Share your ROUTE v2.0 Experience

Can anyone plz share the lab question with solution ? plz help me …

many thnx @ tut-user!

Hi Guys,
i have a quick question about the Labs in the exam about EIRGP Stub or others.
i checked abouve Fourm lots of issues in the exams i also had same expericened last week.

If anybody already passed exam and successfully done labs/new Questions please share experience or exact detail of command and what was the exact command for ip summary to write(I applied this in the exam but it didn’t summarize the routes into one. As @crowbar said)

it would really be a great help to CCNP route exam pass.

Thanks

At all who had issues summarizing in the EIGRP SIM in the exam, did you use the same command on this site and it didn’t work or you used a totally different command to summarize.

What are the two benefits of BGP peer groups?
a. support groups of paths
b. A configuration change can be applied simultaneously to all peers in the peer group
c. optimize backdoor routes
d. updated via multicast
e. each neighbour in a peer group can have different inbound BGP Policies
f. they use soft updates to minimize bandwidth consumption
B,E or B,F
Yes, “You can customize the inbound update policy for any member of a peer group”, BUT it’s asks about BENEFITS!
“The major benefit you achieve when you specify a BGP peer group is that a BGP peer group reduces the amount of system resources (CPU and memory) necessary in an update generation”–> soft updates (E)??
” In addition, a BGP peer group also simplifies the BGP configuration.” –> also B
https://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/13755-29.pdf
I’m not sure about that..

@doka
i’ll go B and F

People, anyone have got the correct answers for below 3 please ?

Which three methods can a network engineer use to fix a metric based routing loop in the network.
a. Implement offset lists at network boundaries
b. Filter routes manually using distribute lists
c. Filter routes manually using prefix lists
d. Implement proper network summarisation on key routing points
e. Filter routes based on tags
f. Utilise root database filters

Which two features are added in MSCHAP Version 2
a. Backwards-compatibility with MSCHAP version 1
b. Using the MD5 hash for stronger security
c. Ability to change an expired password
d. using 3 way handshakes for authentication
e. mutual authentication between peers

What is a function of NPTv6?
A. It interferes with encryption of the full IP payload.
B. It maintains a per-node state.
C. It is checksum-neutral.
D. It rewrites transport layer headers.

and this is too pls:

When use NPTv6 for IPV6 to IPV6 Address translation? (Choose two)
A. stateful address translation
B. a limit of 32 1-to-1 translations
C. lack of overloading functionality
D. identify all interfaces NAT inside or outside
E. 1-to-1 prefix rewrite
F. mismatched prefix allocations

@Routeontheway

3)What is a function of NPTv6?
A. It interferes with encryption of the full IP payload.
B. It maintains a per-node state.
C. It is checksum-neutral.
D. It rewrites transport layer headers.
Correct Answer: C

4)What are two limitations when in use of NPTv6 for IPV6 vs IPV6 Address translation?
A. stateful address translation
B. a limit of 32 1-to-1 translations
C. lack of overloading functionality
D. identify all interfaces NAT inside or outside
E. 1-to-1 prefix rewrite
F. mismatched prefix allocations
Correct Answer: C,F

Please who has a link to the clearer version of Kikavich DND…in the link posted earlier, most of the answers were cut off and some are really not clear. I will really appreciate it. Thank you

@@Routeontheway
Which two features are added in MSCHAP Version 2
a. Backwards-compatibility with MSCHAP version 1
b. Using the MD5 hash for stronger security
c. Ability to change an expired password
d. using 3 way handshakes for authentication
e. mutual authentication between peers

Answer:-CE

Explanation :-

Note:- MSCHAP V2 authentication is an updated version of MSCHAP that is similar to but incompatible with MSCHAP Version 1 (V1). MSCHAP V2 introduces mutual authentication between peers and a Change Password feature.

https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/sec_usr_aaa/configuration/15-mt/sec-usr-aaa-15-mt-book/mschap_version_2.html#GUID-DCB20ADF-1F8E-434B-AE97-54802879F34F

@sambugoyski

Will Concentrix pay for your certification?

