Share your ROUTE v2.0 Experience

@Ann Hi Bro,
sorry
I am looking your mail

@JAJA
hi bro thanks

QUESTION 690–>WHY D?
How can you minimize unicast flooding in a network?
A. Configure HSRP on two routers, with one subnet preferred on the first router and a different subnet preferred on the second router.
B. Set the router’s ARP timeout value to be the same as the timeout value for Layer2 forwarding table entries.
C. Set the router’s ARP timeout value to greater than the timeout value for Layer 2 forwarding table entries.
D. Set the router’s ARP timeout value to less than timeout value for Layer 2 forwarding table entries

Correct Answer: B >>> Should be D
learningnetwork.cisco.com/thread/117389

———————

QUESTION 743–> WHY B?
What is the output of the following command:
show ip vrf
A. Show’s default RD values
B. Displays IP routing table information associated with a VRF
C. Show’s routing protocol information associated with a VRF.
D. Displays the ARP table (static and dynamic entries) in the specified VRF

Correct Answer: A
——————————-

@abdulrahmansh
hi bro

QUESTION 693 –> WHY D?
Company is deploying a multicast applic ation that must be accessible between sites, but must not be accessible outside of the organization
Based on
A. FF00:/16
B. FFOE:/16
C. FF02:/16
D. FF08:/16
Correct Answer: C

ans must be D, same as q 543

Please can anyone give me username and password just for friendly

@Mosh…I did use the ip summary-address eigrp 123 10.2.0.0 255.255.0.0, and I was able to summarize down to just 2 10.2.0.0 networks, and i conformed with sh ip route. The question specifically asks to summarize down to only two 10.2 subnets, and this is the only mask that will accomplish that. I took the exam in the US. copy run start or write did not work. Good luck Mosh and everyone!

Hi, can anybody please share the links to download the labs

Hello @nneettwwoorriinngg

What is the difference between the Q 182 and 193, Why different answers? Please help I am trying to understand.

182. When unicast reverse path forwarding is configured on an interface, which action does the interface take first when it receives a packet?

Ans. D. It checks the ingress access lists.

193. What’s uRPF checking first when the packet enters the interface? OR
When unicast reverse path forwarding is configured on inter interface?

Ans, C. Route available in FIB ot it verifies a reverse path via the FIB to the source.

Hello @nneettwwrrookkiinnggg

QUESTION 428
Which three functionalities are specific to stateful NAT64? (Choose Three)
Ans
B. It requires either manual or DHCPv6 based address assignment for IPv6 host.
D. A state or bindings are created on every unique translation.
E. It conserves IPv4 addresses.

Choice B is wrong . REF to the table @ https://www.cisco.com/c/en/us/products/collateral/ios-nx-os-software/enterprise-ipv6-solution/white_paper_c11-676277.html

“Requires IPv4-translatable IPv6 addresses assignment (mandatory requirement)” listed under the Stateless NAT64, So I think So, F. No constraint is put the number of endpoints due to 1:N translation could be more appropriate choice instead of B.

@PL
focus August TAB Questions
need to pass
nneettwwrrookkiinngg@ gmail .com
contact with me

@nneettwwrrookkiinngg

SENT and email to you @ nneettwwrrookkiinngg@ gmail .com but bounced, could you verify your email id please

PL
fyi

nneettwwoorrkkiinngg @ gmail.com

@nneettwwoorrkkiinngg

QUESTION 693
Company is deploying a multicast applic ation that must be accessible between sites, but must not be accessible outside of the organization
Based on
A. FF00:/16
B. FFOE:/16
C. FF02:/16
D. FF08:/16
Correct Answer: C

ans must be D, same as q 543

FF02 is for link-local multicast and FF08 is for organization local multicast.

https://tools.ietf.org/html/rfc7346

@abdulrahmansh
Good job bro
Thanks for your help
I will fix it

anyone…can anyone submit an answer with valid proof.

