Share your ENCOR v1.1 Experience

Fail the exam today.

the labs are the same @Hmizo June 10th, 2025

please practice the labs in simulator, if you just do it in a book you are going to have problem in the exam.

about 10 New Question.

if you want to use the TAB is work but not properly , in the examen you have to use almost the complete commando. example nei dont work but neighbor works.

Pass the exam today!
I got OSPF , BGP, VRF, LACP & Root Bridege, NetFlow and Copp Sims
Better to learn via EVE-NG and practiced.
Only study V1.1 part 1-7 questions, all questions are there apart from 5-8
Study drag and drop questions from the V1.1 part 1-7 questions.
Thank You Digitaltut!!!

Hi Paul

About the D&Drop, are they about automation (DEV, Json, phyton, etc) or the general knowledge?

What you have?

Thanks

Today I gave exam at Cisco Live center in San Diago, CA. Passed the exam. Got Labs – Switch Port Channel Issue, CoPP, OSPF Summarization, BGP Neighbor thru address family, VRF Config. ALso, experienced 10-12 new questions.

@Anonymous
What were the new questions about? Were they easy enough to answer?

@Soon
Yeah mostly about (DEV, Json, phyton, Ansible, etc)
Good thing is all are in here (V1.1 part 1-7 questions)

Congrats and thanks Paul

Any advice how i can practice the labs as I tried download EVE but unable to get it works my exam within 2 weeks ,Thanks

Hello HMIZO,

Congratulations on passing the ENCOR exam. Do you mind sharing the dumps you used to prepare for the exam on abdulhafizmatti2001atgmaildotcom thanks.

Hello Paul1010,
Congratulations on passing the exam. Do you mind sharing V1.1 part 1-7 questions with me on
abdulhafizmatti2001atgmaildotcom or direct me to where I can get it thanks.

Ok just passed exam today.

There were around 10 new questions mostly to do with wifi.
Labs were eBGP sim 2, VRF Configuration Sim 2 but didn’t have a configured VRF all config was done on router 11, OSPF summarization 2 however network statements were done in the router ospf process and not on the interfaces. Also range command was a /20 not /18.
Netflow sim 2 using IP SLA http get.
ACL & Copp however ACL had to permit OSPF than EIGRP and CoPP ACL has to permit telnet.
LACP & Root bridge for vlan 10 only

Hello guys :). I’m used this website to earn my ccna . Now I want to get the encor. I see everyone says “V1.1 part 1-7 and 5-8 questions” this question are available once again I pay the membership?

Passed the Exam, Thanks Guys.
The Labs are the same as everyone is getting and possibly 5-10 new questions.
Practice well on the LABS !!!

Could anyone get the “Control-Plane” plane command to work on the Access-list and COPP Lab on the Test? Or, do we have to put it on an interface on the test. Because, I could not get the global command Config# Control-plane to work.

Passed, Labs are same 6 with minor changes which can be handled with practice, 5-8 new Questions.

Passed the exam today.
– There were around 5-6 new questions Wifi/Python.
– All the remaining questions from ENCOR v1.1 Questions – Part 1-7.
– Practice Lab Sims, I got the below in the exam:
– eBGP sim 2
– VRF Configuration Sim 2, VRF FINANCE was already created, Configure only on router 11
– OSPF summarization 2, configure interfaces not the network command. Range command /18.
– Netflow sim 2 using IP SLA http get.
– ACL & COPP , ACL had to permit EIGRP and CoPP ACL has to permit SSH.
– LACP & Root bridge for vlan 10 only
I was surprised that the copy and paste (right click doesn’t work) option was not there, lab Sims took more time than expected.
Thanks Digitaltut :D
Good Luck Everyone!

Pass the Exam!!
I got 60 questions in total (6 LabSims + 50 Multiple Choises Questions + 4 Drag & Drop).
All questions were from here. Except 3 to 5 questions.

LabSims (6, all from here):
1. eBGP sim 2: with Address Family
2. VRF configuration sim 2: the VRF Finance was already configure
3. OSPF summarization sim 2: OSPF without using the network command. Summarize with /16.
4. Netflow sim 2: Including IP SLA using ICMP-ECHO that ping Switch’s Loopback0 Interface every 300 secondes
5. ACL & COPP: ACL had to permit EIGRP and CoPP ACL has to permit icmp for a Host (not subnet).
6. LACP & Root: Bridge for vlan 10 and 30. Port-Channel 12 was already configure with access vlan 10. Also the Interface were configure with access vlan 10.