@poo

If anybody already passed exam and successfully done labs/new Questions please share experience or exact detail of command and what was the exact command for ip summary to write(I applied this in the exam but it didn’t summarize the routes into one. As @crowbar said)

———
ip summary-address eigrp 100 10.2.0.0 255.255.0.0
* I tried the /20 as well, but it’s not summarizing any

Hi,
Can anybody guide me which dumps are valid from Following to pass the exam?
1-Dextor
2-Jazzy
3- Prince 91
Thanks and regards

Passey exam today.
New questions mentioned on previous pages are valid and I got like 10-15 news questions which were not from dumps.
Labs: Eigrp stub, redistribution, ipv6 ospf

@Preet
did you remember that 10-15 new questions which were not this form of dump.

It would really be a great help.

@tut_user
Thanks for your feedback.
Do you have any suggestions how should i sucessfully finsh this EIGRP Stub Sim if /20 didnot work for you ?

Thanks

I passed 900.
477 and page 147-8 enough

@CCNP Route Exam
1. ospf sim it was the normal one.
2. DND frame relay, ACL, AAA , GRE
3. sorry i dont remember exactly but somthing about AAA and BGP
don’t worry about the time it’s more than enough PS: my english is not perfect ;)
i finished all the exam less than one hour with high score
Good Luck

here is some questions appeared in my exam

Which condition prevents the establishment of a DMPVN tunnel between two spokes?
a. HSRP is enabled on the spoke devices
b. IPsec is enabled on the spoke devices
c. the two spokes are behind different PAT devices
d. the two spokes have different tunnel keepalive settings.

What are the two benefits of BGP peer groups
a. support groups of paths
b. A configuration change can be applied simultaneously to all peers in the peer group
c. optimize backdoor routes
d. updated via multicast
e. each neighbour in a peer group can have different inbound BGP Policies
f. they use soft updates to minimize bandwidth consumption

Which feature is supported with stateful NAT64 ?
a. IP multicast
b. NAT44 and NAT64 on the same interface
c. VRF
d. FTP and ICMP on an application layer gateway

which routing protocol searches for a better route through other autonomous systems
to achieve convergence ?
a. Link-state
b. Hybrid
c. Path vector
d. Distance vector

which condition prevents the establishment of a DMPVN tunnel between two spokes ?
a. HSRP is enabled on the spoke devices
b. IPsec is enabled on the spoke devices
c. the two spokes are behind different PAT devices
d. the two spokes have different tunnel keepalive settings

multicast application must be accessible between sites, but not be accessible outside of the organisation. Based on the scoping requirements, the multicast group address for the application will be allocated out of which range ?

a. FF00::/16
b. FF08::/16
c. FF02::/16
d. FF0E::/16

good luck to all
and thanks for digitaltut

this also

for RIPv2 how long a static route remains if the point to point interface is down.
a 30s
b 60s
c 180s
d 240s

What is the default authentication in RIPv2 when authentication is enabled

A. SHA1 authentication
B. Enable password authentication
C. Plain text authentication
D. MD5 authentication

25. Which two tasks does a DHCP relay agent perform? (Choose two)

A. It forwards DHCPHELLO and DHCPREQUEST messages to the DHCP server
B. It forwards DCHPREQUEST and DHCPACK messages to the DHCP server
C. It forwards DHCPOFFER and DHCPCOMPLETE messages to the DHCP server
D. It forwards DHCPDISCOVER and DHCPREQUEST messages to the DHCP server
E. It forwards DHCPOFFER and DHCPACK messages to the DCHP server

Where must a network engineer configure the ip helper-address command on a router

a. On the interface that will receive the broadcasts
b. On the DHCP configuration
c. the interface that is closed to the destination DHCP server
d. on the global configuration mode

Thnx @Poo and Aisha
@tut-user….perhaps you applied summary on wrong interface ? do you happened to remember exact ip ? was it class A address ? in a EIGRP stub lab, you suppose to run “sh runn-config” to get ip’s first…..also if you sure that put all the config in 2 routers correctly? however, if you have done all above and still didn’t work, than am assuming it just because you had glitch in your lab!

