Share your ROUTE v2.0 Experience

@Peter, check and study Lab Sim

@Mu, Great! Thanks!

@acme, thank you! So anxious on the exam. Will be taking it last week of october.

Hi all, I believe the @netwroking answer to this question is not correct:
Which two causes of latency are true? (Choose two)
A. High bandwidth on a link
B. Split horizon
C. Propagation delay
D. Serialization delay
E. Under-utilizaion of a link
@networking answer: CE what I guess is correct answer:CD see link below:

https://www.ccexpert.us/network-design-2/causes-of-delay.html

where is the nneettwwoorkkinnng Sep 195 dump everyone keeps talking about?

networking195q and digitaltut labs still valid? Who knows?
Exam tomorrow. Please inform us.

plz can you answer this Questions:

Which two statements about PAP and CHAP authentication are true? (Choose two)
A. PAP uses a challenge string from the server to the client.
B. PAP can query a TACACS+ server to verify access credentials.
C. CHAP requires the client to supply a username and optional password.
D. PAP requires the client to supply a username and optional password.
E. CHAP uses a challenge string from the server to the client.

Which two statements about IP access-lists are true? (Choose two)
A. IP access-lists without at least one deny statement permit all traffic by default.
B. Extended access-lists must include port numbers.
C. They support wildcard masks to limit the address bits to which entries are applies.
D. Entries are applied to traffic in the order in which they appear.
E. They end with an implicit permit.

Which two statements about ICMP unreachable messages are true?(Choose two
A. They are sent when a route to the destination is missing from the routing table
B. They can be enable and disable on a device only on a global level
C. They are sent when a destination address responds to an ARP request
D. They include the entire packet so that the source can identify the process that generated the message
E. They include a poriton of the original data so that the source can identify the process that generated the message

Which routing protocol routers traffic throught the best path and seccond best path at the same time?
A. EIGRP
B. BGP
C. OSPF
D. RIP

An administrator needs to setup an NTP client to provide updates to local without synchronizing to server. What is the command?
A. Serve
B. Serve-only
C. peer
D. query

Which command do you enter to filter only routing updates that are sent through interface GigabitEthernet0/0?
A. R1(config-if)# passive-interface GigabitEthernet0/0.
B. R1(config-router)# no passive-interface GigabitEthernet0/0
C. R1(config-router)# passive-interface GigabitEthernet0/0
D. R1(config-router)# passive-interface default
E. R1(config-if)# passive-interface default
F. R1(config-router)# distribute-list 1 out GigabitEthernet0/0

Can somebody please send the nnnettworking and SPOTO dumps that everyone keeps talking about to {email not allowed}

email : rsoma8869 @ gmail.com

Dear app Hi.

Please share with me valid dumps 300-101 route Ultel93 @ gmail.com
Thanks in advance

in D&D our answer should be in order or not necessary.

For example.
IN TACACS+ USE TCP is target 1 but I drag on Target 2 its showing incorrect answer in VC??

Is it necessary to have answer in same order.

any previous shared dumps in comments?let me know the page

@anonymous – i know these are correct. not sure about the other two.

Which two statements about IP access-lists are true? (Choose two)
C. They support wildcard masks to limit the address bits to which entries are applies.
D. Entries are applied to traffic in the order in which they appear.

Which routing protocol routers traffic throught the best path and seccond best path at the same time?
BGP

An administrator needs to setup an NTP client to provide updates to local without synchronizing to server. What is the command?
A. Serve

Which command do you enter to filter only routing updates that are sent through interface GigabitEthernet0/0?

C. R1(config-router)# passive-interface GigabitEthernet0/0

which labs are “digitaltut” labs? how can I download them?

IPV6 OSPF Virtual -Link lab

Configuration of R4 as its stated that to get full marks disable this command
area 54 virtual-link 3.3.3.3

if we disable this we cannot ping from R1
If we disable this command then There is interface loopback 0 we have to assign area 54

where are the questions in lab sim “EIGRP Evaluation Sim”? anyone knows?

