Share your ROUTE v2.0 Experience

@Timur what labs specifically?

@studentA the router connecting in between is a serial or ethernet?

I studied with “All in one kikavich ” kikavich 477_corrected and questions posted in this forum. they are all valid.

@ Routeexam congrats
Was the All in one Kikavich Kikavich corrected all you used to pass the exam? you didn’t use any other material?

guys and gurls
any one know the correct syntax/cli command to ping ipv6 loopback address on ipv6 virtual-link lab please ?

Also any specific verification commands for OSPF sim once config is done ?
Am taking exam tomorrow ….

guls and guys…
off to the exam now….will update all a bit later today!

back everyone with the PASS (84X)……yeahhhhh!
had around 6/7 new questions neven seen before but not a matter as long you get your labs and DnD right.
nobody hv a reason for me to stop for a coffeee sip now…..even in this hot weather :)
will be back with more detail.

congrats @Routeontheway.

I’m waiting for full details.

@Routeontheway
Congratulations. Quick question:
Did you study only the “All-in-one” VCE/PDF with about 385 questions. Or did you study the 477 questions VCE/PDF as well?
For anyone that has taken the test recently, do we have to study both of the VCEs or only the latest June 385 questions?
Thanks

for RIPv2 how long a static route remains if the point to point interface is down.
a 30s
b 60s
c 180s
d 240s

if the point to point interface is down, rip neighbor and routing from the neighbor will disappear on 30s, does that mean the answer is A?

can someone give me a valid answer? thanks

@astalavista
The answer is C

so heres the detail.

kikavich 135 and new questions shared earlier on this forum(go back at least 10 pages and you will all find new questions shared by passers) are enough to take Route.

I only happened to remember 2 out of 6/7 new questions, I confronted this afternoon.

1. HOW DEFAULT route config?
a- IP ROUTE command directs to next hop
b- IP ROUTE command directs to next hop and interface
options c and d , i cant remember, unfortunately, but I selected option A as correct.

2. how ospfv3 make neighbourship ?
a- ipv6 neighbourship along with ipv4 (something like that…)
b- ipv6 neighbourship under interface command.
Can’t remember option c & d. but if you read ospfv3 neighbourship topic little bit your good to answer the question.

MY ADVICE:
so far the trend is to throw 5/10 new but easy questions at Route exam…which shouldn’t stop passing route, even if your not genius or bright. the tricky part is to get all 3 labs and DnDs correct though….I had Redistribution(same), Eigrp stub(with same ip but /24 mask) and IPV6 virtual-link(same) labs came in my exam……i literally lost the exam when I had to spent 35 mins on my very first lab (Redistribution). though the labs seems easy but if you haven’t practiced either on gns3 or packet tracer than the chances that you might flip in writing as simple as easy commands on the way…..so ensure to practice the labs properly and your good to concurred Route.

Routeontheway changed to tshootontheway!

Thanks @Routetesttotake and tud…

1. Which BGP option is required when load sharing over multiple equal-bandwidth parallel from a single CE router to a single ISP router over eBGP?
A. eBGP Multipath
B. eBGP Multihop
C. BGP Synchronization
D. Public AS numbers

A or b

16. Which type of Netflow information is displayed when the show ip flow export command is executed?
A. local status and statistics
B. export interface configurations
C. sent status and statistics
D. top talkers
Answer: D or A

54-VPN support for IPv4 and IPv6 address families. Which command

enables a VRF that supports these requirements?
a. Router(config-vrf)#route-target 004:006
B. Router(config)#ip vrf CUSTOMER
C. Router(config)#vrf definition CUSTOMER
D. Router(config-vrf)#rd 004:006

C or A

2. Which routing protocol searches for a better route through other autonomous systems to achieve convergence ?
a. Link-state
b. Hybrid
c. Path vector
d. Distance vector

A or C

@help me please my exam tomorrow
A
A
C
C

for RIPv2 how long a static route remains if the point to point interface is down.
a 30s
b 60s
c 180s
d 240s

Maybe is the question wrong??
what has a static route to do with ripv2?
IMHO “for RIPv2 how long a route remains if the point to point interface is ?”
For me is the answer D correct

@Routeontheway
So to confirm, you did not study the 477 correct?
Thanks for your reply!

@Routetesttotake

the file name is Kikavich 477 but theres only 135 questions in there. so to answer your question, Yes i did study 477.
the 135 are the best selected questions out of 477 by passer named Kikavich. the majority in 477 doesn’t form part of route test anymore.
all the kikavich multiples and drag n drop google drive shared by many in previous pages.

@Routeontheway,
I appreciate you commenting on my question.
Yup, I am currently studying the “All-in-One” that includes the new questions in June, Kikavich477_corrected, and DnDs.
So it sounds like I’m covered with this .VCE and don’t need to study the Jazzy + Prince questions.

si desapruebas el examen se refleja inmediatamente en pearson para dar el mismo examen

if you disapprove the exam is immediately reflected in pearson to give the same exam

@Routetesttotake,

Can you please share the files you are studying via Google?

“All-in-One” that includes the new questions in June, Kikavich477_corrected, and DnDs.”

Thank you

@doka

you can try it on some lab or gns3, if the point to point interface is down in ripv2, the route will disappear after 30s.

@astalavista
Yes, but only if “route poisoning/ poisoned reverse” works. then metric 16 –> 30 sec correct
BUT the question is not clear!

