

Memorize and practice configuration will help you a lot. You can memorize using a pen and notebook.

Muchas Gracias digitaltut!!! nos vemos en 2 años.:

Passed my exam. I studied v1.1 only. Most of the questions were from the 300 and up of v1.1, and about 10 new questions. 6 labs. Thank you 9tut and the community!
eBGP SIM2
OSPF SIM2
LACP
ACL & CoPP ICMP version.
VRF (Finance)
NetFlow SIM2

having challenges with booking the exam, anyone who once faced the challenge: The card selected is not accepted. Please help asap

Today I passed the exam.
The exam included 6 LABs and 54 questions. The LABs were exactly the same as the practice labs, with only a few tasks, IP addresses, or values changed.
1.OSPF Summarization Sim
2.eBGP Neighbor Sim 2
3.LACP & Root Bridge Sim
4.Access-list & CoPP Sim – Version 2 using CoPP_Telnet
5.VRF Configuration Sim
6.NetFlow Sim + NetFlow Sim2 – Mixed Task

For the 54 questions, most of them came from ENCOR v1.1 Last Part 4–7, and about 10 random questions were from older ENCOR question sets. Thanks Digitaltut

is there a page for the cyberops track cbrcor 350-201?

Passed today. Exam had the same 6 labs everybody saw. AS’s, ospf areas, and other minor details were different. on the IP SLA sim it was an http get request instead of icmp. Had about 5-6 new questions, only study 1-7 under 1.1.

Today I passed the exam.
The exam included 6 LABs and 54 questions. The LABs were exactly the same as the practice labs, with only a few tasks, IP addresses, or values changed.
1.OSPF Summarization Sim
2.eBGP Neighbor Sim 2
3.LACP & Root Bridge Sim
4.Access-list & CoPP Sim – Version 2 using ICMP
5.VRF Configuration Sim -(VRF CORP)
6.NetFlow Sim 1- Flow Exporter

For the 54 questions, most of them came from ENCOR v1.1. I didn’t notice any new questions. Study python scripts. Thanks Digitaltut

can you guys pls share valid encor dumps???pls help me out

can you guys pls share valid encor dumps here shimul.cse09 @ gmail . com???pls help me out

if you want the dumps pay the subscription, it is no expensive and take very good results

What are the chances, and how long will it take before valid dumps for v1.2 become available?

Hi, we passed today!!! We leart v1.1 part 5, 6 and 7.
1.OSPF Summarization Sim
2.eBGP Neighbor Sim 2
3.LACP & Root Bridge Sim
4.Access-list & CoPP Sim – Version SSH
5.VRF Configuration Sim -(VRF CORP)
6.NetFlow Sim 1- Flow Exporter