Share your ROUTE v2.0 Experience

@Mosh

what are the two correct statements about enable secret and enable password command
A.the enable password command has a strong encryption algorithm than enable secret
B.if both commands are missing from the global configuration, vty lines use the console password
C.the enable secret command is backwards compatible with more versions of IOS
D.the enable secret and enable password commands must be used together
E.the enable secret command overrides enable password

Correct Answer: BE

Cisco IOS command reference:
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/security/d1/sec-d1-cr-book/sec-cr-e1.html#wp3438133060

“If neither the enable password command or the enable secret command is configured, and if a line password is configured for the console, the console line password will serve as the enable password for all vty (Telnet and Secure Shell [SSH]) sessions. ”

Also:
“After you set a password using the enable secret command, a password set using the enable password command works only if the enable secret is disabled or an older version of Cisco IOS software is being used, such as when running an older rxboot image.” – this means that not all of the IOS versions supports “enable secret” command so it is not backward compatible.

Hi AMAN, from the URL, see below info. I still highly think “B” is the correct answer.

Configuring Multiple NetFlow Export Destinations to a Router
To configure multiple NetFlow export destinations to a router, use the following commands in global configuration mode:

Command
Purpose
Step 1

Router(config)# ip flow-export destination ip-address
udp-port
Enables the exporting of information in NetFlow cache entries.

Step 2

Router(config)# ip flow-export destination ip-address
udp-port
Adds a second export destination.

Note Do not enter the same ip address twice. However, entering two different ip addresses with the same udp port number is configurable.

QUESTION 655
Which adverse event can occur as a consequence of asymmetric routing on the network?
A. vulnerability to a man-in the – middle atack
B. inadventent HSRP active router preemption
C. errdisabled port
D. unicast flooding
Correct Answer: D!!

Reference:
https://www.cisco.com/c/en/us/support/docs/switches/catalyst-6000-series-switches/23563-143.html

Thanks @Anonymous01 . Our answers are the same, the choices are just jumbled..

QUESTION 679
Which two features were added in MSCHAP version 2?(Choose two)
A. Mutual authentication between peers.
B. Using the MD5 hash for stronger security
C. Using three-way handshakes for authentication.
D. Ability to change an expired password
E. Backward-compatibility with MSCHAP version 1
Correct Answer: AD!!

Reference:
“The MSCHAP Version 2 feature in Cisco IOS Release 12.2(13)T introduces the ability of Cisco routers to utilize Microsoft Challenge Handshake Authentication Protocol Version 2 (MSCHAP V2) authentication for PPP connections between a computer using a Microsoft Windows operating system and a network access server (NAS). MSCHAP V2 authentication is an updated version of MSCHAP that is similar to but incompatible with MSCHAP Version 1 (V1). MSCHAP V2 introduces mutual authentication between peers and a change password feature. ”

https://www.cisco.com/c/en/us/td/docs/ios/12_2sb/12_2sba/feature/guide/sbaschap.html

QUESTION 389
Refer to the Exhibit.
configure terminal
ip flow-export destination 192.168.10.1 9991
ip flow-export version 9
How can you configure a second export destination for IP address 192.168.10.1?
A. Specify a different TCP Port
B. Specify a different UDP port.
C. Specify a VRF
D. Configure a version 5 flow-export to the same destination
E. Specify a different flow ID

Kikavich and nneettwwoorrkkiinngg say the answer is “C” but I think think the answer is “B”.
What do you guys think?

Most recent person who passed posted Aug 12th

“So i wrote my exams a couple of days ago and passed thanks to this site. I am now re-certified. I used the nneettwworrkking dumps (v1.0) and i was also a premium member. I had a total of 53q. I had 3 Labs: EIGRP stub, EIGRP OSPF Redistribution(case 2) and IPV6 OSPF Virtual link. I did not get any of the simlets in my exam.

Just came back here to share and i saw a link @nneettwworrkkkinng posted for the version 2.0 with new questions and i decided to download and check it out and i call TELL you that some of the questions in the August tab were in my exams, i promise you that. I don’t know how they got the questions but i could pick some from that section.

