Share your ROUTE v2.0 Experience

Is it fair to assume learning all the COMPOSITE quiz (all 15 of them) from this website will be adequate to pass ??

Along with all the simulations and D&D’s ??

what happened to the member login ???

Passed CCNP route yesterday. There are lots of new questions.
Labs are from here and drag & drop.
I almost failed, got 802 and pass mark is 790. Study very hard.. All I can say this site is not enough to pass unless you go for membership…
Best of Luck to everyone.. Tshoot next..
Ping me @ m.cha.nca.rd70.g.m.ail.com remove the dots

Avoid buying dumps… do more research

thanks to 2604
so DHCP scope 82 – additional security used on untrusted sources

SNMP traps vs SNMP informs – both are almost same, with informs we have nothing more than acknowledgement

Limitation of RIPV2 when deploy in a supernets network – here i am not sure , RIPv2 is classless , supernets are classfull so can they be advertised in RIPv2 ?

Is it fair to assume the labs in the exam will still be the EIGRP-OSPF Redistribution, PBR & OSPF Evaluation ??

I think YourMom mentioned it’ll just be those 3 in one of the previous pages.

Can anyone share the latest dumps commandlineclown(at)gmail.com

does anyone has exam on Monday ? pls share feedback , if questions are same etc

Which two pieces of information can you learn by viewing the routing table?

A. Whether an ACL was applied inbound or outbound to an interface
B. Whether the administrative distance was manually or dynamically configured
C. Which neighbor adjacencies are established
D. The EIGRP or BGP autonomous system
E. The length of time that a route has been known

E B

Which two facts must you take into account when you deploy PPPoE interface?

A. DDR idle timers must be configured to support VPDN loggin
B. PPPoE supwports a maximum of 10 clients per customer premises equipment
C. DDR is not supported
D. You must manually configure IP addresses on the PPPoE interface
E. An individual PVC can support one PPPoE client

B E

Hello,

I passed the exam today (985/1000), I got :

– 3 Labs: EIGRP stub, PBR, EIGRP eval
– 6 DNDs: DHCP, adverse network conditions, AAA, Frame-relay component and LMO, TACACS+ACL

All the questions were from this dump (Updated this month with the new questions)

https://www.cjoint.com/doc/19_05/IEmwKooUlhy_300-101.pdf

What type of address OSPFv3 uses to form adjacency and send updates?
A FF02::5
B link-local
C IPv4 address
D IPv6 address multicast

Dump Say C but my research says it should be A or D? please help.

Can anyone send me the last dump at my mail.
ayman_salem89(at)hotmail. Com

HERE YOU GO. Passing examz now easy.

CCNA 200-125
CCNP ROUTE 300-101
CCNP SWITCH 300-115
CCNP TSHOOT 300-135
CCIE R&S 400-101

AT BELOW LINK:
R E M O V E-S P A C E S

t2 m . io/qkhTw5dQ

ATTENTION ALL!!!

ATTENTION ALL!!!

ATTENTION ALL!!!

300-101 exam passed on 10/May/2019!!!

8xx points!!!

Drag and Drop:
– aaa radius auth/authorization/acconting
– aaa krb5 goups ecc
– chap pap
– ipv6

LAB:
– eigrp ospf redistribute
– pbr
– eigrp evaluation

Mainly learned the latest Pass Leader 300-101 dumps (~~~769q NEW VERSION UPDATED in May/2019~~~), stable and valid enough for passing!

Good luck!!!

It’s actually A, that’s the correct answer from my research & study too.

The compositive quiz part says “We have 15 composite quizzes currently, each comprises of 50 questions of all topics of CCNP ROUTE 300-101. If you can pass all of them then congratulation, you have full knowledge for the new ROUTE exam.”
But then other people on here commenting, saying to do the Most Popular Questions (MPQ).

This is confusing. I think one should be taken off if the other is more appropriate.

So what do we do, Composite or MPQ ?? Because they seem to overlap.

and I just finished painstakingly done the composites. All 15 of them. Would that be ok to pass the exam (along with labs ofcourse) or am I being misled ??

Ebraheem IS FAKE FAKE FAKE ..

Ebraheem IS FAKE FAKE FAKE ..

DON’T USE Ebraheem FAKE FAKE FAKE DUMPS

Hi David;

Would you please share me 300-101 dump 769q May/2019. Thanks alot

my e ma il: ccnp 3 2 90@ g m ail . com

Hi all, MQ means ?