A Customer asks its serve provied for VPN support for IPv4 and IPv6 address families. Which command enables a VRF that supports these requirements?
A. Router(config-vrf)#route-target 004:006
B. Router(config)#ip vrf CUSTOMER
C. Router(config)#vrf definition CUSTOMER
D. Router(config-vrf)#rd 004:006
Correct Answer: C?

3 passed this week using Maria’s dumps
drive.google.com/open?id=15LxO7JIEaIj_x6T14snLKbsI8J8RYkJQ
The VCE is awesome !

@nneettwwrrookkiinnggg

QUESTION 737
Refer in the exhibit. A packet capture indicates that the router is not forwarding the DHCP packets that it
receives on interface FastEthernet0/0. Which command needs to be entered in global configuration mode
to resolve this issue?
A. ip helper-address
B. ip DHCP relay
C. service DHCP
D. ip forward-protocol
Correct Answer: A

ip helper-address is configured on int mode , so either the q is wrong or the ans is wrong, and the correct ans is D

https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipapp/command/iap-cr-book/iap-i1.html#wp1776761080

Hi All

updated VCE

Sections
Networking – Valid-September = 195 Valid now

Networking – Questions DAY-1 = 96
Networking – Questions DAY-2 = 89
Networking – Questions DAY-3 = 89
Networking – Questions DAY-4 = 126
Networking – NEW Questions = 125
Networking – EIGRP & OSPF Simlets = 8
Networking – DRAG & DROP = 29

https: // drive.google.com/drive/folders/1Cf4MHTm8Qt5-_jYzJt6PXNy6b6YOBEx1

@networrrrrkkkkiiiiinnnnnnnnnnnnggggggggggggggggggggggggg

You did not remove duplicate question from pdf and VCE :S

Q556 & Q588 . Same Question

Q547 & Q702 . Same Question

Q394, Q504 & Q720 . Same Question

Q379, Q477 & Q658 . Same Question

Q422, Q495 & Q527 . Same Question

Q537 & Q672 . Same Question

@Ahmed,
don’t worry

I will check

Q556 & Q588 . Same Question

Q547 & Q702 . Same Question

Q394, Q504 & Q720 . Same Question

Q379, Q477 & Q658 . Same Question

Q422, Q495 & Q527 . Same Question

Q537 & Q672 . Same Question
__________________________________________________________________________________________________
QUESTION 702
Which two statements about the enable secret and enable password commands are true? (Choose two)
A. I both commands are missing from the global configuration,vtp lines use the console password
B. The enable secret command overrides enable password
C. The enable password command has a stronger encryption algorithm than enable secret
D. The enable secret commmand is bac kwards-compatible with more version of IOS
E. The enable secret and enable password commands must be used togerher
Correct Answer: AB
Section: Networking – Questions-August

QUESTION 547
what are the two correct statements about enable secret and enable password command
A. the enable password command has a strong encryption algorithm than enable secret
B. if both commands are missing from the global configuration, vty lines use the console password
C. the enable secret command is backwards compatible with more versions of IOS
D. the enable secret and enable password commands must be used together
E. the enable secret command overrides enable password
Correct Answer: CE
Section: Networking – NEW Questions

————————————————————————————————-
QUESTION 394
Which two commands must you configure in the calling router to support the PPPoE client? (Choose Two)
A. peer default ip address pool
B. bba-group pppoe
C. pppoe-client dial-pool-number
D. mtu
E. pppoe enable group
Correct Answer: CD
Section: Networking – Questions DAY-4
Explanation

QUESTION 504
Which two commands do you need to implement on a router to support PPPoE client?(Choose Two)
A. peer default ip address pool
B. MTU
C. bba-group pppoe
D. pppoe enable group
E. pppoe-client dialer-pool-number
Correct Answer: BE
Section: Networking – NEW Questions