How is it possible that someone had 53q and someone had 60q?? :D :D

@Routeontheway So you mean that the 135Qs are enough to pass ? thank you so much

@astalavista
@doka
so which one is the correct answer? D?

Don’t take any answer for granted. Make sure you do your own research. Even if you just google the question you will see at least 2 or 3 sites confirming the answers.

Pass the exam yesterday 88x/1000…I got total of 60 Qs

3 Labs: EIGRP Stub, OSPF Virtual Link and OSPF-EIGRP Redistribution

Lots of new questions, DnD Qs, Frame Relay Qs

What’s up brethern? Lurker on the forum. Nailed the exam today with 900+ today. All in one + questions on forum (check pages 148 and forward) are enough for a pass. About 10-15 new questions about Vlans, DHCPv6, OSPF, AAA, NTP and I think there was a new question about NAT. Anyway, good luck to all of you. Study the book and watch videos too! That piece of paper is useless without knowledge!

Peace!

@doka

the question is not clear about what route that we talk about, if it’s route from neighbor, when point to point interface is down, route from neighbor will disappear immediately. what makes you believe it’s D (240s)?

@doka

if there is no new update about the route from neighbor for 240s (without interface down), i agree the answer is D. but the question talk about point to point interface down

I passed on friday all sims and DnD on digitalut are valid so just master them thoroughly be4 u take the exams . Copy run start its working in one simulator i forgot which one but after done configuration just try to save otherwise u may loose some marks . All the question come on this website and update from this forum so makesure u study them all

Which two types of threshold can you configure for tracking objects? (Choose Two)
A. percentage
B. MTU
C. bandwidth
D. weight
E. delay
F. administrative distance

Correct Answer: AD

Explanation:
Object Track List

An object track list allows you to track the combined states of multiple objects. Object track lists support the following capabilities:

Boolean “and” function—Each object defined within the track list must be in an up state so that the
track list object can become up.

Boolean “or” function—At least one object defined within the track list must be in an up state so
that the tracked object can become up.

Threshold percentage —The percentage of up objects in the tracked list must be greater than the
configured up threshold for the tracked list to be in the up state. If the percentage of down objects
in the tracked list is above the configured track list down threshold, the tracked list is marked as down.

Threshold weight —Assign a weight value to each object in the tracked list, and a weight threshold
for the track list. If the combined weights of all up objects exceeds the track list weight up threshold,
the track list is in an up state. If the combined weights of all the down objects exceeds the track list weight down threshold, the track list is in the down state.

https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5600/sw/unicast/7x/unicast_n5600_config/l3_object.html

just pass the exam with 9xx, there’s some question that i’ve never seen before, around 9 question. labs and Dnd are the same (eigrp stub, eigrp-ospf redistribution, ospf sim).

i’ll try to update later, thanks everyone.

@astalavista pls update new questions from your exam, tks!

Hi Guys,

Anyone who wrote recently advise if “All in One Kikavich” is valid enough for passing?

Thanks,
John_Snow “winter is coming”

@Route
yes, 135 n DnD kikavich and posted questions in this forum are enough to pass.

“?” , “tab” were working perfectly fine on my labs, so no problemo!

However, “copy runn-config start…” OR “write memory” were disable…..so you just have to skip to save the config. the labs are designed to self saved the configs.

Hi Guys,

Passed the Route Exam on Friday.
A lot of questions about NAT64, NPTV6, NAT-PT (stateless, statefull) if you clear about the differences then you will clear the questions.

SIM: Policy Based Routing, EIGRP OSPF Redistribution Ethernet One, IPv6 OSPF Virtual Link Sim.
Got some security questions about MPP and CoPP that never saw in the dumps.
A lot of questions from the Dump but make sure you know the concepts then you will be able to pass the exam.

Got luck all of you.

Hi Guys

Pass the exam just now , only one or two question was new . Kavick dump is enough as per my experience.

Hi,

Please give me your support.

I don’t find the crack for VCE yet.
Does digitaltut cover all questions in AllinOne Kavick dump?

dear all
any body shure that dumps are stable now
if yes then which dumps

@Ali Ahmed plz contact me
ahmed madiboi @ yahoo .com

Hi @faouji,

It seems “All in One Kikavich” is still enough to pass.
Check the keyword on page 160.

hi,

can someone explain me this DnD question about Tacacs+ and Radius ?

Radius support full features of accounting
Tacacs+ doesnt support full features accounting ?

is it possible ?

@Ali Ahmed plz contact me
ahmed madiboi @ yahoo .com

plllllllllllllllz help me my exam is sooon

Doublle post from earlier

DnD in below w. 477Q , Kikavich corrected

https:// drive . google.com/drive/folders/1UyTdhAq3k2qn-pOwZ41Bpv-FmA7rmKgu

Kikavich
https:// drive . google.com/drive/folders/1UyTdhAq3k2qn-pOwZ41Bpv-FmA7rmKgu
All in one
https:// www . dropbox.com/s/oqd7dept3tdg1vy/all%20in%20one.vce?dl=0
jazzy + prince
https:// drive . google.com/drive/folders/1zPsB1wW8QtA8ThFgI_qKBhSXr8reOJKx
https:// drive . google.com/drive/folders/1fKVLXnpMrjLgxMna8wkazos1YV09XzVZ