Share your ROUTE v2.0 Experience

I took exam today and get 72x. The exam questions was very easy almost all of the questions comes from the July Dump, but I have faced the copy run start command didn’t work on the routers.

Exam Content

3 Simulation

EIGRP/OSPF REDISTRIBUTION
PBR
OSPF EVALUATION – there is a change in the setup for 1 question which have 30,120,120 timer

7 or 8 D&D

interface Ethernet0
ip address 10.1.1.2 255.255.255.0
interface Serial0
! Serial interface config
no ip address
encapsulation frame-relay frame-relay
lmi-type ansi
! subinterface config interface
Serial0.1 multipoint
ip address 192.168.1.5 255.255.255.240
frame-relay map ip 192.168.1.1 100 broadcast

Authentication: challenge and response operation
Accounting: feature that logs network usage
TACACS+: authentication method that uses TCP
RADIUS: authentication method that uses UDP
Authorization: controls specific access privileges of a user

Loose Modes:
It supports using the default route as a route reference
It requires the source address to be routable
Strict Modes:
It can drop legitimate traffic
It permits only packets that are received on the same interface as the exit interface for the destination address

network-specific stateful NAT64 prefix: IPv6 prefix assigned by an organization
NAT64 : supports application layer gateway
NPTv6 : translates 2001:1::/64 to 2001:2::/64
well-known stateful NAT64 prefix: supports IPv6 prefix 64:FF9B::/96

NAT64:
Use Network-specific prefix
Modify session during translation
NPTv6:
Modify IP header in transit
Map one IPv6 address prefix to another IPv6 prefix

SVC: A circuit that provides temporary on-demand connections between DTEs
LMI: A signaling mechanism for Frame Relay devices
DLCI: A locally significant ID
FECN: An indicator of congestion on the network
PVC: A logical connection comprising two endpoints and a CIR

Authentication:
supports a local database for device access
supports encryption
Authorization:
specifies a user‘s specific access privileges
enforces time periods during which a user can access the device
Accounting:
not supported with local AAA
verifies network usage

Some that I remember.

First Question

Which Cisco VPN technology can use multipoint tunnel, resulting in a single GRE tunnel interface on the hub, to support multiple connections from multiple spoke devices?
A. DMVPN
B. GETVPN
C. Cisco Easy VPN
D. FlexVPN

Answer: A

Which is the minimum privilege level to allow a user to execute all user-level commands but prohibits enable-level commands by default?
A. level 1
B. level 0
C. level 16
D. level 15
E. level 14
Answer: A

Which value does a point-to-point GRE tunnel use to identify a peer?
A. MAC address
B. configured multicast address
C. DLCI
D. IP address
E. VC ID
Answer: D

Refer to the exhibit.
You notice that traffic from R1 to the 192.168.10 0/24 network prefers the path through R3 instead of the least-cost path through R2.What is the most likely reason for this route selection?
A. OSPF prefers external routes over interarea routes.
B. OSPF prefers interarea routes over intra-area routes.
C. OSPF prefers external routes over intra-area routes.
D. OSPF prefers intra-area routes over interarea routes.
Answer: D

Which command can be entered on router R5 to configure 80 percent of the bandwidth of a link for EIGRP Autonomous System 55?
A. R5(config-if)#ip bandwidth-percent eigrp 55 80
B. R5(config-pmap-c)#priori1y percent 80
C. R5(config-if)#ip bandwidth-percent eigrp 80 55
D. R5(config-if)#ipv6 bandwidth-percent eigrp 80 55
E. R5(config-if)#ipv6 bandwidth-percent eigrp 55 80
Answer: A

Which two protocols can be affected by MPP? (Choose two)
A. POP
B. SMTP
C. HTTP
D. SFTP
E. SSH
Answer: C E

Refer to exhibit. Which two reasons for IP SLA tracking failure are likely true? (Choose two)
R1(config)#ip sla 1
R1(config-ip-sla)#icmp-echo 172.20.20.2 source-interface FastEthernet0/0
R1(config-ip-sla-echo)#timeout 5000
R1(config-ip-sla-echo)#frequency 10
R1(config-ip-sla-echo)#threshold 500
R1(config)#ip sla schedule 1 start-time now life forever R1(config)#track 10 ip sla 1 reachability
R1(config)#ip route 0.0.0.0 0.0.0.0 172.20.20.2 track 10
R1(config)#no ip route 0.0.0.0 0.0.0.0 172.20.20.2
R1(config)#ip route 0.0.0.0 0.0.0.0 172.30.30.2 5
A. The source-interface is configured incorrectly
B. The destination must be 172.30.30.2 for icmp-echo
C. A route back to the R1 LAN network is missing in R2
D. The default route has wrong next hop IP address
E. The threshold value is wrong
Answer: C E

Refer to the exhibit.
A network engineer is working on the network topology and executes the command no ip split horizon on interface S0/0 of the Hub router. What is the result of this command?
A. A routing loop is created.
B. Each of the spoke routers can see the routes that are advertised from the other spoke routers.
C. The Spoke routers can see the routes that are advertised by the hub router.
D. The hub router can see the routes that are advertised by the spoke routers.
Answer: B

Which value does a point-to-point GRE tunnel use to identify a peer?
A. MAC address
B. configured multicast address
C. DLCI
D. IP address
E. VC ID
Answer: D

