Share your ROUTE v2.0 Experience

Hi 195q is still legit.

DND gre tunnel / frame-relay multipoint

eigrp stub / ospf stub/mutual redistribution.

Any VCE files? Only seeing the PDF files.

24. Router DHCP is configured to lease IPv4 and IPv6 addresses to clients on ALS1 and ALS2. Clients on ALS2 receive IPv4 and IPv6 addresses. Clients on ALS1 receive IPv4 addresses.
Which configuration on DSW1 allows clients on ALS1 to receive IPv6 addresses?
A. DSW1l (config-if)# ipv6 helper address 2002:404:404::404:404
B. DSW1 (config)#ipv6 route 2002:404:404::404:404/128 FastEthernet 1/0
C. DSW1 (dhcp-config)# default-router 2002:A04:A01::A04:A01
D. DSW1 (config)# ipv6 dhcp relay destination 2002:404:404::404:404 GigabitEthernet 1/2

Answer: C

25. Which three benefits does the Cisco Easy Virtual Network provide to an enterprise network? (Choose three.)
A. simplified Layer 3 network virtualization
B. improved shared services support
C. enhanced management, troubleshooting, and usability
D. reduced configuration and deployment time for dot1q trunking
E. increased network performance and throughput
F. decreased BGP neighbor configurations

Answer: A, B, C or BCD from chat igor’.

26. Which three items can you track when you use two time stamps with IP SLAs? (Choose three.)
A. delay
B. jitter
C. packet loss
D. load
E. throughput
F. path

Answer: A, B, C

27. Which two commands do you need to implement on a router to support pppoe client ?
A. peer default ip address pool
B. mtu
C. bba-group pppoe
D. pppoe enable group
E. pppoe-client dialer-pool-number
Aswers: B and E

28. Which two statements about NHRP in a DMVPN environment are true? (Choose two)
a. It requires each endpoint to have a unique network ID
b. It routes traffic through the tunnel
c. It can identify PIM-SM RPs over a tunnel
d. It can authenticate VPN endpoints
e. It provides address resolution to route traffic

answer: D and E

29. In which scenario can asymmetric routing occur?
a. active/active firewall setup
b. single path in and out of the network
c. active/standby firewall setup
d. redundant routers running VRRP

answer: D ?

30. After reviewing the EVN configuration, a network administrator notices that a predefined EVN, which is known as “vnet global” was configured. What is the purpose of this EVN?
A. It defines the routing scope for each particular EVN edge interface.
B. It aggregates and carries all dot1q tagged traffic.
C. It refers to the global routing context and corresponds to the default RIB.
D. It safeguards the virtual network that is preconfigured to avoid mismatched routing instances
Answer: C

31. Which CLI command can you enter to permit or deny IPv6 traffic travelling through an interface?
A. access-list
B. access-group
C. ipv6 access-class
D. ipv6 traffic-filter
Answer: D

32. A network engineer executes the show ip cache flow command. Which two types of information are displayed in the report that is generated? (Choose 2)
A. top talkers
B. flow export statistics
C. flow sample for specific protocols
D. MLS flow traffic
E. IP packet distribution
Answer: CE

33. A network engineer needs to verify IP SLA operations on an interface that shows on indication of excessive traffic. Which command should the engineer use to complete this action?
a. show frequency
b. show track
c. show reachability
d. show threshold

34. Which option is the minimum logging level that displays a log message when an ACL drops an incoming packet?
a. level 3
b. level 6
c. level 7
d. level 5

answer: b

34. Other than a working EIGRP configuration, which option must be the same on all routers for EIGRP authentication key role over to work correctly?
A. SMTP
B. SNMP
C. Passwords
D. Time
Answer: C

What page is the 195q on? I’m only finding the one with 700+q. Also, does it have the VCE file and not just the PDF?

Found the 195. Page 217. Second file from left. September ver. 2.1

https://drive.google.com/drive/folders/1Cf4MHTm8Qt5-_jYzJt6PXNy6b6YOBEx1

Found it on page 217. Second from the left.

Remove spaces
https:// drive.google.com/drive /folders/ 1Cf4MHTm8Qt5-_jYzJt6PXNy6b6YOBEx1

If 195q is still legit why do these people keep posting questions from older exams?

@@@confirm?

You can tell people the sky is blue and the still will ask the color of the sky. :)

195q still valid ?