During the Exam TAB and “?” are working. But Copy & paste not.

I spended in total 3 months for preparation:
1x Month ready the officiel book from Cisco press(CCNP and CCIE Enterprise Core ENCOR 350-401 Official Cert Guide). Pdf doanwloaded for free from the Internet
2x Months on this Website (Premium Member Zone). Reviewed all ENCOR v1.1 Questions – Part 1 to Part 7. plus ENCOR Questions – Part 4 to ENCOR Questions – Part 11. Plus Lab Sims for ENCOR v1.1.

I installed EVE-NG on Google Gloud to build the Lab and practise the sims.

Thank you digitaltut for all the Stuff in place.

I passed exam, already 3-5 question news for WIFI and SD- ACCESS

All la this here, I have 5 lab:
Tunnel-vrf CoP
Netfow sim 1
OSPF summary /20
Trunk – LACP – root
ACL OSPF and traffic shaping

And 54 question

Hi Dylan R,

You mentioned that all the labs are here — may I know where exactly? Are they under LAB Challenges or under Basic Labs?

Thanks.

@Leo you can see the labs if you have the premium subscription.

Passed today, everything here is valid.

study and practive lab simulations.
questions v1.1 1-7 more than enough to answer non lab related questions.

which lab you did?

any one passed the test these days. … please do share your experience. thank you

Wrote the exam today and passed.

54 multiple choice questions and 6 labs. All from here.
VRF Configuration Sim
Netflow Sim
eBGP Sim 2
OSPF Summarisation Sim 2
Access list and CoPP
Trunk UDLD & LACP Sim

did the ff labs:

NetFlow Sim 2
OSPF Advertised & Summarized Sim
Access-list & CoPP Sim
VRF Configuration Sim
eBGP Neighbor Sim 2
LACP & Root Bridge Sim

Did you get question from ENCOR v1.1 part1 – part 7?

Hey all, thanks for your help with this.
I have managed to pass recently

there are 2 questions that i have noticed:
one about dbms with value on locations like 72,65,75,8.. and how you would explain the values in each location to the customer
And another about controller json output and what would that show i do not remember this one.
All the rest is fine and the labs are as above

Hi,

I pass the exam. I think I saw two new questions, but all the other questions were here. It starts with six practical exercises, and then the questions come in. The practical exercises are basically the same; only the IP addresses, AS numbers, etc., change. Thank you very much. I only studied from this page.

Hi… I’m really sorry to bother,
But I just want to ask…
If I study only ENCOR v1.1 Questions – Part 1-7, will it be enough to pass the exam?
Please… If anyone has passed, I really really need your help…
I don’t have much time or money left, and I’m trying my best…
Any advice or confirmation means the world to me.
Thank you so much in advance. 🙏🥺

I have passed my 350-401 today. Thanks to Dumpsforsure.

Hi

I have passed my 350-401

6 Labs and 54 Questions

Study New ENCOR v1.1 Part 1-7

thank you

@Mark thank you for review 🙏🙏

@Mark… what labs you had.. and new questions

Hi

I passed the exam on Saturday.
All Labs are from here and most of the questions apart from about 10 new questions.

Thanks

ENCOR v1.1 Part 1-7… how many questions are there?

@Anonymous you write CCNP everyday july 13th u wrote CCNP ,July 16 u write CCNP

Exam done and passed , after 6 long moths of studying…
Cisco Press (for the first time, is a waste of time) + DigitalTut…
DigitalTut I read and study every chapter, every question, everything so if you are looking to tell you about Dump questions I’m not the right person …
About the exam, I study all questions, old, the questions from chapters and the last ones and I could say that ALL of my questions was here. Maybe 2 or 3 was written a little bit different but at the end was easy to answer them…
LABS was almost identical, just change IP’s/areas etc…
D&D, for my surprise I had almost 10 (!!!) all of them from here too
From 1.1 part 7 I had 3/4 questions and all the other I can not tell if was from 1.1, 1.0 of chapter questions because I study all of them…
My exam was “balanced” in terms of topics, I had a bit of everything except Routing… I did NOT had any routing questions (only the labs are about routing protocols)…
If you study well then the exam is easy…

Thanks DigitalTut, one more time, tremendous site, community and study content !!! keep the good work!!!
good luck everyone

Congrats to you guys for passing the ENCOR. anyone planning to take CCIE lab exam in near future? im looking for study group, would be great if digitaltut also provides learning material like it was for old v5, nowadays there’s not much active place to study CCIE exam.

