Share your ENCOR v1.2 Experience

@Crombo37 Regarding the “VRF Configuration Sim with tunnel security (IPSec)”, what was the requirement for the ipsec config, ikev1, ikev2? tunnel mode? make the ipsec tunnel and pass vrf traffic inside the tunnel?

I’ve had a few examiners inquire about the availability of a new VRF Configuration Sim with IPSec tunnel security. Is this a lab we currently have in the pipeline or available for use? I’d like to be able to provide them with a clear update. Thanks!

@Johndoe

You just have to secure the tunnel with IPSec profile which is already configured.

conf t
int tunnel 0
tunnel protection ipsec profile XYZ.

Just replace XYZ with the name on config.

Same VRF 2 lab with this add-on.

@Crombo37 .. oh that exactly like VRF Sim 1..

Hi guys, do you think questions will change a lot in a couple of months? Is it enough to study only questions below v1.2 or should I review all the questions available on this site?

Thx so much.

Hi all,

Any updates about ENCOR new version?

I just passed my exam very close. 6 Labs 100% valid, 53 questions. I was sure I not gonna make it because out of 53 i just saw 10 familar questions from v1.2 part 1-7. My passing score in composite quizz was alsways between 75-100 so not sure if there are just a lot of new questions or I had the luck to get always the same in Composite quiz (I only studied composite quizz + may 2nd update)

Unfortunately the exam nowadays feel like a mixed exam for programmer and sales person, not like a network engineer

@Juventino, Congratulations on passing your exams. can you please share your which labs you got. Thanks

Thanks, here are the sims:
Access-list & CoPP Sim
VRF Configuration Sim 2
LACP & Root Bridge Sim
OSPF Summarization Sim 2
NetFlow Sim
eBGP Neighbor Sim (not sure if v1 or v2)

Just pass my exam recently. The labs were similar to one in Digitut, with some minor variation
OSPF Summarization 2 /18 Summary
ACL COPP
NetFlow 2
EBGP Neigh Sim 2
LACP & Root
VRF configuration Sim

Unfortunately the majority of the mcq question are not in ENCOR v1.2 question pool neitier i recall in V1,1 question. Only small handful question were in pool
That was truly hard part.. Had to make ton of educated guesses from my knowledge .

For moment there i was worried i was going fail it.

Eitier way.. my advice for others at moment , Not rely too much on ENCOR v1.2 question .. Prehaps if possible wait for digitut update the question pool.

Hi digitaltut-support:
When can we expect the new questions vor the ENCOR v1.2?

@Rob

Was it VRF2 lab that just added the IPSec section from VRF1 lab, or was it the whole VRF 1 lab?

@Juventino, Could you please send me exam materials?
taddym666 at gmail dot com
Thanks.

Hi @Juvention and @Rob
Please send me dump files.
Michel.handerson at yahoo dot com

Congratulations on your success. Could someone send me the exam dumps?

ngargalakos at gmail dot com

@Cheetah
It was the whole VRF 1 Lab. Just some minor variation Mine has to had to add VRF CORP so you have redo the whole tunnel interface

@michel.handerson @sleepman
I got no dumps to share .. All my question revision i took from composite quiz on Digitut premium member

@Juventino @Rob,
Congratulation for passing the exam.
For Drag and drop questions, is it from v1.2 or new questions?

@Rob @sleepman @Juventino
Congrats on your exam…. please share which chapters the new questions are from.

Hi all,

Any updates about ENCOR v1.2 version?

Hi everyone, I have my exam scheduled for the 12th of this month. I would like to know if the questions cover everything from Part 1 to Part 7 here? If anyone has taken the exam recently, could you please share your experience? Also, is it normal to see about 10-15 different or new questions?

I’m planning to perform the exam , latest July, can you share the dumps?
Is there any recommendations about the study?

Hey Folks!!

Just walked out of the exam center with a PASS. But let me give you all the full run down.

First 6 labs were on target with the website and if you actually labed them and understand the ask, you will spend maybe 25 minutes on all 6.

I had the following:

Access-list & CoPP Sim
VRF Configuration Sim 2
LACP & Root Bridge Sim
OSPF Summarization Sim 2
NetFlow Sim
eBGP Neighbor Sim

My Advise : Practice all the variants until you can do it easily from memory – Dont just memorize it but understand it!

Now for the sad news

I studied both 1.1 and 1.2 questions, drilled all my wrong answers and did 10 of the 50 question quizes scoring 79 to 90. Guess what? I had MAYBE 4 questions out of 59 that i recognized. For each question, I had to pause and do a process of elimination. I was sweating bricks but I studied for this exam for 10 months prior to finding this site and I work in the field so things like VSS and ACLs,NAT were not difficult to answer. Overall I was able to make some really good guesses.

