Share your ROUTE v2.0 Experience

@Pass93X do you have a link to download free vce player ?

@poo the other questions same kikavich all in one?

@route2np yes i would suggest study hard and pay more attention on each and every topics.
Thanks

Hi Guys,

Regarding PBR lab we have an update:(Update: We don’t need the last command:
“route-map pbr permit 20” to permit other traffic) So, which means if we are using this command we are still ok right??? I mean it’s an optional not mandatory right?

Tom, Did u use route-map pbr permit 20” command to permit other traffic for your PBR lab ????

@crazy Tom congratulations!!!!

Did you use any prep questions ?If possible can you share or provide link.also share your expeiance with all so if anyboday has exam more focuse on that questions and topics
i failed exam today and i planning to give exam on next week.

Thanks

@Mario

please wait for your exam feedback.

GARBAGE

@ leop9600 and group drive link

Hi All,
I’ve my exam re-sit next Thursday……..failed my last attempt miserably due to all the new content. Are the questions discussed on this thread close enough to the correct answers

I recognise some of the questions just finding it hard to believe them

Hi! Can we use show run for the exams? Thank you!

@Mosh

You can use Show Run for every Lab except one.

@Poo

Sorry to hear that.

I couldn’t use copy run start either. I tried……doesn’t work. Think it has been removed.

@Luigi

How did it go Luigi? Mario passed. We are getting together to go ride so go karts. Wanna come??

if . can’t use command copy run start for save configuration and what command we use ?

if . can’t use command copy run start for save configuration and what command we use ?

@Udom Ji

You don’t use any other command.

@Pazi, yes though they may look like they are directly connected, they are not. My husband is a CCIE and he explained to me that to achieve load sharing you have to pair with a loopback from a loopback so they are not directly connected, Meaning that the command update-source loopback x has to be used, and the neighbor x.x.x.x address used should also be the loopback of your neighbor router. This also means that you need to use either a static route or a dynamic protocol to get to the address of the loopback. hence the answer is B.

@Poo
so what your saying doing Kikavich and pg 148-152, enough to pass ?

Dear all

My exam is in 30 min from now,
I will share the update as soo as I finish.

Wish me luck :(

@Syn, If we can’t use copy run start, then how can we gonna save the configs?

Hi @Hallfawi, did you use copy run start?

Where do you enable RIPng?
a.interface config
b. global config
c. router config

Which is the correct answer??

@Mosh
you are not required to use copy run start or WR commands to save a config. the exam labs are designed to self-saved config once you finished.
hope this answers!

Best of luck @Hallfawi…….next update us pls!

@Anonymous
Where do you enable RIPng?
a.Interface Config
b.Global Config
c. Router Config
CORRECT: B which is Global Config

Guys, please provide the right answer? Thank you.

55. Which routing protocol searches for a better route through other autonomous systems to achieve convergence ?
a. Link-state
b. Hybrid
c. Path vector
d. Distance vector
Answer: A or C
56. What are the two benefits of BGP peer groups
a. support groups of paths
b. A configuration change can be applied simultaneously to all peers in the peer group
c. optimize backdoor routes
d. updated via multicast
e. each neighbour in a peer group can have different inbound BGP Policies
f. they use soft updates to minimize bandwidth consumption
Answer: B or F

sorry I mean B and F.

@Anonymous…..answer to 55 is certainly C (path vector)
@D Washington…..far to my knowledge RIPng can be configured both on router and interface level….please correct me if am wrong!

Thanks @ Roteontheway.

56. What are the two benefits of BGP peer groups
a. support groups of paths
b. A configuration change can be applied simultaneously to all peers in the peer group
c. optimize backdoor routes
d. updated via multicast
e. each neighbour in a peer group can have different inbound BGP Policies
f. they use soft updates to minimize bandwidth consumption
Answer: B, F
Please confirm if these are the right answers.

@Routeontheway it says how do you enable RIPng? Before you could do anything you have to go to Global Config Mode to initiate the process. The command would be: ipv6 router rip using config mode. Check This Link http://study-ccna.com/ripng/

question 56, BF is correct.
The major benefit you achieve when you specify a BGP peer group is that a BGP
peer group reduces the amount of system resources (CPU and memory) necessary in an update generation. In addition, a BGP peer group
also simplifies the BGP configuration. A BGP peer group reduces the load on system resources
by allowing the routing table
to be checked only once, and updates to be replicated to all peer
group members instead of being done individually for each peer in the peer group.

Which feature can mitigate fragmentation issues within network segments that are between GRE
endpoints?
A. PMTUD
B. ICMP DF bit
C. TCP Flow Control
D. TCP MSS

Answ: A or D ???