@ Aisa, Preet and Thanksmario
do you guys remember how did you summarize ip for EIGRP stub lab?
and happened to remember IP add and subnet mask pls..

@aisha

Thanks for your feedback!
By the way, can you advise which answer you selectED for the list of new questions you posted below?
Thanks.

Which condition prevents the establishment of a DMPVN tunnel between two spokes?
a. HSRP is enabled on the spoke devices
b. IPsec is enabled on the spoke devices
c. the two spokes are behind different PAT devices
d. the two spokes have different tunnel keepalive settings.

C

What are the two benefits of BGP peer groups
a. support groups of paths
b. A configuration change can be applied simultaneously to all peers in the peer group
c. optimize backdoor routes
d. updated via multicast
e. each neighbour in a peer group can have different inbound BGP Policies
f. they use soft updates to minimize bandwidth consumption

BF

Which feature is supported with stateful NAT64 ?
a. IP multicast
b. NAT44 and NAT64 on the same interface
c. VRF
d. FTP and ICMP on an application layer gateway

C

which routing protocol searches for a better route through other autonomous systems
to achieve convergence ?
a. Link-state
b. Hybrid
c. Path vector
d. Distance vector

C

which condition prevents the establishment of a DMPVN tunnel between two spokes ?
a. HSRP is enabled on the spoke devices
b. IPsec is enabled on the spoke devices
c. the two spokes are behind different PAT devices
d. the two spokes have different tunnel keepalive settings

C

multicast application must be accessible between sites, but not be accessible outside of the organisation. Based on the scoping requirements, the multicast group address for the application will be allocated out of which range ?
a. FF00::/16
b. FF08::/16
c. FF02::/16
d. FF0E::/16

B

for RIPv2 how long a static route remains if the point to point interface is down.
a 30s
b 60s
c 180s
d 240s

D

What is the default authentication in RIPv2 when authentication is enabled
A. SHA1 authentication
B. Enable password authentication
C. Plain text authentication
D. MD5 authentication

C

25. Which two tasks does a DHCP relay agent perform? (Choose two)
A. It forwards DHCPHELLO and DHCPREQUEST messages to the DHCP server
B. It forwards DCHPREQUEST and DHCPACK messages to the DHCP server
C. It forwards DHCPOFFER and DHCPCOMPLETE messages to the DHCP server
D. It forwards DHCPDISCOVER and DHCPREQUEST messages to the DHCP server
E. It forwards DHCPOFFER and DHCPACK messages to the DCHP server

DE

Where must a network engineer configure the ip helper-address command on a router
a. On the interface that will receive the broadcasts
b. On the DHCP configuration
c. the interface that is closed to the destination DHCP server
d. on the global configuration mode

A

For the eigrp stub lab sim,

which command you guys used for summarization for list of IP range from 10.2.2.x – 10.2.9.x?

ip summary-address eigrp ASN 10.2.0.0 255.255.0.0

or

ip summary-address eigrp ASN 10.2.0.0 255.255.240.0

Is wr mem/ copy run start working in your exam labs?

Which statements indicate a valid association mode for NTP synchronization?
A. The client polls NTP servers for time.

B. The client broadcasts NTP requests.

C. The client listens to NTP broadcasts.

D. The client creates a VPN tunnel to an NTP server.

any one get this in exam?

E. The client multicasts NTP requests.

previous question

@CCNP ROUTE Exam
that was my answers :)
@Routeontheway i accept what you saying about everyone should be careful about this points summary on wrong interface, ip address range , dont forget to check the interface before.
i think the range was 10.2.0.0 255.255.0.0 the full command ip summary-address eigrp 123 10.2.0.0 255.255.0.0
if you have any questions don’t hesitate to ask im ready to answer as much as i can
allah bless you

@all
PS: digitaltut recently added an old EIGRP Simlet on this link i didnt had this one in my exam but its ok if you cover it http : // www . digitaltut.com/ route-eigrp-simlet

Many thnx CCNP Route Exam and Aisha …..
and may GOD bless you too @Aisha…..whats going to be your next attemp…tshoot, may b ?