Passed the exam today

6 labs, 54 questions.

VRF configuration through the tunnel. VRF was already present. No VRF routing, just build the tunnel from scratch
LACP & Root bridge
eBGP neighbor sim 2
ACL & COPP
OSPF Summarization with interface configuration and no network statement (ip ospf 1 area 0…)
Netflow Sim. Exporter to be completed with transport udp 2055. It wasn’t asked to configure the interface with the ip flow traffic, I did it in case…

AS & IPs might change obviously, just read carrefully.

I spotted 2 new questions. others were part of v1.1 part1-7

good luck everyone

Passed the exam today

6 labs, 60 questions (All from v1.1 parts 1-7)

VRF Configuration Sim 2
LACP & Root bridge
eBGP neighbor sim 2
ACL & COPP
OSPF Advertised & Summarized Sim
NetFlow Sim 2

Be carefull about the tasks and the ip address configuration of the hosts

2 or 3 new questions about wifi 5ghz, rssi and JSON.

Thanks @digitaltut. Everything you need is here.

@ Robil l want to ask u got Netflow Sim not Netflow Sim 2 ?

I passed the exam today

I got 60 questions in total – 6 labs and 54 questions

VRF Configuration Sim 2
LACP & Root Bridge
eBGP Neighbor Sim 2
OSPF Summarization Sim 2 – summarized /16 range
ACL & CoPP – permit host for telnet traffic
NetFlow Sim 2

Of course, the ip addresses, AS (for BGP) and the devices to configure will change

There were about 2-3 new questions.

I studied all the questions here and practiced the composite quiz multiple times, so I can’t tell where exactly the questions came from.

After studying for 6 months, this was a great platform to tie everything together. Thank you so much @digitaltut for being so reliable.

Wishing everyone else planning to take the exam soon great success.

Hi all, someone having premium membership please give insite for total number of questions need to remember for passing exam. I am planning to pass it and need to manage my work and preparation time accordingly. total questions or less the 500 or more

Hi, @CCNP EI renewal
Based on recent updates from premium users, there are around 600 new questions added, plus approximately 600 older ones, making it about 1,200 questions total.

It’s not 100% confirmed whether focusing only on new ones is enough to pass, but many suggest reviewing both new and most recent repeats for a safer bet. Good luck!

@Pass exam. Few new questions (6-7) and new dag and drop questions and new question with new scheme.. I have studied all questions from this Filee and i have read sdwan guide. In drag and drop here answers but in exam 3 (traditional firewall/application aware),.

Creatt / betwiin z4
zzb.bz4bsQe

Thanks to Dumpsforsure. I have passed my 350-401 exam.

@stephen.. can you please do let me know what labs you had.. and questions you know about… as my exam is soon… thank you

Passed 350-401

6 labs 54 Questions

I took 8weeks on this site.

Studied 1.1 Part 1-7 and part 1.0 Part 10-11 only

This is enough to pass the exam as most of the questions came from 1.1

On the labs
LACP
ACL COPP
EBGP 2
NETFLOW 2
VRF 2
OSPF summarization

do the labs to understand the concepts well

Best of luck

@Paas_CCNP… can you please do elaborate more on labs… also… what you mean with and part 1.0 Part 10-11 only…. it is only Part 10-11 and not all part 4 to part 11 …. Thank you

l had a limited time to take my exam , hence l only studied v1.1 and part of 1.0 (Part 10-11)

if you have enough time take v1.0 part 4-11 ( about 500+ questions

v1.1 is enough to make you pass the exam (this is also about 500+ questions

total of about 1000+ question

on labs
ip addresses can be different , AS number