09.28.2018 195q dump is still valid ? Please help

friends pass the exam with 92x punctuation networking 100% valid and the laboratories are the same of this page.
thanks networking, see you in ccnp switch

Where do I find the 195q? Is it on this site?

@HELP,
search in the previous pages for a post for the guy named nnnnneeeettttwwwoooorrrrkkkkiiiinnnng and you will find a shared link, through it you can download the 195q

24. Router DHCP is configured to lease IPv4 and IPv6 addresses to clients on ALS1 and ALS2. Clients on ALS2 receive IPv4 and IPv6 addresses. Clients on ALS1 receive IPv4 addresses.
Which configuration on DSW1 allows clients on ALS1 to receive IPv6 addresses?
A. DSW1l (config-if)# ipv6 helper address 2002:404:404::404:404
B. DSW1 (config)#ipv6 route 2002:404:404::404:404/128 FastEthernet 1/0
C. DSW1 (dhcp-config)# default-router 2002:A04:A01::A04:A01
D. DSW1 (config)# ipv6 dhcp relay destination 2002:404:404::404:404 GigabitEthernet 1/2

Answer: C

25. Which three benefits does the Cisco Easy Virtual Network provide to an enterprise network? (Choose three.)..
A. simplified Layer 3 network virtualization
B. improved shared services support
C. enhanced management, troubleshooting, and usability
D. reduced configuration and deployment time for dot1q trunking
E. increased network performance and throughput
F. decreased BGP neighbor configurations

Answer: A, B, C or BCD from chat igor’.

26. Which three items can you track when you use two time stamps with IP SLAs? (Choose three.)
A. delay
B. jitter
C. packet loss
D. load
E. throughput
F. path

Answer: A, B, C

27. Which two commands do you need to implement on a router to support pppoe client ?
A. peer default ip address pool
B. mtu
C. bba-group pppoe
D. pppoe enable group
E. pppoe-client dialer-pool-number
Aswers: B and E

28. Which two statements about NHRP in a DMVPN environment are true? (Choose two)..
a. It requires each endpoint to have a unique network ID
b. It routes traffic through the tunnel
c. It can identify PIM-SM RPs over a tunnel
d. It can authenticate VPN endpoints
e. It provides address resolution to route traffic

answer: D and E

29. In which scenario can asymmetric routing occur?
a. active/active firewall setup
b. single path in and out of the network
c. active/standby firewall setup
d. redundant routers running VRRP

answer: D ?

30. After reviewing the EVN configuration, a network administrator notices that a predefined EVN, which is known as “vnet global” was configured. What is the purpose of this EVN?
A. It defines the routing scope for each particular EVN edge interface.
B. It aggregates a.nd carries all dot1q tagged traffic.
C. It refers to the global routing context and corresponds to the default RIB.
D. It safeguards the virtual network that is preconfigured to avoid mismatched routing instances
Answer: C

31. Which CLI command can you enter to permit or deny IPv6 traffic travelling through an interface?
A. access-list
B. access-group
C. ipv6 access-class
D. ipv6 traffic-filter
Answer: D.

32. A network engineer executes the show ip cache flow command. Which two types of information are displayed in the report that is generated? (Choose 2)
A. top talkers
B. flow export statistics
C. flow sample for specific protocols
D. MLS flow traffic
E. IP packet distribution
Answer: CE

33. A network engineer needs to verify IP SLA operations on an interface that shows on indication of excessive traffic. Which command should the engineer use to complete this action?
a. show frequency.
b. show track
c. show reachability
d. show threshold

34. Which option is the minimum logging level that displays a log message when an ACL drops an incoming packet?
a. level 3
b. level 6
c. level 7
d. level 5

answer: b

34. Other than a working EIGRP configuration, which option must be the same on all routers for EIGRP authentication key role over to work correctly?
A. SMTP
B. SNMP
C. Passwords
D. Time
Answer: C

hi to all, i’m the only one that see in 195 nnneeettwooorking that the Drag & Drop of scrict and loose mode have the same object? Loose mode and loose mode :)

q698

@nneettwwoorrkkiinngg

can you share the VCE password, i want to correct the DnD q698

@funghet no mate you’re not alone. There are loads of wrong answers too which kept confusing me, i tried to correct them but need a password which i don’t have.