Correct answer for below pls ?

Which three methods can a network engineer use to fix a metric based routing loop in the network.
a. Implement offset lists at network boundaries
b. Filter routes manually using distribute lists
c. Filter routes manually using prefix lists
d. Implement proper network summarisation on key routing points
e. Filter routes based on tags
f. Utilise root database filters

@Routeontheway – question is a bit vague, that is the reason no one knows the exact correct answer. As I understand it they mean loops caused by redistributing back the learned routes but now with better metric due to protocol preference, e.g. OSPF distributes to EIGRP some route, EIGRP learns it and then redistributes it back to OSPF as External EIGRP route , given that admin distance of OSPF is 110 and of EIGRP 90 the OSPF process will learn its own route as available via EIGRP causing the loop. The remedy here is to filter routes when redistributing, problem is that it can be done in many ways depending on the routing protocols, so to me a,b,c,e seem legit , but need to pick just 3…

Hi All, passed successfully, few tips:
– Are the dumps + labs enough to pass ? Yes, but by a very slim margin and heavily depends on luck, if you have no idea what the Frame Relay is, what are distances/metrics used in EIGRP/OSPF/Ripv2/Ripng , but just try and memorize all the dumps and labs – most probably you will fail, as Cisco throw 9-10 new questions weekly into the exam, most of them quite easy but again, easy if you know fundamentals. After all – 80% of the blueprint is old as the world – so Cisco can re-use thousands of questions from the last 10 years and no dump will ever be 100% correct. So my tip here – yes, use the dumps but more to validate your knowledge than pass the exam. I, for example, could answer about 70% of the questions in dumps not looking at the possible answers at all, and still haven’t got 1000/1000.
– Simulations. Do not try to just memorize commands, try to actually understand what those commands do. As exam have room for changes – interface names, IP addresses, subnet masks, and if you fail Sim(s) you fail exam. And yes, all the simulation here on digitaltut are valid, I’ve got Redistribution OSPF/EIGRP and OSPFv6 virtual-link one as everyone else.

– Copy run start. This option has been disabled for few years now! You either get error or “Not implemented” message when trying to save configs – no need, once finsihed just click Next.

– Valid dumps: Kikavich + 477 Questions + Kikavich DND. There are new DNDs – look for Mario comments here. As I said it will give you some 70-80% answers on the actual exam. Added new DND as Mario said for MPP/Frame Relay – to answer it know how to configure Frame Relay multipoint interface (something along config t -> interface serial0/0 -> encapsulation frame-relay -> no ip address -> interface Serial0/0.1 multipoint -> ip address -> something about frame-relay map.)

– On Sims always use the verification commands, Sims have bugs which may inadvertendly remove your configs etc – after you finished the configuration, verify the status, then click Next!

– Show run – I had it available on all Sims.

– Premium membership on digitaltut – actually I paid it to support the site, but haven’t used it (as opposed to TSHOOT – there you pretty much have to have the Premium for the tickets practice).

Thanks to all who shared the experience here and good luck to testers!

@aishah

Thanks and appreciated!

@Student A, Routeontheway

I think the correct answer for below question should be ACE in term of fixing metric of redistributed routes which could be related with route-map. Offset-list is to influence metric for distance vector routing protocol, while prefix-list/tag used in route-map. Although distributed-list can apply route-map (distributed-list route-map xxx) but it seem like not what the question need.

Which three methods can a network engineer use to fix a metric based routing loop in the network.
a. Implement offset lists at network boundaries
b. Filter routes manually using distribute lists
c. Filter routes manually using prefix lists
d. Implement proper network summarisation on key routing points
e. Filter routes based on tags
f. Utilise root database filters

@Routeontheway I think my next attemp will be Switching

@all

Can you guys please confirm the answers for below questions? Thanks.

What are two limitations when in use of NPTv6 for lPV6 vs lPV6 Address translation?
A. stateful address translation
B. a limit of 32 1-to-1 translations
C. lack of overloading functionality
D. identify all interfaces NAT inside or outside
E. 1-to-1 prefix rewrite
F. mismatched prefix allocations

CF or CE?