QUESTION 720
Which two commands do you need to implement on a router to support the pppoe client? (Choose Two)
A. peer default ipaddress pool
B. mtu
C. bba-group pppoe
D. pppoe enable group
E. pppoe-clientdialer-pool-number
Correct Answer: BE
Section: Networking – Questions-August

————————————————————————————————-
QUESTION 379
Which two features does RADIUS combine? (Choose Two)
A. Telnet
B. Accouting
C. SSH
D. Authenticaiton
E. Authorization
Correct Answer: DE
Section: Networking – Questions DAY-4

QUESTION 477
Which two features RADIUS combine? (Choose two)
A. telnet
B. SSH
C. Authentication
D. Authorization
E. Accounting
Correct Answer: CD

QUESTION 658
Whcih two features does RADIUS combine?(Choose two)
A. authorization
B. authentication
C. ssh
D. accounting
E. Telnet
Correct Answer: AB
Section: Networking – Questions-August
Explanation

@nneettwwrrookkiinnggg

QUESTION 690 – Based on this thread it shoud be D “learningnetwork.cisco.com/thread/117389” . Another reason is, I think this is the same question as Q.416, just the phrasing is different.

QUESTION 416
Which action can you take to mitigate unicast flooding in a network?
A. Configure VLANs to span multiple access-layer switches.
B. Implement a nonlooped network topology.
C. Set the ARP timer value to less than the CAM timer value.
D. Set the CAM timer value to less than the ARP timer value.
Correct Answer: C

QUESTION 743 – Answer is correct, don’t mind me about this question. hehe

QUESTION 693 – Answer should be FF08:/16 as per this link “tools.ietf.org/html/rfc4291#section-2.7”

Fin go away. We dont need you. You are fake and your scam is exposed.

Fin go away. We dont need you. You are fake and your scam is exposed.

Anyone here taking the exam in the Philippines?

@Mosh

Me, Planning to take the exam within the week or early next week.

@ShutNoShut
keep in touch
you know my mail

hi guys, today i have passed 300-101 with 9xx. Thanks to you guys for contribution and finding the right answers. Special thanks to nneettwwrrookkiinnggg who shares the dumps which is super valid.

all Qs came from August 195 sections. for DnD, i got ACL, Frame-Relay LMI, GRE features, uRPF mode. for Sim, I got EIGRP OSPF redistribution, OSPF Sim, EIGRP Stub Sim but not Simlets.

But there are few wrong Qs in August 195 section though. all previous pages has the correct answers shared by @Hagar @JaJa and @Ahmet, and many more. So go thru all those Qs that they have discussed and you will be fine.

Thanks a lot guys! see you on TSHOOT :)

Hi,
Can anybody please share the links for LAB question and Solutions?

@madking
congratulations bro :) I am happy to hear
please contact with me

nneettwwoorrkkiinngg @ gmail.com

@abdulrahmansh
and all

abdulrahmansh says correct answers “D”
some people says A and C
What do you think?

QUESTION 737
Refer in the exhibit. A packet capture indicates that the router is not forwarding the DHCP packets that it
receives on interface FastEthernet0/0. Which command needs to be entered in global configuration mode
to resolve this issue?
A. ip helper-address
B. ip DHCP relay
C. service DHCP
D. ip forward-protocol
Correct Answer: A

ip helper-address is configured on int mode , so either the q is wrong or the ans is wrong, and the correct ans is D

https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipapp/command/iap-cr-book/iap-i1.html#wp1776761080

@nneettwwrrookkiinnggg

Hello questions 675 and 621 are similar, but answers are not !