@Googleplex

can you write the n° of the question that you think is wrong ? so i can check it :)

These are the questions which are repeated several times & everytime they have different answers, if you can help, it would be much appreciated. I did my own research so i’ll choose those answer in my exam but lets double check ahaha.

Which two causes of latency are true? (Choose two)
A. High bandwidth on a link
B. Split horizon
C. Propagation delay
D. Serialization delay
E. Under-utilizaion of a link

Which two statements about the enable secret and enable password commands are true? (Choose two)
A. I both commands are missing from the global configuration,vtp lines use the console password
B. The enable secret command overrides enable password
C. The enable password command has a stronger encryption algorithm than enable secret
D. The enable secret commmand is bac kwards-compatible with more version of IOS
E. The enable secret and enable password commands must be used togerher

How big is the smallest packet than will always be fragmented on a standart Ethernet network with default configuration?
A. 1500 bytes
B. 1800 bytes
C. 2048 bytes
D. 2100 bytes

Which two statements are true about EVN? (Choose Two)
A. A configuration can be based on an existing VRF configuration
B. It supports IPv6 traffic
C. It can support up to 16 VNs
D. It uses redistribution to share routers between VNs
E. It supports SSM only

In which state do DR and BDR establish adjacency with each ospf router in the network

A. Exstart State
B. Loading State
C. Exchange State
D. Init State

Which criterion does the BGP maximum path feature use for load balancing?.

A. Router ID
B. MED
C. Weight
D. Local Pref

which protocol use both best path and second best path for traffic??
A. EIGRP
B.OSPF
C.BGP
D.RIP

If this configuration is applied to a device that redistributes EIGRP routes into OSPF. which two statements about the behavior of the device are true? (Choose Two )
A. EIGRP routes appears in the routing table as E2 OSPF routes
B. The device router ID is set to Loopback0 automatically
C. The device redistributes all EIGRP networks into OSPF
D. EIGRP routes appears in the routing table as N2 OSPF routes
E. The device redistributes only classful EIGRP networks into OSPF
F. EIGRP routes appears as type 3 LSAs in the OSPF database

What happends when unicast flood protection is triggered on a VLAN?
A. The VLAN is shut down
B. Traffic on the VLAN is load-balanced across multiple links
C. The VLAN is removed from the VLAN database
D. Traffic on the VLAN is passed to another VLAN with lower load

In which two areas does OSPF send a summary route by default ?
A. NSSA
B. Backbone
C. Totally stubby
D. Stub
E. Normal

I tried various audio lectures & video lectures for the preparation of 30-101 exam but that all was in vain. Then I got 300-101 PDF from braindumpscerts.com by learning their study material I passed the 300-15 exam very easily. The biggest benefit is 100 % success rate. had a great experience. Highly recommended.

some more questions.

If you configure one router in your network with the auto-cost reference-bandwidth 100 command, which effect on the data path is true?
A. The data path remains the same for all links
B. The data path changes for 10Mbps links only
C. The data path changes for all links
D. The data path changes for 10Gbps links only

which adverse circumstance can the ttl feature prevent?
A. DoS attack
B. CAM table overload
C. Link saturation
D. routing loops

where you enable RIPng?
A. Interface config
B. Router sub command
C. Router config
D. Global config

Hi all, please share the last valid dumb and the VCE

I notice everyone is saying mtu, take a look at this video of keith bogart, based on the config
it would be C and D

Which two commands do you need to implement on a router to support pppoe client ?
A. peer default ip address pool
B. mtu
C. bba-group pppoe
D. pppoe enable group
E. pppoe-client dialer-pool-number

Exam passed today (8XX/1000)
195q is still valid, no new questions

@GIGI
thanks for the confirmation.

@GIGI which labs did you get? were they similar & glitch free or not?

please share 195q dump

Please, share Nneettwwoorrkkiinngg dump

Nneettwwoorrkkiinngg dump 753q , which is 195q ??????

@Andy – Thanks a bunch!

@Annoy
there should be a file in the VCE that says September.

The enterprise network WAN link has been receiving several denial of service attacks from both IPv4 and IPv6 sources. Which three elements can you use to identify an IPv6 packet via its header, in order to filter future attacks? (Choose three)
A. Traffic Class
B. Source address
C. Flow Label
D. Hop Limit
E. Destination Address
F. Fragment Offset

HElp

Guys whoever is posting different-different qus please don’t trust them. Nneettwwoorrkkiinngg 195q are valid and all ans also correct.