Can someone guide me what are the labs need to be practiced? Exam this weekend.

Pls pls someone respond to me pls.
If by chance if you have links to the lab pls share.pls

Reflecting more about this I came to the conclusion that at the end of the day the CCNP certification is intended to be used as an asset for Cisco partners/vendors so they can get discounts when buying solutions. This discounts might be returned to Cisco in the form of exam attempts that the candidates that are already working with Cisco equipment take.

In my opinion, the candidates for this exam should not pay for it, but the company where they work should. In this way failure is not unfair. Cisco makes the candidate fail on purpose so it can get back some of the money that is already giving away on discounts. In addition, some of the CBTs that candidates can take already mention that consider the 1st attempt of the exam as a learning experience, and failure is very likely, not because of the difficulty per se, but because of the topics that will be asked and that either were not very clearly pointed out in the objective list, or indeed are totally out of scope. In the 1st attempt ideally the candidate should memorize the questions and topics he was asked and did not know the answer, so later he/she goes back to study them, and then retry doing the test.

Hi,

Cleared the exam on saturday in india. Got 850 by mistake lab got skipped. And My friend got 955 . Thanks @Nneettwwoorrkkkiing . 195 Q are valid. Labs same as digital tut. Got EIGRP ospf redirtibution, OSPFV6 virtual links. OSPF stub…DND also same only. Dumps are super valid. Few answers may be wrong.

@cosco, do you have the lab GNS files ? can you help providing them ??

HI.

I did not practiced any labs…Just read the commands directly attempted exam. No need of practice. Labs are from dgital tut only..

@ help required:

here under are the labs that you have to study to pass the exam

https://www.digitaltut.com/category/route-300-101/lab-sim

@Cosco @Mizo… thank you guys (y)

@ Nneettwwoorrkkkiing

QUESTION 709
which access list used to filter upper layer protocol ?
A. extended acl
B. standart acl
C. reflexive acl
D. time based acl
E. dynamic acl

it’s answered in the Networking dump in the MCQs : extended acl ; & in the DND: reflexive acl
can anyone advise which answer is the correct answer

Passing the ROUTE 300-101 exam is not an easy task, it requires Hard word & dedication plus Valid and up-to-date exam study material. I had a great experience of using braindumpscerts.com 300-101 exam PDF, by learning 300-101 exam questions I passed my 300-101 Exam with 88% score. I must recommend this to all who wants to pass the 300-101 Exam on the first attempt.

Today I passed with 9xx.
Lab: EIGRP stub, EIGRP OSPF redistribution, IPv6 OSPF virtual link.
DnD: CoPP and MPP, IPv6 traffic fitter and IPv6 Access Classes, AAA features, GRE features,
I just studied digitut and SPOTO 146q.
Some answers from VPN technologies, network principles and layer 2 technologies are wrong.
But I recommend to just study questions from digitut and SPOTO 146q.

@Mizo

QUESTION 709
which access list used to filter upper layer protocol ?
A. extended acl
B. standart acl
C. reflexive acl
D. time based acl
E. dynamic acl

it’s answered in the Networking dump in the MCQs : extended acl ; & in the DND: reflexive acl
can anyone advise which answer is the correct answer

the question as stated, extended acl fits best, with extended acl you can specify protocol and/or port numbers. I believe the DnD uses the key word “sessions” so reflexive would be a better fit, reflexive acl will automatically create an acl line to allow replies from an active communication sessions initiated from an “inside” device.

SPOTO 146q , where do i get these from

I passed today with 9xx.
The nneettwwrrookkiinnggg 195q completely valid.
Lab: eigrp stub, rigrp ospf redistribution, ospf.
Thanks @nneettwwrrookkiinnggg and @digitaltut

Please get SPOTO 146q
https://www.dropbox.com/sh/u1km51lw373o4l5/AABRA_gFlCLP6Qkov16_dJxma?dl=0

..
um..
can i hear?? what`s dnd ???