Thanks a lot @nettwwoorrkkkinng for taking out the time to put the dumps together and for all those who contributed. Now that i am done with my exam, i can relax. Best of luck to you all”

Also looking for anyone who has passed recently, I ha

QUESTION 389.
Refer to the Exhibit.
configure terminal
ip flow-export destination 192.168.10.1 9991
ip flow-export version 9
How can you configure a second export destination for IP address 192.168.10.1?
A. Specify a different TCP Port
B. Specify a different UDP port..
C. Specify a VRF
D. Configure a version 5 flow-export to the same destination
E. Specify a different flow ID

Kikavich and nneettwwoorrkkiinngg say the answer is “C” but I think think the answer is “B”.
What do you guys think?

QUESTION 384
Which OSPF area prevent LSA type 4, LSA type 5? (Choose Two)
A. Stub Area
B. Totally Stubby Area
C. Not-So-Stubby Area
D. Totally Not-So-Stubby Area
Correct Answer: BD >>>>>>>> I think all options are correct!!! >> All Stub and NSSA area types prevent LSAs 4 and 5.

What you guys think ?

Nevermind guys !! I got the explanation right next the Q384.

@MOSH

A, B are right.
D is not only wrong described, we could discuss it, but definitely enable sercret is relativ “new”, so it doesn´t really fit in the answer. I find A more right ;)

Today I passed, 94x/100
So many Thank @nneettwwrrookkiinnggg, hard_working.
I studied your dump v2, I don’t see any new questions. Dear all, please study this dumps.
Laps:
1: EIGRP OSPF Redistribution Sim
2: IPv6 OSPF Virtual Link Sim
3: EIGRP Stub Sim

@nneettwwrrookkiinnggg, your dump file is valid,
but all of your answer is not correct. please correct
for other person, but thanks any wary.
May god bless you.

just passed the exam got 9xx..

Thank you @nneettwwoorrkkiinngg!!!

all the questions were from his file, drag and drop and MCQ.
Digitaltut lab is valid too..

There were questions that I had given my own answer (used my correction on my previous post as my answers)

Those are the Wrong questions I have found in the newest @nneettwwoorrkiingg Dumps:
___________
Q167

network engineer applies the command ip tcp adjust-mss under interface configuration mode. What is the result?
A. The probability of SYN packet truncation is increased.
B. The UDP session is inversely affected.
C. The probability of dropped or segmented TCP packets is decreased.
D. the optimum MTU value for the interface is set.

In VCE: D
Correct ANS: C
___________
Q641

Which lsa type does propagate into area 1 for the 192.168.10.0/24 network?
(Area 1 is a NSSA)

A. Type 3
B. Type 5
C. Type 7
D. Type 10

In VCE: B
Correct Ans: C
___________
Q189

A network engineer executes the show ip cache flow command. Wich two types of information are displayed in the report that is generated? (Choose two)

A. Top talkers
B. Flow export statistics
C. Flow sample for specific protocols
D. MLS flow traffic
E. IP packet distribution

In VCE: B, C
Correct Ans: C, D
___________
Q229

Which SNMP verification command shows the encryption and authentication protocols that are used in SNMPV3?

A. show snmp view
B. show snmp
C. show snmp user
D. show snmp group

In VCE: D
Correct Ans: C

___________
Q647 D&D about Frame Relay – Doesn´t make any sense at all.
___________
Q662 – Which adverse circumstance can TTL prevent?

A. Routing loops
B. DoS attacks
C. link Saturation
D. CAM table overload

In VCE: D
Correct Answer: A
___________
Q621 – Which two causes of latency are true?

A. High Bandwith on a link
B. Split horizon
C. Propagation Delay
D. Serialization Delay
E. Under-utilization of the link

VCE Answer: C, E
Correct Answer: C, D
___________
Q535 – Which task must you perform to enable a point-to-point frame relay connection?