In which scenario can asymmetric routing occur?
A. active/active firewall setup
B. single path in and out of the network.
C. active/standby firewall setup.
D. redundant routers running VRRP.

A?

The following configuration is applied to a router at a branch site: ipv6 dhcp pool dhcp-pool dns-server dns-server domain-name example.com
If IPv6 is configured with default settings on all interfaces on the router, which two dynamic IPv6 addressing mechanisms could you use on end hosts to provide end-to-end connectivity? (Choose two.)
A. EUl-64
B. SLAAC
C. DHCPv6
D. BOOTP

AB?

The enterprise network WAN link has been receiving several denial of service attacks from both IPv4 and IPv6 sources. Which three elements can you use to identify an IPv6 packet via its header, in order to filter future attacks? (Choose three.)
A. Traffic Class
B. Source address
C. Flow Label
D. Hop Limit
E. Destination Address
F. Fragment Offset

BCE?

Other than a working EIGRP configuration, which option must be the same on all routers for EIGRP authentication key role over to work correctly?
A. SMTP
B. SNMP
C. Passwords
D. Time

D?

A network engineer is configuring the router for NetFlow data exporting. What is required in order for NDE to begin exporting data?
A. Source
B. Flow mask
C. Destination
D. Interface type
E. Traffic type
F. NetFlow version

C?

An engineer is using a network sniffer to troubleshoot DHCPv6 between a router and hosts on the
LAN with the following configuration:
Interface EthernetO
Ipv6 dhcp server DHCPSERVERPOOL rapid-commit
Which two DHCPv6 messages will appear in the sniffer logs?
A. reply
B. request
C. advertise
D. acknowledge
E. solicit
F. accept

AE?

Which two reasons for IP SLA tracking failure are likely true? (Choose Two)
A. The source-interface is configured incorrectly.
B. The destination must be 172.30.30.2 for icmpecho.
C. A route back to the RI LAN network is missing in R2.
D. The default route has wrong next hop IP
address.
E. The threshold value is wrong.

A & C? Why C?

Which two GRE features can you configure to prevent fragmentation? (Choose Two)
A. IP MTU
B. MTU ignore
C. TCP MSS
D. UDP windows sizes
E. MTUD
F. DF bit clear

CF?

Refer to the exhibit. A network engineer executes the show ipv6 ospf database command and is presented with the output that is shown. Which flooding scope is referenced in the link-state type?

A. link-local
B. area
C. As (OSPF domain)
D. reserved

A?

An administrator needs to setup an NTP client to provide updates to local without synchronizing to server. What is the command?
A. Serve
B. Serve-only
C. peer

A or B?

A network engineer wants an NTP clients to be able to update the local system without updating or synchronizing with the remote system. Which option for the ntp access-group command is needed to accomplish this?
A. serve
B. query-only
C. serve-only
D. peer

A or C?

Using new backup router in spite of faulty one in ospf domain but relationship with neighbour in one interface only not working , what is the reason of this problem?(choose 2)
A. area Id mismatch
B. authentication mismatch
C. process id of ospf not match
D. ospf timers not match

BD?

TCP traffic is blocked on port 547 between a DHCPv6 relay agent and a DHCPv6 server that is configured for prefix delegation. Which two outcomes will result when the relay agent is rebooted?
(Choose two)
A. Routers will not obtain DHCPv6 prefixes.
B. DHCPv6 clients will b
e unreachable.
C. Hosts will not obtain DHCPv6 addresses.
D. The DHCPv6 relay agent will resume distributing addresses.
E. DHCPv6 address conflicts will occur on downstream clients.

AD? why?

Which three N TP operating modes must the trusted-Key command be configured on for authentication to operate properly? (Choose Three)

A. interface
B. client
C. peer
D. server
E. broadcast

BDE? or BCE?