Today i passed CCNP Route exam with score 9xx/1000.

Thanks Nneettwwoorrkkiinngg and digitaltut.

Lab sim:- Eigrp Stub, EIGRP n OSPF redistribution sim and OSPF sim. My friend got Eigrp Stub, EIGRP n OSPF redistribution sim and IPv6 OSPF virtual sim.

DD:-uRPF ,Frame Relay LMI , GRE feature and ACL

See you on switching side.

Kindly go back few pages back and you will find real Nneettwwoorrkkiinngg without paid.
I guess this information is enough to help you guys.

@AR congrats. My exam is next week but i have a question, pls answer if you can. Did you encounter any problem on labs especially on IPV6 Sim? Using all the commands from 9tut were you able to ping R4 from R1 or did you configure loopback on R1? Pls answer, anyone else who has recently passed the exam, cheers guys xxx :)

Can someone help me out with this question?

Which statement about stateless and stateful IPV6 configuration are true
A. Both stateless and stateful configuration require no additional setup
B. Stateles requires no additional setup, sateteful does require
C. Stateless requires additional setup, sateful doesn’t require
D. Both require no additional setup
Answer: B, but saw A in some places

Do they mean no configuration client-side or server-side?

Also, this Frame Relay question:

Which two statements about configuring Frame Relay point-to-multipoint connections are true? (Choose two)
A. They ignore the broadcast keyword in the frame-relay DLCI mapping.
B. They require the same DLCI on each side of the link.
C. Changing a point-to-multipoint subinterface to a different type requires the interface to be deleted and recreated.
D. They require the frame-relay mapping command to be configured.
E. They require inverse ARP.
Answer: D, E

@Zitto

you see this questions in your exam, those are news

8. What from the following can cause an issue for URPF? (this could be single answer or multiple choice)
URPF
FAIL
Reasons why urpf may fail:
A.Assymetric routing
B.Cef not enabled
C.Urpf not applied to the traffic source
D.If it is used as ingress filtering
ans:a

11. Configuration snippet that looks similar to this:
ip access-list 1 permit xx xx
ip nat inside source list 1 int fa0/0 overload
What is this an example of ?

A. static NAT
B. NAT64
C. PAT
D. dynamic NAT
E. NPTv6
Answere: C

12. Which two routers can do OSPF route summarization. (Choose Two)

A. ABR
B. ASBR
C. Summary router
D. internal router
E. Backbone router
Answere: A & B

2) what is supported radius server (choose two)

A) telnet
B) authentication
C) accounting
D) authorization
E) SSH
Answare:BD

My exam is next week but i have a question, pls answer if you can. Did any of you encounter any problem on labs especially on IPV6 Sim? Using all the commands from 9tut were you able to ping R4 from R1 or did you configure loopback on R1? Pls answer, anyone who has recently passed the exam, cheers guys xxx :)

Dear All,
Just passed exam today with 9xx score.
networking 195q is 100% valid,
thanks to networking and all other friends who put their efforts to make this happen.
God bless you all.

passed the exam with 9xx yesterday All the question are from 195q and lab are from digitul premium. I think I got 9xx because some answer in 195 is not correct.. but guys dont worrry, just use 195q and you should be all good.

I got 3 lab…eigrp redist, ipv6 and eigrp stub
D and D : COPP/MPP, framerelay and couple of more

I would like to thank networkinggggg for all his help.

At last, want to show middle finger to one of the spammer here who post same thing with whatssup link changing his name now and then. I dont know what he gets doing it. he seems to have posted just now using LALA… TO FUNNY and such a poor guy who has time to do this everyday.

God bless cisco!!
Aaameen!

@sha-2048 congrats on passing your exam :) but can you pls answer my question if you can, i really need to know. Everyone is spamming but no one is answering :(

@sha-2048 CONGRATS!!! can you share your updated materials ?? Thanks so much. Big Help

Hello Guys,

Can I ask the 195 questions everyone is talking about. I have checked the networkinggggg last PDF which has over 700 questions. which part can be found the 195 questions?

Thanks

@Sasha thanks.