A. Configure the encapsuation type
B. Disable inverse ARP
C. Enable inverse ARP
D. Configure static address mapping

VCE Answer: D
Correct Answer: A
___________
Q537

In which two areas doe OSPF send summary routes by default

A. NSSA
B. Backbone
C. Totally Stubby
D. Stub
E. Normal

VCE Answer: D, E
Correct Answer: C, D
___________
Q700

Company is deploying a multicast application that must be accesible between sites, but must not be accesible outside of the organization based on

A. FF00:/16
B. FF0E:/16
C. FF02:/16
D. FF08:/16

VCE Answer: C
Correct Answer: D

Which two statements about Frame Relay Point-to-Point connections are true? (Choose Two)
___________
Q366

A. Changing a point-to-point subinterface to a different type requires the device to be reloaded.
B. They use two DLCIs to communicate with multiple endpoints over the Frame Relay cloud. C.The device can establish a point-to-point connection to the cloud without a DLCI.
D. They can operate normally without a DLCI map.
E. Each physical interface that extends to the Frame Relay cloud can support a single SVC.

VCE Answer: A, B
Correct Answer: D, E
___________
Q404

Which technology is required on an EVN trunk interface?
A. 802.1q
B. NAT
C. VRF-Lite
D. IS-IS

VCE Answer: C
Correct Answer: A

@Zaw Eikmyat

if u r myanmar please call 09975497712 let me ask some

Just past today (8/15) with a 911. Big thanks to @nneettwwoorrkkiinngg!! Very much valid.

SIMS– Eigrp Stub / Redist / OSPF (Area numbers changed)

D and D — FR LMI extensions / GRE features / loose-strict mode / ACL types.

2 down 1 to go….on to tshoot!

Everybody,
focus on August 141q.

Kfed

For SIMS was it OSPF Evaluation Sim?

@delwans

QUESTION 366
Which two statements about Frame Relay Point-to-Point connections are true? (Choose Two)
A. Changing a point-to-point sub interface to a different type requires the device to be reloaded.
B. They use two DLCls to communicate with multiple endpoints over the Frame Relay cloud.
C. The device can establish a point-to-point connection to the cloud without a DLCI.
D. They can operate normally without a DLCI map.
E. Each physical interface that extends to the Frame Relay cloud can support a single SVC.
Correct Answer: AB

AB is correct answers other all question you choose the answers are right networkkkking only change the answers behalf of ANN and now ANN is disappear lol .

@Asd_me Cong Brother help to all folks belong to preparing exams for Routing in the below list which question you received and what was your answers please your feedback :)

Those are the Wrong questions I have found in the newest @nneettwwoorrkiingg Dumps:
___________
Q167

network engineer applies the command ip tcp adjust-mss under interface configuration mode. What is the result?
A. The probability of SYN packet truncation is increased.
B. The UDP session is inversely affected.
C. The probability of dropped or segmented TCP packets is decreased.
D. the optimum MTU value for the interface is set.

In VCE: D
Correct ANS: C
___________
Q641

Which lsa type does propagate into area 1 for the 192.168.10.0/24 network?
(Area 1 is a NSSA)

A. Type 3
B. Type 5
C. Type 7
D. Type 10

In VCE: B
Correct Ans: C
___________
Q189

A network engineer executes the show ip cache flow command. Wich two types of information are displayed in the report that is generated? (Choose two)

A. Top talkers
B. Flow export statistics
C. Flow sample for specific protocols
D. MLS flow traffic
E. IP packet distribution

In VCE: B, C
Correct Ans: C, D
___________
Q229

Which SNMP verification command shows the encryption and authentication protocols that are used in SNMPV3?

A. show snmp view
B. show snmp
C. show snmp user
D. show snmp group

In VCE: D
Correct Ans: C

___________
Q647 D&D about Frame Relay – Doesn´t make any sense at all.
___________
Q662 – Which adverse circumstance can TTL prevent?

A. Routing loops
B. DoS attacks
C. link Saturation
D. CAM table overload

In VCE: D
Correct Answer: A
___________
Q621 – Which two causes of latency are true?

A. High Bandwith on a link
B. Split horizon
C. Propagation Delay
D. Serialization Delay
E. Under-utilization of the link

VCE Answer: C, E
Correct Answer: C, D
___________
Q535 – Which task must you perform to enable a point-to-point frame relay connection?