Hello David Gonzalo,

Could you please share your dumps with me?

my email is www dot cisco at gmail dot com

Please
Best Regards
WWDT

Ebrahim bro, could you please share latest dumps 300-101 at rahimullah843(at)gmail(dot)com
i am in preparation step for the exam i will be very much thankful to you .

This is a pleasant weekend. I passed the CCNP 300-101 exam. I think I need to recommend this stable and effective material website to everyone.
Dump type: CCNA, CCNP, CCIE and cissp
Account Type: Routing and Switching, Security, Wireless, Data Center, Service Provider, Collaboration, Design
http://www.aimpass.com/cisco_300_115_switch.php?utm_source=luntan0010100

You are implementing WAN access for an enterprise network while running applications that require a fully meshed network, which two design standards are appropriate for such an environment?

A. A centralized DMVPN solution to simplify connectivity for the enterprise
B. A dedicated WAN distribution layer to consolidate connectivity to remote sites
C. A collapsed core and distribution layer to minimize costs
D. Multiple MPLS VPN connections with static routing
E. Multiple MPLS VPN connections with dynamic routing

A B

Which task do you need to perform first when you configure IP SLA to troubleshoot a network connectivity issue?

A. Specify the test frequency
B. Enable the ICMP echo operation
C. Schedule the ICMP echo operation
D. Verify the ICMP echo operation

B

Which technology can combine multiple physical switches into one logical switch?

A. HSRP
B. VSS
C. VRRP
D. NHRP

Which two features are compatible with port security?

A. Voice VLAN
B. SPAN source port
C. DTP

What are two reasons to use multicast to deliver video traffic, instead of unicast or broadcast?

A. It provides reliable TCP transport
B. It enable multiple servers to send video streams simultaneously
C. It enable multiple clients to send video streams simultaneously
D. It supports distributed applications
E. It enable multiple clients to receive video streams simultaneously

D E

Which two statements about PAP authentication in a PPP environment are true?

A. It is performed at the beginning of the session only
B. It sends the password in clear text
C. It uses a username with an MD5 password to authenticate
D. It hashes the password before sending it
E. It is performed at the beginning of the session and is repeated periodically for as long as the session is maintained

B E

Which two tasks should you perform to begin troubleshooting a network problem?

A. Gather all the facts
B. Define the problem as a set of symptoms and causes
C. Implement an action plan
D. Monitor and verify the resolution
E. Analyze the results

A B

Which two pieces of information can you learn by viewing the routing table?

A. Whether an ACL was applied inbound or outbound to an interface
B. Whether the administrative distance was manually or dynamically configured
C. Which neighbor adjacencies are established
D. The EIGRP or BGP autonomous system
E. The length of time that a route has been known

E B

Which two facts must you take into account when you deploy PPPoE interface?

A. DDR idle timers must be configured to support VPDN loggin
B. PPPoE supports a maximum of 10 clients per customer premises equipment
C. DDR is not supported
D. You must manually configure IP addresses on the PPPoE interface
E. An individual PVC can support one PPPoE client

B E

Which fallback method can you configure to allow all AAA authorization requests to be granted if the other methods do not respond or return an error?

A. Radius
B. Enable
C. TACACS+
D. NONE

D

By default what is the maximum number of equal metric path BGP uses for load balancing?

Up to a maximum of 6

Which difference idn the packet fragmentation feature between IPv4 and IPv6 is true?

There is no fragmentation in IPv6 because it uses Path MTU Discovery in order to find the smallest packet size to the destination.

Which LAN features enable a default gateway to inform it’s end devices when a better path to a destination is available?

ICMP redirect

The track objects in IP SLA and make sure that it is only up if all track objects are up, which method achieves that goal?

A. AND
B. OR
C. XOR
D. ???

A

With PCA and PCB and there are three routers between them and a different MTU value and they want a PCA to run an application with PCB and DF is set so we have to choose?

A. MSS
B. PMTU
C. GRE
D. ???

A

Done my test and got certification 962

LABS: EIGRP STUB, EIGRP-OSPF REDIST, IPv6 OSPF VL & OSPF
EVAL: OSPF
DND: NAT64, uRPF modes, ACL, COPP/MSS, FRAME RELAY

Without Stars***
https:/*/urlzs.*com/TQbN

Which two statements about PAP authentication in a PPP environment are true?

A. It is performed at the beginning of the session only
B. It sends the password in clear text
C. It uses a username with an MD5 password to authenticate
D. It hashes the password before sending it
E. It is performed at the beginning of the session and is repeated periodically for as long as the session is maintained

B E

Which two tasks should you perform to begin troubleshooting a network problem?