I didn’t face any issue in lab sim. I was able to ping Loopback on R1 was pre-reconfigured. The only thing which i faced is, write command was not taking.

Thanks

@Haji,
In that same 700 qx pdf file, you will find one section named “valid-September “ having 195qx

QUESTION 8
Which address is used by the Unicast Reverse Path Forwarding protocol to validate a packet against the
routing table?
A. source address
B. destination address
C. router interface
D. default gateway
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
Explanation/Reference:
Explanation:
The Unicast RPF feature helps to mitigate problems that are caused by the introduction of malformed or forged
(spoofed) IP source addresses into a network by discarding IP packets that lack a verifiable IP source address.
For example, a number of common types of denial-of-service (DoS) attacks, including Smurf and Tribal Flood
Network (TFN), can take advantage of forged or rapidly changing source IP addresses to allow attackers to
thwart efforts to locate or filter the attacks. For Internet service providers (ISPs) that provide public access,
Unicast RPF deflects such attacks by forwarding only packets that have source addresses that are valid and
consistent with the IP routing table. This action protects the network of the ISP, its customer, and the rest of
the Internet.
http://www.cisco.com/en/US/docs/ios/12_2/security/configuration/guide/scfrpf.html
QUESTION 9
What are the three modes of Unicast Reverse Path Forwarding?
A. strict mode, loose mode, and VRF mode
B. strict mode, loose mode, and broadcast mode
C. strict mode, broadcast mode, and VRF mode
D. broadcast mode, loose mode, and VRF mode
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
Explanation/Reference:
Explanation:
Network administrators can use Unicast Reverse Path Forwarding (Unicast RPF) to help limit the malicious
traffic on an enterprise network. This security feature works by enabling a router to verify the reachability of the
source address in packets being forwarded. This capability can limit the appearance of spoofed addresses on
a network. If the source IP address is not valid, the packet is discarded. Unicast RPF works in one of three
different modes: strict mode, loose mode, or VRF mode. Note that not all network devices support all three
modes of operation. Unicast RPF in VRF mode will not be covered in this document. When administrators use
Unicast RPF in strict mode, the packet must be received on the interface that the router would use to forward
the return packet. Unicast RPF configured in strict mode may drop legitimate traffic that is received on an
interface that was not the router’s choice for sending return traffic. Dropping this legitimate traffic could occur
when asymmetric routing paths are present in the network. When administrators use Unicast RPF in loose
mode, the source address must appear in the routing table. Administrators can change this behavior using the
allow-default option, which allows the use of the default route in the source verification process. Additionally, a
packet that contains a source address for which the return route points to the Null 0 interface will be dropped.
An access list may also be specified that permits or denies certain source addresses in Unicast RPF loose
mode.
Care must be taken to ensure that the appropriate Unicast RPF mode (loose or strict) is configured during the
deployment of this feature because it can drop legitimate traffic. Although asymmetric traffic flows may be of
concern when deploying this feature, Unicast RPF loose mode is a scalable option for networks that contain
asymmetric routing paths.
http://www.cisco.com/web/about/security/intelligence/unicast-rpf.html