Which type of address does OSPFv3 use to form neighbor adjacencies and to send LSAs?
A. unicast IPv6 addresses
B. link-local addresses
C. multicast address FF02::5
D. unicast IPv4 addresses

B or C?

Which problem can be caused by latency on a UDP stream?
A. The device that sends the stream is forced to hold data in the buffer for a longer period of time.
B. The overall throughput of the stream is decreased.
C. The device that receives the stream is forced to hold data in the buffer for a longer period of time.
D. The devices at each end of the stream are forced to negotiate a smaller window size.

C?

support a neighbor relationship over an IPv4 internet work. Which three neighbor IP addresses are valid choices to use in the highlighted section of the exhibit? (Choose three.)
A. ::0A43:0002
B. 0A43:0002::
C. ::10.67.0.2
D. 10.67.0.2::
E. 0:0:0:0:0:0:10.67.0.2
F. 10.67.0.2:0:0:0:0:0:0

ACE?

Which statement about this neighbor of RI is true?
A. OSPFv3 adjacency has been lost, which causes the neighbor to be considered Stale.
B. Aggregate global addresses are always used between IPv6 neighbors.
C. OSPFv3 adjacency will not work between link-local addresses.
D. RI used ICMP to learn about this neighbor.

D?

In IPv6, the interfaces running OSPF can be configured with multiple address prefixes.
Which statement is true about the IPv6 addresses that can be included into the OSPF process?
A. Specific addresses cannot be selected for importation into the OSPF process.
B. Specific addresses can be selected using an ACL.
P-185
C. Specific addresses can be selected using a route map.
D. Specific addresses can be selected using a prefix list.

A?

Which interoperability technique implemented on the router would allow Host-I to communicate
with Host-2?
A. Dual Stack
B. NAT-PT
C. 6t04 tunnel
D. GRE tunnel
E. ISATAP tunnel

A?

Which statement is true?
A. RTA will redistribute the RIP routers into the NSSA as type 7 LSAs. RTB will translate the type 7 LSAs into type LSAs and flood them throughout the OSPF backbone.
B. RTA will redistribute the RIP routers into the NSSA as type 7 LSAs. RTB will flood the type 7 LSAs throughout the backbone.
C. RTA will redistribute the RIP routers into the NSSA as type 5 LSAs. RTB will flood the type 5 LSAs throughout the backbone.
D. RTA will redistribute the RIP routers into the NSSA as type 5 LSAs. RTB will translate the type of 5 LSAs unto type 7 LSAs and flood them throughout the OSPF backbone. E. RTA will not redistribute the RIP routers into the NSSA.

A? should be flood into type 5 LSA?

What two situations could require the use of multiple routing protocols? (Choose two)
A. when using UNIX host-based routers
B. when smaller broadcast domains are desired
C. because having multiple routing protocols confuses hackers
D. when migrating from an older Interior Gateway Protocol (IGP) to a new IGP
E. when all equipment is manufactured by Cisco
F. when there are multiple paths to destination networks

AD?

Which statement is correct regarding the operation of NAT-PT between the IPv4 and IPv6 networks shown?
A. The router will determine the IPv4 destination address.
B. The source IPv6 host can use DNS to determine the IPv6-to-lPv4 address mapping.
C. The host is statically configured with the IPv6-to-lPv4 address mapping.
D. ICMP can be used to determine the IPv6-to-lPv4 address mapping.

D?

Which statement about stateless and stateful IPv6 autoconfiguration are true?
A. Both stateless and stateful autoconfiguration require additional setup
B. Stateless autoconfiguration requires no additional setup, whereas stateful autoconfiguration requires additional setup
C. Stateless autoconfiguration requires additional setup, whereas stateful autoconfiguration requires no additional setup
D. Both stateless and stateful autoconfiguration require no additional setup

B?

What are two limitations when in use of NPTv6 for IPV6 vs IPV6 Address translation?
A. stateful address translation
B. a limit of 32 1-to-I translations
C. lack of overloading functionality
D. identify all interfaces NAT inside or outside
E. I-to-I prefix rewrite
F. mismatched prefix allocations

CF?