A. Gather all the facts
B. Define the problem as a set of symptoms and causes
C. Implement an action plan
D. Monitor and verify the resolution
E. Analyze the results

A B

ip dhcp relay information option –> add suboption and the remote ID suboption

ip dhcp relay information check –> Verify relay information option (in forwarded BOOTREPLY)

ip dhcp relay information policy …… –> Define reforwarding rules (for a DHCP relay agent)

ip dhcp relay information subscriber-id –> enable a service provider to add a unique ID

ip dhcp relay information –> configured in global configuration mode applies to all interface

Please help me. Is it correct!

Hi,

i have my route exam at end of june 2019. Please send me the latest dumps for 300-101 as pdf and if available vce file to following email om4bpa4ziid(at)temp(dot)mailbox(dot)org
Thanks in advance.

hi, i got confused with the correct answer. some say A, some say D which is the real correct answer?

Company is deploying a multicast application that must be accessible between sites, but must not be accessible outside of the organization. Based on the scoping requirements, the multicast group address for the application will be allocated out of which range?

A) FF02:/16
B) FF0E:/16
C) FF00:/16
D) FF08:/16

@yorke

D- > correct because FF08:
Because its about entire organization not restricted to particular physical link which is Link-local address

ip dhcp relay information option –> add suboption and the remote ID suboption

ip dhcp relay information check –> Verify relay information option (in forwarded BOOTREPLY)

ip dhcp relay information policy …… –> Define reforwarding rules (for a DHCP relay agent)

ip dhcp relay information subscriber-id –> enable a service provider to add a unique ID

ip dhcp relay information –> configured in global configuration mode applies to all interface

Please help me, I dont know it correct ?. please

@Jack

First of all where did u get this question ? cisco IOS v 15.6 reveals the following option with context help in real cisco router..

R1(config)#ip dhcp relay information ?
check Validate relay information in BOOTREPLY
option Insert relay information in BOOTREQUEST
policy Define reforwarding policy
trust-all Received DHCP packets may contain relay info option with zero
giaddr
———————————————————–

R1(config)#ip dhcp relay information option ?
vpn Insert VPN sub-options and change the giaddr to the outgoing interface

In the following example, the DHCP relay receives a DHCP request on ethernet 0/1 and sends the request to the DHCP server located at IP helper address 10.44.23.7, which is associated with the VRF named “red”.

ip dhcp relay information option vpn
interface ethernet 0/1
ip helper-address vrf red 10.44.23.7

your options are correct. let me know where did you find it ? which dump site ?

Thanks you. Saji
I using dump chinna and dump passleader. But all different answer.
Question : Multi choice column A and column B.
ip dhcp relay information option –> add suboption and the remote ID suboption

ip dhcp relay information check –> Verify relay information option (in forwarded BOOTREPLY)

ip dhcp relay information policy …… –> Define reforwarding rules (for a DHCP relay agent)

ip dhcp relay information subscriber-id –> enable a service provider to add a unique ID

ip dhcp relay information –> configured in global configuration mode applies to all interface

Thanks you Saji.
I used Chinese and Passleasder dump. But all different Ans. So I need verify Ans.

Thanks

@Jack, I know it will be very annoying question but where did you find Chinese and Passleader dumps? I am a premium member here but didn’t see them there. Is there any chance to upload them anywhere to share? I am not a lazy ass as most of people asking for free dumps so I will just understand if you ignore that – Appreciate in advance your help :)

@Jack – how to get those questions? Are there different than digitaltut ones?

Hello everyone, i recertified on 9th of may with 925/1000.
I got PBR, OSPF eval and another I dont remember (same old ones thou).
Questions, almost everything was covered here, except for the TTL dnd mentioned somewhere in the comments and 2 or 3 questions (very easy).
The questions were mainly from MPQ and some from older pool, but everything here.
Still, I studied from videos & dived deep on some things I was weak.

Good luck everyone!

Which scenario can asymmetric routing occur?

A -> active/active firewall
B -> single path in and out of network
C -> active/stadby firewall
D -> redundant routers using vrrp

Some say answer is A and others D, please help with this question

Which protocol will stop listening and advertising updates, when using passive-interface command.
A. OSPF
B. EIGRP
C. BGP
D. RIP
E. IS-IS
Answer: A and B

Explanation:
Passive-interface command is used in all routing protocols to disable sending updates out from a specific interface. However the command behavior varies from o­ne protocol to another.

In RIP this command will disable sending multicast updates via a specific interface but will allow listening to incoming updates from other RIP speaking neighbors. This simply means that the router will still be able to receive updates o­n that passive interface and use them in the routing table.