A. Configure the encapsuation type
B. Disable inverse ARP
C. Enable inverse ARP
D. Configure static address mapping

VCE Answer: D
Correct Answer: A
___________
Q537

In which two areas doe OSPF send summary routes by default

A. NSSA
B. Backbone
C. Totally Stubby
D. Stub
E. Normal

VCE Answer: D, E
Correct Answer: C, D
___________
Q700

Company is deploying a multicast application that must be accesible between sites, but must not be accesible outside of the organization based on

A. FF00:/16
B. FF0E:/16
C. FF02:/16
D. FF08:/16

VCE Answer: C
Correct Answer: D

Which two statements about Frame Relay Point-to-Point connections are true? (Choose Two)
___________
Q366

A. Changing a point-to-point subinterface to a different type requires the device to be reloaded.
B. They use two DLCIs to communicate with multiple endpoints over the Frame Relay cloud. C.The device can establish a point-to-point connection to the cloud without a DLCI.
D. They can operate normally without a DLCI map.
E. Each physical interface that extends to the Frame Relay cloud can support a single SVC.

VCE Answer: A, B
Correct Answer: D, E
___________
Q404

Which technology is required on an EVN trunk interface?
A. 802.1q
B. NAT
C. VRF-Lite
D. IS-IS

VCE Answer: C
Correct Answer: A

@NewGuy it was the osfp sim with the 3 cities. (They also changed the cities names to like indy , settle, and alt)

I did NOT get any of the two simlets (eigrp / ospf)

Hi,
Could anyone please confirm which dumps are valid/correct answers. nneettwwpprrkkiinngg V.2 or v.1.2 634Questions.

Thank you in advance.

@kfed do you remember the MCQs?

May you write some of them

@Ahmed

Q537

In which two areas doe OSPF send summary routes by default

A. NSSA
B. Backbone
C. Totally Stubby
D. Stub
E. Normal

Totally stubby area
A totally stubby area is similar to a stub area. However, this area does not allow summary routes in addition to not having external routes, that is, inter-area (IA) routes are not summarized into totally stubby areas. The only way for traffic to get routed outside the area is a default route which is the only Type-3 LSA advertised into the area. When there is only one route out of the area, fewer routing decisions have to be made by the route processor, which lowers system resource utilization.

sorry, I mixed one answer!

___________
Q189

A network engineer executes the show ip cache flow command. Wich two types of information are displayed in the report that is generated? (Choose two)

A. Top talkers
B. Flow export statistics
C. Flow sample for specific protocols
D. MLS flow traffic
E. IP packet distribution

Right Answer: B, C!!

@Ahmed

Q167
C

Q641
wasn’t asked on my exam

Q189
C,E

Q229
D

Q662
A

Q621
wasn’t asked on my exam
but I would answer
C, D

Q535
wasn’t asked on my exam

Q537
C, D

Q700
D

Q366
D, E

Q404
A

I am not sure if I am right or wrong, all I can say is I did pretty well at 9xx score

@nneettwwoorrkkiinngg!!

please update vce with the correct answer.
thanks.

hello everybody,
if you know the correct answer, please confirm answer!

QUESTION 651
Which two statements about EVN are true?
A. It supports IPv6 traffic.
B. It can support up to 16 VNs.
C. It uses redistribution to share routes between VNs.
D. It supports SSM only.
E. A configuration can be based on an existing VRF configuration
Correct Answer: CE. my answer > A, E. ???

@ asd_me
please contact me;
veryyhardworking @ gmail.com

@ZEM do you want share maybe the 141 questions.

Hi all
I am working about wrong answers
Don’t worry
I will update the files

@kfed
Congrats bro
:)

@Asd_me

Thanks for sharing your experience with us and cong again bro .

i think your answers were correct that’s why you get score above 9** .

Networkkkkkkking please update the correct answers we don’t want anyone lost his time and money as well .

@nneettwwoorrkkiinngg thank you so much for your help.

hi guyz wana do my exam on 8/21 am wonder wea i cn get the @nneettwwoorrkkiinngg plz gv me a feel back thxxx

@Ahmed

DLCI Map you need it for Frame Relay Point-to-Multipoint connections, that´s why D is correct ;)

QUESTION 366
Which two statements about Frame Relay Point-to-Point connections are true? (Choose Two)
A. Changing a point-to-point sub interface to a different type requires the device to be reloaded.
B. They use two DLCls to communicate with multiple endpoints over the Frame Relay cloud.
C. The device can establish a point-to-point connection to the cloud without a DLCI.
D. They can operate normally without a DLCI map.
E. Each physical interface that extends to the Frame Relay cloud can support a single SVC.