Which set of actions does a network engineer perform to set the IPv6 address of a DHCP relay server at the VLAN interface level?
A. Enter the VLAN interface configuration mode and define the IPv6 address of a DHCP relay server
B. Enter the global configuration mode and enable the IPv6 DHCP relay
C. Enter the global configuration mode, enable IPv6 DHCP relay from interface configuration mode and define the IPv6 address of a DHCP relay server
D. Enter the VLAN interface configuration mode, enable IPv6 DHCP relay, and define the IPv6 address of a DHCP relay server

D?

Which two types of authentication does EIGRP offer? (Choose two)
A. TI<IP
B. MD5
C. WPA
D. Plain text

B only?

Which three functionalities are specific to stateful NAT64? (Choose Three)
A. It requires IPv4-transalable IPv6 address
B. It requires either manual or DHCPv6 based address assignment for IPv6 host.
C. It helps ensure end-to-end address transparency and scalability.
D. A state or bindings are created on every unique translation.
E. It conserves IPv4 addresses.

DE? why B?

Exam Discount Voucher Available

All exam 62% Discount

CCNA
CCNA Security
CCNP
CCNP Security
Etc

Contact Number : +971547692506

@all

Can you guys please confirm the answers for below questions? Thanks.

What are two limitations when in use of NPTv6 for lPV6 vs lPV6 Address translation?
A. stateful address translation
B. a limit of 32 1-to-1 translations
C. lack of overloading functionality
D. identify all interfaces NAT inside or outside
E. 1-to-1 prefix rewrite
F. mismatched prefix allocations

CF or CE?

In which scenario can asymmetric routing occur?
A. active/active firewall setup
B. single path in and out of the network.
C. active/standby firewall setup.
D. redundant routers running VRRP.

A?

@CCNP Exam route…where did you get above questions from as few of them looks new ?
Thanks for the tips @StudentA

Hi Guys,

I been reading all your comments through this Forum, can someone please advise if “All in One Kikavich” link:https://www.dropbox.com/s/oqd7dept3tdg1vy/all%20in%20one.vce?dl=

Upload here is enough for passing CCNP route Exams, i finish reading the BOOK and Vidoes.

Please advise i have exam in 4 weeks time.

Thanks

John_Snow “Winter is coming”

@John_Snow 4 weeks its more than enough if u already studied the book and the videos
my advice is to try to cover All in One Kikavich and the new Qs in digitaltut

@ Aisha thanks for advise, just wanted to double check dont want surprises

If “All in One Kikavich” is valid enough and new Qs in digitaltut updates in this forum.

Thanks,
John_Snow “Winter is Coming”

can someone pls let me know the verification commands on EIGRP stub lab and how do we check if one link is preferable on to other..
would appreciate your reply.

@Routeontheway
On a router receiving the summarized network # show ip route should show already summed up without any other special distinction except external/from what is distributed if any.
What link is preferred can be seen I guess via #show ip eigrp topology all-links But this command is not implemented in this Sim so alternative is to do traceroute in both directions, this one does work in Sim and shows correct paths

hi guys , i passed the exam today with 94X.
totally 60Q
3 labs : EIGRP OSPF REDISTRIBUTION, OSPF sim and Eigrp Stub.

@routeexam, Congratulation on your CCNP route.

Can you please advise/ share if you use “All in One Kikavich” if so, is it Valid enough for passing ?

Thanks,
John_Snow “Winter is Coming”

@routeexam, Congratulation on your CCNP route.

Can you please advise/ share if you use “All in One Kikavich” if so, is it Valid enough for passing ?

Thanks,
John_Snow “Winter is Coming”

thnx @StudentA
so #tracerouter 172.16.100.1 at R1
and hopefully above syntax will show the packet now going through R1> R2> R3> R4
correct ?

@Routeontheway – yep, I did trace from the leftmost router to rightmost-upper router before I used
(config)# router eigrp ..
(config-rtr)# distance 90 105
And after and it was different path.

Tip for all IPv6 related questions abou t summarization:
only one :: sequence can appear in an IPv6 address and no ::: or :::: etc at all.