I had no questions on dumps, loads, NETCONF, RESTCONF – most of my questions were about SDWAN, SDACCESS, a few multicast, EEM, control plane vs data plane protocols.

If you’re hoping to memorize each question, you’re better of waiting for a new update. If you’re confident in your exam taking skills then take a chance on yourself.

Good luck folks!

@BigBaller

I wanna clarify a few things

1- You got NetFlow Sim v1, not NetFlow v2

2- You got eBGP Neighbor Sim, not eBGP Neighbor v2

3- Did you get questions from the newly updated questions (24 to 51) from part#7?

I have scheduled my exam this week, after seeing this post, I’m a bit shaky

@Dropout
oddly enough i had only 2 drag and drop.. They were JSON and EEM
@You know
The new question were mix of COPP, SDWAN fabric , automation
@Santos
sadly majority of question not even covered from Digitut part 1-7..

Hi Everyone.!

Some dumps are around 700 questions include. Is that enough to safe in the exam?

Have the questions been changed, and do we still need to learn the old ones? Is that true? Has anyone taken the test who can tell us?

@Santos
Good luck on your exam. Let us know how it goes.

Guys do you have any update since i have a exam on May 14?

Hello Guys,
Please help when you guys are mentioning “SIM2” or V2 what does it means.
Access-list & CoPP Sim
VRF Configuration Sim 2
LACP & Root Bridge Sim
OSPF Summarization Sim 2
NetFlow Sim
eBGP Neighbor Sim

I am unable to find any simulation on this site. Is there a seperate subscription ?
Thank you

@Cheetah – yes they were mainly the V2 variants of the labs but my advise is to master both and all options for example in the CoPP and ACL you should know how to write an acl for ssh, icmp , telnet. If any thing changes you want to be confident.

“3- Did you get questions from the newly updated questions (24 to 51) from part#7?” No, i didnt recognize many questions but the topic and concepts are the same. Maybe 4 questions.

I beleive the entire exam bank has changed as I didnt recognize more than 5 questions. Luckily i studied both 1.1 and 1.2 and learned why each answer could be right or wrong. That will help you more vs just memorizing answers.

@AAB you need to get subscription to see labs. Version 2 is updated version of old SIM like VRF and VRF2,vrf is old and vrf2 is updated SIM

Too late now. My exam is tomorrow, I have read some posts looks like they changed the exam right before I was going to attempt it. I will update you all how it goes, can’t reschedule it so I will just go for it. I will update yall how it goes.

any update from the new exam? SOS help arigato kozaimas

@AAB Good luck on your exam. Let us know how it goes.

Hi everyone, I passed my exam today!
I encountered several lab tasks, including ACL_CoPP, VRF Configuration, LACP & Root Bridge, NetFlow, eBGP Neighbor, and OSPF Summarization. Although the general topologies were the same as the practice materials, there were slight variations in the requirements, such as different ACL numbers, protocol IPs, and other specific parameters.

I struggled a bit with one of the IP SLA tasks and ended up leaving it blank. It required using the http get command to verify a web server, which was a bit tricky.

Aside from the labs, there were 59 questions. To be honest, only about 25 of them were similar to the study materials I used. The rest were quite different, so I had to rely on my own logic and experience to answer them. It worked out, but it was definitely risky.

My advice: If you’re planning to take the exam soon, it might be better to wait a bit until the materials are updated. However, if you have solid experience as a Network Administrator—especially in Automation and SD-WAN—you can definitely pull it off!

I’ve PASS exam today!!!!
53 for choices
6 for labs

Netflow sim
Access-list & CoPP Sim
VRF Configuration Sim
eBGP Neighbor Sim
OSPF Summarization Sim
LACP & Root Bridge Sim

Recomment to remember both v1 and v2 for lab

I’ve see new question for about 10 questions, but no worry .
Study hard , you will pass for sure!

Any update about the new exam? My exam is this month :(

@digitaltut
how long is going to take to add the new questions?

Passed exam. labs all same, just ip addresses, As numbers and process ids were slightly different. Dont worry about the new questions. Most were still from here, About 10-15 new ones, if you understand the questions and the answers for the existing ones just use same logic.

@john
thanks for sharing, do you remember which section of question you got the most?

Passed my exam today.
Same Labs as everyone is mentioning.
NETFLOW LAB
VRF
OSPF
BGP
COPP
Port-Channel

Couple of drag n drops (Anisible, puppet) and Declerative / procedural
A lot of SD Wan questions + Radius/TACAS+ type questions. Some programing questions including phyton + JSON + API Calls etc. I dont have subscription so not sure if any questions were from question pool here.

Congratulations @ AAB and all those who passed. My Exam is in 3 months approx so I’ve just started learning the concepts. Though I have experience, learning here is a great advantage!