QUESTION 675
A network engineer is enabling RIPng on a new customer link Under which configuration mode is RIPng enabled?
A. Global
B. Router
C. Interface
D. IPv6
Correct Answer: A (should be C)

QUESTION 621
Where do you enable RIPng?
A. Interface config
B. Something config
C. Global config
D. Router config
E. Something else config
Correct Answer: A

Hi guys, I am looking for routing dumps. please if someone could help me in this regard. please send me at
virtualnido at yahoo dot com

Hi Guys,
Will exam tomorrow, any advise?
Thanks

@ELO
QUESTION 675 and QUESTION 621 not same Questions

1(config)#ipv6 router rip RIPNGTEST <—A. Global
R1(config-rtr)#exit
R1(config)#interface fastEthernet 0/0
R1(config-if)#ipv6 rip RIPNGTEST enable <—C. Interface
R1(config-if)#exit
R1(config)#interface loopback 0
R1(config-if)#ipv6 rip RIPNGTEST enable

https: // networklessons.com/ipv6/how-to-configure-ripng-on-cisco-ios-router/

QUESTION 675
A network engineer is enabling RIPng on a new customer link Under which configuration mode is RIPng enabled?
A. Global
B. Router
C. Interface
D. IPv6

@hype_cisco

please contact with me
nneettwwoorrkkiinngg @ gmail.com

hello everybody , Please share me latest dumps for CCNP ROUTE 300-101.

@John Smith
please read some this forum :)

f.y.i.

drive.google.com/drive/folders/1Cf4MHTm8Qt5-_jYzJt6PXNy6b6YOBEx1

I passed my exam on the first attempt. with Braindumpscerts.com ROUTE 300-101 Dumps PDF was very user-friendly including all points of the exam course. It helped me out in an actual understanding. I got 90% score in the exam. I would like to say thanks to Braindumpscerts.com team for the suitable and decent support.

@nneettwwrrookkiinngg
Hi, sent you an email

Can anyone advise me to take premium membership of digitaltut is useful ?

@Anonymous
Ok bro
I will help you

@Networking
Hi all this user fake
please careful

go to hell fake users

we are not a rich, we need a job
go to hell

I just help people

@nneettwwrrookkiinngg

Hi,
I have dropped you an email.
Thanks :)

@nneettwwrrookkiinngg

Hi,
I have dropped you an email.Thank you for all the dumps you have provided so far,

Best Regards,
Andrew

@nneettwwrrookkiinngg

is there is necessary to real dumps of all section ? or Aug/Sep sections is enough to go through

QUESTION 373
Which two statements about NetFlow templates are true? (Choose two)
A. Only NetFlow version 9 is template based.
B. NetFlow Version 5 and version 9 are template based.
C. Only NetFlow version 5 is template based.
D. Template can increased bandwidth usage
E. They can increase overall performance.
F. They can reduce bandwidth usage.
Correct Answer: AD

Not sure about D, anyone else has a different answer, definitely A but could be D,E or F.

provide proof. thanks

@acme
how are you bro :)

correct answer are A,D

http://www.cisco.com/en/US/technologies/tk648/tk362/technologies_white_paper09186a00800a3db9.html

https: // vceguide.com/which-two-statements-about-netflow-templates-are-true/

Hi nneettwwrookiing my friend

yes I went over the link but I didn’t see anything about bandwidth or perfomance, it only shows proof for A answer. not sure about D

thanks

QUESTION 552
which condition prevents the establishment of a DMPVN tunnel between two spokes ?
A. HSRP is enabled on the spoke devices
B. IPsec is enabled on the spoke devices
C. the two spokes are behind different PAT devices
D. the two spokes have different tunnel keepalive settings.

answer should be C.

https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/sec_conn_dmvpn/configuration/xe-16/sec-conn-dmvpn-xe-16-book/sec-conn-dmvpn-dt-spokes-b-nat.html

“If one spoke is behind one NAT device and another different spoke is behind another NAT device, and Peer Address Translation (PAT) is the type of NAT used on both NAT devices, then a session initiated between the two spokes cannot be established.”

@acme
I agree with you
you are good :)
I will fix the answer

updated vce file

Guys, has anyone recently taken the test and passed using @nneettwrrookinggg’s material.

@nneettwrrookinggg, please share updated file.

I am plannng to take test in the next two weeks.

Thanks