NEEETWORKING_V2

QUESTION 189
A network engineer executes the show ip cache flow command. Wich two types of information are displayed in the report that is generated? (Choose Two)
A. top talkers
B. flow export statistics
C. flow sample for specific protocols
D. MLS flow traffic
E. IP packet distribution

I think it’s C, E … digitaltut justifies it well, I guess. LOL. PLEASE CONFIRM

Q189

A network engineer executes the show ip cache flow command. Wich two types of information are displayed in the report that is generated? (Choose two)

A. Top talkers
B. Flow export statistics
C. Flow sample for specific protocols
D. MLS flow traffic
E. IP packet distribution

should be C and E

sample
pppow_cleint#show ip cache flow
IP packet size distribution (0 total packets):
1-32 64 96 128 160 192 224 256 288 320 352 384 416 448 480
.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000

512 544 576 1024 1536 2048 2560 3072 3584 4096 4608
.000 .000 .000 .000 .000 .000 .000 .000 .000 .000 .000

IP Flow Switching Cache, 0 bytes
0 active, 0 inactive, 0 added
0 ager polls, 0 flow alloc failures
Active flows timeout in 30 minutes
Inactive flows timeout in 15 seconds
last clearing of statistics never
Protocol Total Flows Packets Bytes Packets Active(Sec) Idle(Sec)
——– Flows /Sec /Flow /Pkt /Sec /Flow /Flow

SrcIf SrcIPaddress DstIf DstIPaddress Pr SrcP DstP Pkts

Just checked and Q189 seems to be as you guys say… I will discuss it with my teycher tomorrow again.
Sorry :)))

QUESTION 522
How can you mitigate fragmentation issues between endpoints separated by a GRE tunnel? (they changed it, they added GRE)
A. PMTUD
B. TCP MSS
C. windowing
D. ICMP DF bit (this was a new answer)
Correct Answer: A??
please confir A o B???

QUESTION 540
Which three methods can a network engineer use to fix a metric based routing loop in the network.
A. A.Implement offset lists at network boundaries
B. B. Filter routes manually using distribute lists
C. C. Filter routes manually using prefix lists
D. D. Implement proper network summarisation on key routing points
E. E. Filter routes based on tags
F. F. Utilise root database filters
Correct Answer: ABE
ABE o BCE ??????? Please confirm

@nneettwwoorrkkiinngg, why should we have to wait days to get a corrected file, when you can just provide the password to said file and ANYONE can update it?

-seems pretty logical

@nneettwwoorrkkiinngg, I understand you’re taking your own personal time to do this, but seems quite easy to just provide the password so that others may update the file and share

@nneettwwoorrkkiinngg

please upload the new version with the correct answer.
thanks.

@nneettwwoorrkkiinngg

VCE file showing only one selection, but question is asking for 3 answer. Hoping you may share the updated file. thank you.

QUESTION 683
Which three algorithms can you configure with the ip cef load-sharing algorithm command?(Choose three)
A. per-packed
B. Tunnel
C. per-destination
D. UniversalE. Per-source
F. Include-ports

@ExamFriday
The information in this area is real and effective, and the update is fast. Those in need can go and see it.

QUESTION 540
Which three methods can a network engineer use to fix a metric based routing loop in the network.
A. A.Implement offset lists at network boundaries
B. B. Filter routes manually using distribute lists
C. C. Filter routes manually using prefix lists
D. D. Implement proper network summarisation on key routing points
E. E. Filter routes based on tags
F. F. Utilise root database filters

I think it’s BCE.. Already tried it to prevent routing loops.

can anyone share @nneettwwoorrkkiinngg version 2.0 August 141q here..i couldnt find the link.please post here.

its so good to find a site where people generally discuss about exam topics,questions and their opinions about the right answer.it cleared some doubts and guide me to study again on mentioned important chapters.thank you so much to all members for their efforts.

This link has the 1.1 and 2.0 versions. I suggest only studying the 1.1 version as the 2.0 version has many many wrong answers and @nneettwwoorrkkiinngg refuses to publish the password to the file so that we may update the wrong answers.

https://drive.google.com/open?id=1Sy6ex-6XijzMp7RlZiW4buhMXVDDWCDe