QUESTION 8
Which address is used by the Unicast Reverse Path Forwarding protocol to validate a packet against the
routing table?
A. source address
B. destination address
C. router interface
D. default gateway
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
Explanation/Reference:
Explanation:
The Unicast RPF feature helps to mitigate problems that are caused by the introduction of malformed or forged
(spoofed) IP source addresses into a network by discarding IP packets that lack a verifiable IP source address.
For example, a number of common types of denial-of-service (DoS) attacks, including Smurf and Tribal Flood
Network (TFN), can take advantage of forged or rapidly changing source IP addresses to allow attackers to
thwart efforts to locate or filter the attacks. For Internet service providers (ISPs) that provide public access,
Unicast RPF deflects such attacks by forwarding only packets that have source addresses that are valid and
consistent with the IP routing table. This action protects the network of the ISP, its customer, and the rest of
the Internet.
http://www.cisco.com/en/US/docs/ios/12_2/security/configuration/guide/scfrpf.html
QUESTION 9
What are the three modes of Unicast Reverse Path Forwarding?
A. strict mode, loose mode, and VRF mode
B. strict mode, loose mode, and broadcast mode
C. strict mode, broadcast mode, and VRF mode
D. broadcast mode, loose mode, and VRF mode
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
Explanation/Reference:
Explanation:
Network administrators can use Unicast Reverse Path Forwarding (Unicast RPF) to help limit the malicious
traffic on an enterprise network. This security feature works by enabling a router to verify the reachability of the
source address in packets being forwarded. This capability can limit the appearance of spoofed addresses on
a network. If the source IP address is not valid, the packet is discarded. Unicast RPF works in one of three
different modes: strict mode, loose mode, or VRF mode. Note that not all network devices support all three
modes of operation. Unicast RPF in VRF mode will not be covered in this document. When administrators use
Unicast RPF in strict mode, the packet must be received on the interface that the router would use to forward
the return packet. Unicast RPF configured in strict mode may drop legitimate traffic that is received on an
interface that was not the router’s choice for sending return traffic. Dropping this legitimate traffic could occur
when asymmetric routing paths are present in the network. When administrators use Unicast RPF in loose
mode, the afdsource address must appear in the routing table. Administrators can change this behavior using the
allow-default option, which allows the use of the defaulefwt route in the source verification process. Additionally, a
packet that contains a source address for which the return route points to the Null 0 interface will be dropped.
An access list may also be specified that permits or denies certain source addresses in Unicast RPF loose
mode.
Care must be taken to ensure that the appropriate Unicast RPF mode (loose or strict) is configured during the
deployment of this feature because it can drop legitimate traffic. Although asymmetric traffic flows may be of
concern when deplascoying this feature, Unicast RPF loose mode is a scalable option for networks that contain
asymmetric routing paths.
http://www.cisco.com/web/about/security/intelligence/unicast-rpf.html

h ttp :
//j.mp/2Pxd7Ht

The latest question bank, the most complete information, or the teacher of online guidance.

QUESTION 82
Which common issue causes intermittent DMVPN tunnel flaps?
A. a routing neighbor reachability issue
B. a suboptimal routing table
C. interface bandwidth congestion
D. that the GRE tunnel to hub router is not encrypted
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
Explanation/Reference:
Explanation:
DMVPN Tunnel Flaps Intermittently
Problem
DMVPN tunnel flaps intermittently.
Solution
When DMVPN tunnels flap, check the neighborship between the routers as issues with neighborship formation
between routers may cause the DMVPN tunnel to flap. In order to resolve this problem, make sure the
neighborship between the routers is always up.
http://www.cisco.com/c/en/us/support/docs/security-vpn/ipsec-negotiation-ike-protocols/29240-
dcmvpn.html#Prblm1
QUESTION 83
What is the purpose of configuring the router as a PPPoE client? Select the best response.
A. to provide VPN access over L2TP
B. to enable PPP session from the router to the termination device at the headend for metro Ethernet
connectivity
C. for DSL connectivity and removing the need for the end-user PC to run the PPPoE client software
D. for connecting the router to a cable modem, which bridges the Ethernet frames from the router to the cable
modem termination system
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
Explanation/Reference:
QUESTION 84
Which three are characteristics of IPv6? (Choose three.) Select 3 response(s).
A. An IPv6 address is 128 bits long.
B. An IPv6 header is 20 bits long.
C. An IPv6 header contains the next header field.
D. An IPv6 header contains the protocol field.
E. IPv6 routers send RA messages.
F. An IPv6 header contains the header checksum field.
Correct Answer: ACE
Section: (none)
Explanation
Explanation/Reference:
Explanation/Reference:
QUESTION 85
When an IPv6 enabled host boots, it sends a router solicitation (RS) message. An IPv6 router responds with a
router advertisement (RA). Which two items are contained in the RA? (Choose two.) Select 2 response(s).
A. IPv6 address for the host
B. lifetime of the prefix
C. prefixes for the link
D. keepalive timers
E. request for the local host IP address
F. any route advertisements it has received
Correct Answer: BC
Section: (none)
Explanation
Explanation/Reference:
Explanation/Reference:
QUESTION 86
Which statement is true about IPv6? Select the best response.
A. Only one IPv6 address is assigned per node.
B. Only one IPv6 address can be assigned to each interface.
C. Each host can autoconfigure its address without the aid of a DHCP server.
D. IPv6 hosts use anycast addresses to assign IP addresses to interfaces.
Correct Answer: C

Hello,

Someone are able to confirm that only these 195 Questions are enough to the passed exam?