Share your ROUTE v2.0 Experience

Hi all.
I pass today with 8xx scores. File Jule_2019 is enough.
Lab: OSPF eva, PBR with link is fast, EIGRP-OSPF Redistribution. 6 or 7 D&D, but all are in file Jule_2019.
Thanks Digitaltut.

Hi all.

I fail today 78x scores.
Lab: OSPF eva, PBR with link is fast, EIGRP-OSPF Redistribution case 2

remark:OSPF Evaluation simulator is changed a bit. R2-R3 timer is changed so this is not correct answer any more. R2-R3 is point-to-point and R1-R3 is point-to multipoint non broadcast. Questions with timer are incorrect now so my answer was that R1-R3 link need neighbor command for adjacency

D&D:
1.
Excessive unicast flooding condition: caused by including a host port in STP
Out-of-order packets: potential result of disabling FIFO
TCP starvation: potential effect of excessive UDP traffic on link
Asymmetric routing: cause of inconsistent traffic patterns
Latency: condition in which packets require an excessive length of time to traverse a switch

2.
+ if authenticated – It allows the user to perform the requested function once authenticated
+ none – It instructs the network access server to proceed without requesting authorization information
+ local – It provides authorization for a limited set of functions only
+ krb5-instance – It uses a defined instance for authorization
+ group radius – It uses authorization information from a standards based server
+ group tacas+ – It uses authorization information stored as attribute value pair in a Cisco proprietary server

3.
+ Authentication: challenge and response operation
+ Accounting: feature that logs network usage
+ TACACS+: authentication method that uses TCP
+ RADIUS: authentication method that uses UDP
+ Authorization: controls specific access privileges of a user

Good luck..

Hi Justdoit. What about single & multiple choice questions. Were they all from MPQ, NUQ5 & NUQ6?

I am very happy I have pass my exam yesterday with score 9XX. I would like to give a special thanks to DTUT premium and all of you peoples that have help me with your comments and tips for this exam.
I have practice from the flash-based simulators in DTUT premium and used the JULY dumb.

Lab: OSPF sim, PBR, EIGRP-OSPF Redistribution.
I think like 2 new questions and 2 new DD about AAA.

glad to hear you passed! :)

do you remember the 2 q’s and the DD’s?

Hi All,

Planning for CCNP route exam. Kindly share latest dumps, if anyone have it.
Appreciate your help.

dbrahma224*gmail.com

pass today with 888…

Lab Policy (the same), redistribution (fast link between R3-R4), OSPF Sims (q2 change: R1 has area 0 inactive, the timers were ok).

DnD: aaa commands, Nat64 vs NTP, Radius vs Tacacs+, AAA, Frame relay (LMI, PCV, etc;).

Some questions of IP SLA.

Question of BGP about the mismatch causes of MTU.
Some of frame Ralay in EIGRP and OSPF change point-to-multipont
Questions about VRL-lite.
Questions about IPv6 were a lot of the test.
A few new questions (VRF) that ain’t in the document.
Finallly, the same questions of EIGRP and OSPF.

@What! July Dump is still valid?

Or what dump do you have taked?

Congrats for you!!!

Guys anyone who tells his charming success story and ends up recommending some premium crap is Fake. don’t fall for this kind of baits.
Anyone who had just passed with a valid dumb would be happy to share his version of that dump.
in case you wanna help me by sharing any valids “And I will pay it forward”: incase505*@mail.com without “*”

I passed today with 86x points. Thx for the help :)

Labs are still PBR, OSPF/EIGRP Redist, OSPF eval.

They changed the OSPF eval question no. 2 – because the r2/r3 link is no longer 30/120/120 in timers, instead the link between r1/r3 I think is inactive(seen from r1 -sh ip ospf) because r1 needs neighbor statement (i think).

some questions about:

VRF-lite
IP SLA
NAT64
Network time protocol
PPPoE, PPP and Frame relay
AAA (tacacs/radius differences, AAA commands etc)
DMVPN (hub, spokes, ipsec, subinterfaces, NBMA, mGRE)
Cisco EVN
OSPF LSA types

Dumps are still valid, but never a bad idea to actually study some of the topics ;)

@watch out fakes check your mail ;)

thanks !

what else about the ospf sim is different ?

any thing different with the pbr and ospf/eigrp sims? or are the same as on here?

CJ

Hi guys anybody has the VCE file for july 2019 pdf ccnp routing. thank you.appreciate if u can send me the vce file.PINOY here. :)

Pass today with 9** score. Dumps are still valid. Make sure to study well also. PBR, eigrp- ospf distrib and ospf evaluation.