New VCE

https://drive.google.com/folderview?id=1Wmppx1FSsvkJyMVDTu1lcJ-0iqf7Q9zk

MD5 – F7C5D6E24BCCA7DB10BA157210C241F4
SHA1 – 2AEB69D5294E066AA36B251C61606EDC7EDC984D

IPV6 OSPF Virtual -Link lab Please explain.

Configuration of R4 if we disable this command on R4
area 54 virtual-link 3.3.3.3
We cannot ping form R1
Then we give two command at
R4.
interface loopback 0
IPV6 OSPF 1 area 54
R1.
interface loopback 0
IPV6 OSPF 1 area 0
then we can ping from R1 to R4

Policy based Routing Lab

I follow same steps as guided for configuration but still at the end when i check with command
Show route-map
There is 0 packets against policy routing matches. ??????

i give command at host for check . traceroute

@MZ

please explain ospf virtual link lab. I cannot ping from R1 TO R4 after giving
no area 54 virtual-link 3.3.3.3

command at R4

so the dump by @nneettwwrrookkiinnggg has pdf which has loads of questions but the VCE has this and a section with 195. is this the latest questions we need to worry about?

what page can i find the 195q dump on?

@nitram10

210 and 211

Please explain LABS solution of. The way explain here is not correct at the end test fail.

PBR
&
Virtual_Link

anyone who took exam recently confirm 195q dump and labs from here will be enough please?

Thanks

Any body passed exam recently please explain PBR and Virtual Link labs. My exam after 2 days.

Given solution not work.

Hi all the pass
Congratulations 😊
I helped lots of people so I soo tired 😓

@nneettwwoorrkkiinngg

Q348
!
R2(Config-if)#tunnel mode ipv6ip

A user calls from another branch office with a request to establish a simple VPN tunel to test a new router’s tunneling capability.
Based on the configuration in the exhibit, which type of tunnel was configured?
Answer C:
6to4 Tunnel

Doesn’t seem right answer….can anyone confirm?
Tunnel mode ipv6ip = Manual IPv6 Tunnel
Tunnel mode GRE IP (or just Tunnel Mode) = GRE Tunnel
Tunnel mode ipv6ip 6to4 = 6to4 Tunnel
Tunnel mode ipv6ip ISATAP – Isatap Tunnel

@nneettwwoorrkkiinngg

Please help with PBR and Virtual Link labs

Solutions are not working . test fail.

IPV6 OSPF Virtual Link
If we disable R4 with no area 54 virtual-link 3.3.3.3 then we cannot ping from R1

@pk, anonymous, kaleem

For the PBR lab the solution is correct. If is not working you have configured something wrong.
Can you ping ISP1 & ISP2 from the host? If not, then you have a configuration issue. If you can ping both ISPs and just not policy route, then something is wrong with your policy or ACL.

If you are certain that you have configured everything correct, then here is a hint to your problem: What traffic is the ACL matching?

@pk.. did you try ping ipv6 FEC0:4::4 from R1 ? i just tried and its working

@ Mizo

QUESTION 709
which access list used to filter upper layer protocol ?
A. extended acl
B. standart acl
C. reflexive acl
D. time based acl
E. dynamic acl

Im going with……
Extended – Upper-layer protocol
Reflective – Upper-layer session information

Extended ACL
An extended access-list is an ordered list of statements that can deny or permit packets
based on source and destination IP address, port numbers and upper-layer protocols

Reflective ACL
Reflexive ACLs allow IP packets to be filtered based on upper-layer session information

@anonymous
Actually if we give following command at R4 for full marks as mentioned in question.

no area 54 virtual-link 3.3.3.3 then ping not work.

@anonymous
Actually if we give following command at R4 for full marks as mentioned in question.

no area 54 virtual-link 3.3.3.3 then ping not work

Please send command solution at kaleemkhawarksa at gmail com

Fail with 6xx/1000
Labs of EIGRP STUB, OSPF virtual link and redistribution between ospf and eigrp.
I used the examcollection dumps and none of the questions shows up. That was my problem.
I will try again soon.