Hey guys, planning to start the CCNP Route studies. Please suggest the best and only book to study for the exam. I am thinking of “CCNP Routing and Switching ROUTE 300-101 Official Cert Guide” by Kevin Wallace published in 2014. Please let me know your inputs.

Where do you enable RIPng?
a.Interface Config
b.Global Config
c. Router Config
Answer A
Reference: https://www.cisco.com/c/en/us/td/docs/switches/metro/me3600x_3800x/software/release/15-4_3_S/configuration/guide/3800x3600xscg/RIPng_IPv6.pdf
“Enabling IPv6 RIP
Prerequisites
Before configuring the device to run IPv6 RIP, globally enable IPv6 using the ipv6 unicast-outing
command in global configuration mode, and enable IPv6 on any interfaces on which IPv6 RIP is to be enabled.
If you want to set or change a global value, follow steps 1 and 2, and then use the OPTIONAL ipv6 router rip command in global configuration mode.”

this all my ques that i dont surew about them…
1 RIPv2 how long a static route remains if the point to point interface is down..
a 30s
b 60s
c 180s
d 240s
answer is D ?
2. Which condition prevents the establishment of a DMPVN tunnel between two spokes?
a. HSRP is enabled on the spoke devices
b. IPsec is enabled on the spoke devices
c. the two spokes are behind different PAT devices
d. the two spokes have different tunnel keepalive settings.
ANSW: D OR C
3 Which routing protocol searches for a better route through other autonomous systems
to achieve convergence ?
a. Link-state
b. Hybrid
c. Path vector
d. Distance vector
answ :A?
4 Which three methods can a network engineer use to fix a metric based routing loop in the network.
a. Implement offset lists at network boundaries
b. Filter routes manually using distribute lists
c. Filter routes manually using prefix lists
d. Implement proper network summarisation on key routing points
e. Filter routes based on tags
f. Utilise root database filters
ANSWER:A,C,E or B C E
5. In which state do DR and BDR establish adjacency with each OSPF router in the network?
A. Init State
B. Exstart State
C. Exchange State
D. Loading State
ANS ?

Which feature can mitigate fragmentation issues within network segments that are between GRE
endpoints?
A. PMTUD
B. ICMP DF bit
C. TCP Flow Control
D. TCP MSS

Answ: A or D ???

36. Which three methods can a network engineer use to fix a metric based routing loop in the network.

a. Implement offset lists at network boundaries
b. Filter routes manually using distribute lists
c. Filter routes manually using prefix lists
d. Implement proper network summarisation on key routing points
e. Filter routes based on tags
f. Utilise root database filters

Answ: ABE or ACE????

My exam is tomorrow
I studied all question and labs

but not the drag and drop!

can someone tell me common drag and drops?

PLEASE HELP :)

THANKS

“RIPv2 how long a static route remains if the point to point interface is down?”
WHAT???

My exam is tomorrow
I studied all question and labs

but not the drag and drop!

can someone tell me common drag and drops?

PLEASE HELP :)

THANKS

Please help guys:

36. Which three methods can a network engineer use to fix a metric based routing loop in the network.

a. Implement offset lists at network boundaries
b. Filter routes manually using distribute lists
c. Filter routes manually using prefix lists
d. Implement proper network summarisation on key routing points
e. Filter routes based on tags
f. Utilise root database filters

Answ: ABE or ACE????

Answer to question 1 is D

https://www.cisco.com/c/m/en_us/techdoc/dc/reference/cli/nxos/commands/rip/timers-basic.html

Flushes routes = 240s

@Hallfawi

Good luck and hope you pass.

@Routeontheway
In my exam around 10 to 12 questions from this forum and I think new question that I never seen before and difficult to remember. I studied Kikavich which is from this forum I downloaded.study hard deft knowledge of each and every topic.
Thanks

Hi All,

please help to understand this questions answer

Router# show ntp associations
Address ref clock st when poll reach delay offset disp
~172.31.32.2 172.31.32.1 5 29 1024 377 4.2 -8.59 1.6
+~192.168.13.33 192.168.1.111 4 69 128 377 4.1 3.48 2.3
*~192.168.13.57 192.168.1.111 3 32 128 377 7.9 11.18 3.6
* Master (synced), # master (unsynced), + selected, – candidate, ~ configured

Which of the following is true?

A. Master is syncing and exchanging NTP packets successfully
B. Master is not syncing but exchanging NTP packets successfully
C. Master is not syncing and not exchanging NTP packets
D. All NTP packets are droped

Ans:- A is correct i’m not sure. please help me to explain it

Thanks

@Poo
Answer is A.
* in first collumn means syncing
377 means all packets exchanged

@Ghauri

Thanks for quick feedback.

@Halfawi
where r u buddy? We are waiting for your exam feedback.

@Poo
kikavich all in one plus question from this forum enough to pass the exam?