Passed 06 August 2019, almost questions from Digitaltut, nothings new. 925/1000.
Lab : OSPF Redistribute, Policybase Routing.

PLEASE SHARE JULY 2019 DUMP ({email not allowed})

PLEASE SHARE JULY 2019 DUMP (dignes7 alt hotmail dot fr)

MingMing Aba , please can you send me your dump please (dignes7 alt yahoo dot fr)

Meoxam2007, (please can you send me your dump please (dignes7 alt yahoo dot fr)

Passed Yesterday with 87X, about 80% from July Dump, some new questions not seen before – you should be ok with just July. Labs PBR, OSPF – EIGRP Redistribute, OSPF Eval – Q2 has changed, timers 30 120 120 no int R3-R2, Went with Neighbor command to bring up adjanency. D+D MGre, Frame Relay. It can be done

Hi guys,

Anyone with the latest dumps of 210-060 CICD.

arayam506 @ gmail com

Hi everyone,

I am about to take this exam in next couple of days, but I noticed that some guys had a problem with PBR LAB?

Can you please help me with this:

– How do you get next-hop ip address? Is it written on the diagram or we have to use some show commands?

— Do we need to implement configuration from this website or the one that guy provided in last comment?

This is configuration from this site:

BorderRouter(config)#route-map pbr permit 10
BorderRouter(config-route-map)#match ip address 101
BorderRouter(config-route-map)#set ip next-hop 10.1.101.1

This is the one that he provided in the comment:
route-map pbr permit 10
match ip address 101
set ip next-hop 10.1.101.1
set ip next-hop verify-availability

The last question is, how to do you provide this type of traffic once you are on the exam? Do you ping or how? Which command do we need to use?

Thanks in advance.

redwhiteblue

By default, what is the number of paths that are used for load-sharing by BGP?
A) 1
B) 2
C) 4
D) 6
Answer: A
By default, Border Gateway Protocol (BGP) selects only a single best path and does not perform load balancing.
https://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/13762-40.html

By default what is the maximum number of equal metric path BGP uses for load balancing?
A. 6
B. 4
C. 8
D. 16
Answer: A (I guess)
Four entries is the default in IOS for most IP routing protocols with the exception of Border Gateway Protocol (BGP), where one entry is the default. Six different paths configured is the maximum number.
https://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/5212-46.html

Hello, How much do I pay for the premium?

Hi guys, I need ios with ipv6 address family for route i need to do some lab with EIGRP

Question 3
Refer to the following command:
router(config)# ip http secure-port 4433
Which statement is true?
A. Thde router will listen on port 4433 for HTTPS traffic.
B. The router will listen on port 4433 for HTTP traffic.
C. The router willwda never accept any HTTP and HTTPS traffic.
D. The router will listen to HTTP and HTTP traffic on port 4433.
Ans given is A I think its B
Please guide me

@Anonymous
The answer is A.
http secure-port means HTTPS, without “secure-port” it’s just http.

Hey Guys

Did any of you use the premium VCE from examcollection?
And is it valid?
i went throught the first 20 questions on the July dump from this site and none of them appear on the examcollection VCE..Please advise?

Hello Everyone, Passes my Exam today with 948/100.

Labs: OSPF Eval, PBR and EIGRP-OSPF Redistribution

DnD: Frame Relay, AAA, NAT64, GRE

There were a few questions I have study from that dumps So make sure you study the MPQ, NUQ5, NUQ6

Without 1 star**
https:/*/zkrt.cz/F0i

Does anybody know the answer to these two questions? I am confused because there seems to be a contradiction.

By default what is the maximum number of equal metric path BGP uses for load balancing?
A. 6
B. 4
C. 8
D. 16

By default, what is the number of paths that are used for load-sharing by BGP????????????
A) 1
B) 2
C) 4
D) 6

I am so happy I passed this exam last week! I was surprised to see my score at exactly 7**!
I tried to review for this exam just for a week (1day review on the labs before the exam date) and no practice on the laboratory (just rewriting the configurations which seems gave me a hard time during the actual test).

I got 2 LABs: OSPF-EIGRP redistribution – I cannot ping from R1 to the Loopback destination of R4 but I can see the routes from R4 via fastethernet port from R3.
I put the redistribution commands inside “ospf 1” rather than the sample lab which states “router ospf 24 and 34” as it doesn’t appear on the current config after configuration.

and PBR (looks to be ok, I think!)