Hi everybody
Today I passed an exam , DIGITALTUT many thanks to you !
6 LAB’s from Lan Sims v1.2 , the tasks were the same, but read tasks carefully ! different ip addresses, numbers of routers, etc.

vrf configuration Sim 2
Access-list& Copp sim ….. version SSH
eBGP neighbor Sim 2
LACP & root Bridge Sim
NetFlow Sim 2 …. ip sla ICMP-echo
OSPF Summarization … using network

and 53 questions:
some questions weren’t included in v1.2
my personal opinion is that v1.2 was enough to pass successfully of course not sure
I’m sorry, but I only remembered 3 questions

one is in version 1.0 part 5 question 16 drag and drop VSS architecture

and

Question 44 under version 1.1 part 3

How does a WLC achieve stateful switchover for APs and clients?

A. The active WLC establishes a CAPWAP tunnel to the AP, and the standby WLC establishes a LWAPP tunnel to the AP
B. The active WLC establishes a CAPWAP tunnel with the AP, and the standby WLC copies the AP database and the client database from the active WLC
C. The active WLC establishes a CAPWAP tunnel with the AP and standby WLC to share the AP database information
D. The active and standby WLCs establish separate CAPWAP tunnels to the AP

Answer:B

also
Question 4 from AAA question

Refer to the exhibit.
aaa new-model
aaa authentication login authorizationlist tacacs+
tacacs-server host 192.168.0.202
tacacs-server key ciscotestkey
line vty 0 4
login authentication authorizationlist
What is the effect of the configuration?

A. The device will allow users at 192.168.0.202 to connect to vty lines 0 through 4 using the password ciscotestkey
B. The device will allow only users at 192 168.0.202 to connect to vty lines 0 through 4
C. When users attempt to connect to vty lines 0 through 4, the device will authenticate them against TACACS+ if local authentication fails
D. The device will authenticate all users connecting to vty lines 0 through 4 against TACACS+

Answer D

Passed exam today! I’ve been using this site for years and always on point. A lot of material to cover so if you want to pass then really hit the labs hard and it’s all the ones everyone is mentioning here.

VRF Configuration Sim
eBGP Neighbor Sim 2
OSPF Summarization Sim with /17 summarization variant (advertise networks using networks command
LACP & Root Bridge Sim
Eigrp ACL + NetFlow Sim 2
Access-list & CoPP Sim version 2 with 8000 bps variant

make sure you know the python/Json syntax and EEM, how to read them. Some questions to drag and drop in on those.

Thanks all, the comment section helped a lot. now on to ENSARI

Passed my exam few days ago.
Labs:
BGP with adr-family
LACP with STP
VRF Finance
CoPP + SSH
OSFP + Summ /18
NetFlow with http

53q 6labs
There were about half of the questions new. I think the labs are the main ones that give the most points in this exam.

I have just taken today my CCNP ENCORE exam and unfortunately did not make it. I was not aware there are going to be 6 labs .
I struggled to complete all labs and end up leaving just no time to complete mcq. Labs I received were .

VRF Configuration
eBGP Neighbor using address -family
OSPF Summarization Sim with /20 for area 40 , advertising network and configuring ospf command
LACP & Root Bridge
EIGRP ACL + CoP policy to limit telnet traffic to 10000bps
NetFlow

Are these all labs available on digitaltute ?

I cleared exam and found that MCQ’s were mostly not covered by v1.2 (part 1-7) hardly 10-15 questions came from here out of 59 but TBH if u have done all labs perfectly then u should be easily cleared.
Netflow V1 [In task 1 they have already given Data collector IP so, I selected that IP instead of PC2 ip. In 2nd task mirror all communication to and from to that Data collector IP. In 3rd task was “http get”]. This lab was bit tricky and mix of V1 and V2. Task 1&2 from V1 and 3 from V2.

Access-list & CoPP Sim [SSH needs to configure]

VRF Configuration V2 [but need to config R11 instead of R22 and VRF Finance was already configured so, don’t need to reconfigure it, just start from tunnel interface. PC was disabled so, can’t verify from ping]

eBGP Neighbor V2 (Router was R3 instead of R1)

OSPF Summarization V2 [R30 needs to be configured instead of R20 and /18 summary route.]

LACP & Root Bridge Sim: [This config was bit tricky so, please pay attention. Only 2 interfaces e0/0-1 needs to be configured. I did whole lab but PO11 didn’t become trunk after running “show interface trunk”. So, I checked and found that eth0 port was SHUT so, I turned it up by “no shut” and removed” switchport access vlan 20” form both interface e/0-1] After doing this port channel came up as trunk interface.

Hi,
Can you tell me if this site has any interactive labs or SIMs where you actual log into devices?
If not, are there any free sits that allow you to do so to practice the interactive SIMs?

For the labs on the test, are there multiple-choice answers that accompany the question, or do they just want you to log into the routers and/or switches to make something work then hit submit?

Pass the exam. 59 questions, 6 of which are lablets. Thanks Digitaltut.