In EIGRP the passive-interface command stops sending outgoing hello packets, hence the router can not form any neighbor relationship via the passive interface. This behavior stops both outgoing and incoming routing updates.

In OSPF the passive-interface has a similar behavior to EIGRP. The command suppresses hello packets and hence neighbor relationships.

What type of address OSPFv3 uses to form adjacency and send updates?
A FF02::5
B link-local
C IPv4 address
D IPv6 address multicast

Correct Answer: A (same if converted as 224.0.0.5 ipv4 multicast for OSPF DR router)

Company is deploying a multicast application that must be accessible between sites, but must not be accessible outside of the organization. Based on the scoping requirements, the multicast group address for the application will be allocated out of which range?

A) FF02:/16
B) FF0E:/16
C) FF00:/16
D) FF08:/16

Answer: I agree with D)FF08:/16 – Organization scope: Intended to span multiple sizes within the same organization

Source: https://ipv6friday.org/blog/2011/12/ipv6-multicast/

Which two features are compatible with port security?
A. Voice VLAN
B. SPAN source port
C. DTP

Guys what is the answer for this, all dumps with this ques came without anser

Excessive unicast flooding condition: >>>caused by including a host port in STP
Out-of-order packets: >>>potential result of disabling FIFO
TCP starvation: >>>>potential effect of excessive UDP traffic on link
Asymmetric routing:>>> cause of inconsistent traffic patterns
Latency: >>>condition in which packets require an excessive length of time to traverse a switch

Hi guy. please help me Ans question. I am reading Chinese dump and Passleader dump but It have diffrent Ans.
Please help me verify help me.

A and B
You can find other compatible features on the link below. (Table 3)
https://www.cisco.com/en/US/docs/switches/lan/catalyst3850/software/release/3.2_0_se/multibook/configuration_guide/b_consolidated_config_guide_3850_chapter_011111.html

If you don’t have an answer or doubtful of any dumps that you are using, you can always search google and for sure Cisco will have a whitepaper or documentation. Just have to understand each concept to easily find what you are looking for. Good luck

@macking
Ospfv3 doesn’t work the way the ipv4 works. It alway uses link local address to send updates and notifications.
When i lab it up with real gears it only use ff0::5 for to find the ospf speaking neighbors after that it always uses link local address to send updates (question sending updates). Even cisco literatures says so.
I would select the link local address. We can not interprete the ospv4 into ospfv3 since it behave differently

@Saji, I did not mean they work the same way. It is my way of remembering that :5 in ospfv3 is the same .5 in ospf. Just the Hex number is the same as the last octet on the multicast IPv4.

I will be seating for exam on the 18th and just now I feel ready and equipped. Thanks of course with the help of digitaltut and the unselfish members in here willing to share their experience. I will for sure return the favor and hopefully my mind will be open enough to remember new questions (if any) for the benefit and exam of the next exam takers. I think that what makes this website still successful now. Just appealing to those scammers, please stop. The people here are professional enough to know what you are doing.

OSPFv2 and OSPFv3 both have the same protocol number of 89, although OSPFv3, being an IPv6 protocol, more accurately has a Next Header value of 89. And like OSPFv2, OSPFv3 uses multicast whenever possible. The IPv6 AllSPFRouters multicast address is FF02::5, and the AllDRouters multicast address is FF02::6.
Source: https://www.networkworld.com/article/2298648/chapter-9–ospfv3.html

Took the test today and failed. Around 12-15 new questions that I have not seen here on the site. Mind you I am a premium member and I went over with MPQ, NUQ5, NUQ6, Dexter dumps. 6 drag and drop LMI/Frame Relay, NTP64,Strict mode/Loose Mode, Tacacs+, IPv4 NAT. Labs OSPF eval, OSPF Eigrp Redistribution, PBR. Labs and D&D are same from this site. I got confused with new questions about EVN, IPV6, Frame Relay etc. Guys I am not trying to scare anyone but make sure you cover EVN, IPV6, Frame Relay pretty good. I will keep posting about whatever I will remember. Good luck to people who take test next.

That is unfortunate and sad to hear @Saaein. Thanks though, I get pretty much confuse with those topics too so I focused on them with using other study resources. Hope your score is not too far from the passing and you will be able to pull it through next time.

@ All,

Just to clarify !!!
Valid range for BGP private ASNs?
A. 64512-65535
B. 1-64000
C. 64512-65534 ——>>> correct answer <<<<<<—

https : // networklessons.com /bgp/bgp-private-and- public-as- range

share exam questions 300-101
passhot dot com