All are from July dumps (just backread guys on the link), just got confused due to a lot of questions in my mind. I have many drag and drops: AAA/ICMP/Frame Relay/NAT64.

Goodluck guys! and thanks again for this community! Always very helpful…
Took TSHOOT today and passed it with 4days of preparation. :)

wow congrats on both!

how did you find tshoot? you passed after 4 days of studying?

did you use networktut for that as well?

any thing else you remember from t shoot?

Maximum paths is 16, the default is 1. In other words you have to turn it on with the maximum paths command under the BGP process.

Which task must you perform to enable a point-to-point Frame Relay connection?

A. Enable inverse ARP.
B. Configure the encapsulation type.
C. Configure static address mapping.
D. Disable inverse ARP.

Ans is B o C ?

@EMPOY Pinoy ka?

please click on the link below to download the updated vce for August
https://*1drv.ms/u/s!*Atxexn_OaNVKjnWop_Q*8Lhm4zlQT?e=1ifM3Z

please remove the asterisk
Good luck in your route Exam.

Nick81

Thank´s so far.
Can´t open it with my Version of VCE, do you have a link to a VCE Player where i can open it
without Virus??

Passed today with 8xx.
Labs are PBR-Redistribution-OSPF eval.
All questions came from July Dumps.

Thanks DigitalTut!

Nick81 IS FAKE FAKE FAKE SPAMM………

Nick81 IS FAKE FAKE FAKE SPAMM…….

Nick81 IS FAKE FAKE FAKE SPAMM…….

There is a working VCE, however I don’t know if it is valid. Didn’t compare it with June from this site yet.

Yea… I passed 300-101 today with 85*
Thanks for your comments guys.. July dumps is still valid..

To those who think the vce I shared is fake down used it.
To those who are serious in passing their exam, you can download it.
Did I asked money from anyone.
Stop discouraging others who want to prepare for their route exam.
I am lecturer and will not waste my time giving out fake material.
What I am using to prepare my students for the exam is what I have posted here.
If you think it is spam or I am fake please don’t download.
Below is a link to download the pdf version of the file
https://1drv.ms/b/s!Atxexn_OaNVKjnfHEiXGPV4l3sb6?e=rRmZeE

The vce is the Chinese vce and it was updated on the 08-08-2019
please don’t focus on negative comments from other people.

Nick81 link is okey and it is the Chinese PDF file that come in 8-8-2019 .
Thank u Nick81 .

how to open the vce file?

what did you get in your exam?

you need a vce player to be able to open the vce

remark:OSPF Evaluation simulator is changed a bit. R2-R3 timer is changed so this is not correct answer any more. R2-R3 is point-to-point and R1-R3 is point-to multipoint non broadcast. Questions with timer are incorrect now so my answer was that R1-R3 link need neighbor command for adjacency

D&D:
1.
Excessive unicast flooding condition: caused by including a host port in STP
Out-of-order packets: potential result of disabling FIFO
TCP starvation: potential effect of excessive UDP traffic on link
Asymmetric routing: cause of inconsistent traffic patterns
Latency: condition in which packets require an excessive length of time to traverse a switch

2.
+ if authenticated – It allows the user to perform the requested function once authenticated
+ none – It instructs the network access server to proceed without requesting authorization information
+ local – It provides authorization for a limited set of functions only
+ krb5-instance – It uses a defined instance for authorization
+ group radius – It uses authorization information from a standards based server
+ group tacas+ – It uses authorization information stored as attribute value pair in a Cisco proprietary server

3.
+ Authentication: challenge and response operation
+ Accounting: feature that logs network usage
+ TACACS+: authenticationD method that uses TCP
+ RADIUS: authentication method that uses UDP
+ Authorization: controls specific access privileges of a user

Hello Everyone, Passes my Exam today with 948/100.

– SNMP inform v/s trap
– Types of uRPF
– ip nat tcp [ip adddress] 8080 [ip address] 80, what happen in that command? how NAT translate that?
– Lots of IP SLA Questions.
– Same lab
– New DD about AAA but it almost the same
– Like two new EVN questions
– SNMP new questions about how works

Without 1 star**
https:/*/zkrt.cz/F0i

Which task must you perform to enable a point-to-point Frame Relay connection?

A. Enable inverse ARP.
B. Configure the encapsulation type.
C. Configure static address mapping.
D. Disable inverse ARP.

Ans is B o C ?

Can someone please share the latest dump for CCNP route?

email me frotan.kadze @ gmail.com

Thank you,

Frotan