A network engineer has configured GRE between two IOS routers. The state of the tunnel interface is continuously oscillating between up and down. What is the solution to this problem?
A. Create a more specific static route to define how to reach the remote router.
B. Create a more specific ARP entry to define how to reach the remote router.
C. Save the configuration and reload the router.
D. Check whether the internet service provider link is stable
Answer: A

Refer to the exhibit. You want router R1 to perform unequal-cost routing to the 192.168.10.0/24 network. What is the smallest EIGRP variance value that you can configure on R1 to achieve this result?
A. 1
B. 2
C. 3
D. 4
Answer: C

Which value does a Cisco router use as its default username for CHAP authentication?
A. Its own hostname
B. chap
C. Cisco
D. ppp
Answer: A

Last Question

Which IP SLA operation can be used to measure round-trip delay for the full path and hop-by-hop round-trip delay on the network?
A. ICMP path Jitter
B. ICMP path echo
C. ICMP Jitter
D. ICMP echo
Answer: B

A network engineer wants to notify a manager in the events that the IP SLA connection loss threshold reached. Which two feature are need to implements this functionality? (Choose two)
A. MOS
B. Threshold action
C. Cisco IOS EEM
D. SNMP traps
E. logging local
Answer: B D

The enterprise network WAN link has been receiving several denial of service attacks from both IPv4 and IPv6 sources. Which three elements can you use to identify an IPv6 packet via its header, in order to filter future attacks? (Choose three)
A. Traffic Class
B. Source address
C. Flow Label
D. Hop Limit
E. Destination Address
F. Fragment Offset
Answer: A C D

Which keyword of the AAA authentication PPP command supports PAP only?
A. line
B. krb5
C. local
D. local-case
E. enable
Answer: B

Which two commands would be used to troubleshoot high memory usage for a process? (Choose two)
A. router#show memory allocating-process table
B. router#show memory summary
C. router#show memory dead
D. router#show memory events
E. router#show memory processor statistics
Answer: A B

Which two debug commands can you use to view issues with CHAP and PAP authentication? (Choose two)
A. debug tacacs
B. debug ppp authentication
C. debug radius
D. debug aaa authentication
E. debug ppp negotiation
Answer: B E

A network engineer wants an NTP client to be able to update the local system without updating or synchronizing with the remote system. Which option for the ntp access-group command is needed to accomplish this?
A. Serve
B. Serve-only
C. peer
D. Query-only
Answer: A

A network engineer wants to implement an SNMP notification process for host machines using the strongest security available. Which command accomplishes this task?
A. router(config)#snmp-server host 172.16.200.225 traps v2c auth
B. router(config)#snmp-server host 172 16.200.225 traps v1
C. router(config)#snmp-server host 172.16.200.225 traps v3
D. router(config)#snmp-server host 172.16.200.225 traps v2c
Answer: C

To configure SNMPv3 implementation, a network engineer is using the AuthNoPriv security level. What effect does this action have on the SNMP messages?
A. They become unauthenticated and unencrypted.
B. They become authenticated and unencrypted.
C. They become authenticated and encrypted.
D. They become unauthenticated and encrypted.
Answer: B

https://www.digitaltut.com/route-questions-and-answers
Good Luck

Hello everyone, cleared my route exam yesterday with a score of 925/1000. I can assure that the dumps are valid and simulations are similar with some changes. I am not a spammer or dump advertiser so you can be assured with the credibility of this. Though there were some questions not found in this dump but I have a document which has those, I am posting the link, you guys can download, I will be removing the file after few days so if someone can replicate the file, it would helpful for future test takers. Cheers!!
Simulations were ospf eigrp redistribution case 2, pbr and ospf simulation. D&D I don’t remember top of my head but were Frame relay, AAAs and CoPP MPP.
the link without *
https:/*/drive.google.com/open?id=1__RqlLMxJtApZBrbCgyIRo3ZNr1vHIwk

Passed route today 888/1000

I used lead to pass dumps and this website was a great asset. Email me at danger.highvoltage at hotmail .com

Everyone including me gets the Lab
PBR
EIGRP/OSPF redistribution
OSPF Simlet

8 Drag & Drops

Which value does a Cisco router use as its default username for CHAP authentication?
A. Its own hostname
B. chap
C. Cisco
D. ppp
Answer: A

Last Question

Which IP SLA operation can be used to measure round-trip delay for the full path and hop-by-hop round-trip delay on the network?
A. ICMP path Jitter
B. ICMP path echo
C. ICMP Jitter
D. ICMP echo
Answer: B

A network engineer wants to notify a manager in the events that the IP SLA connection loss threshold reached. Which two feature are need to implements this functionality? (Choose two)
A. MOS
B. Threshold action
C. Cisco IOS EEM
D. SNMP traps
E. logging local
Answer: B D

The enterprise network WAN link has been receiving several denial of service attacks from both IPv4 and IPv6 sources. Which three elements can you use to identify an IPv6 packet via its header, in order to filter future attacks? (Choose three)
A. Traffic Class
B. Source address
C. Flow Label
D. Hop Limit
E. Destination Address
F. Fragment Offset
Answer: A C D

Which keyword of the AAA authentication PPP command supports PAP only?
A. line
B. krb5
C. local
D. local-case
E. enable
Answer: B

Which two commands would be used to troubleshoot high memory usage for a process? (Choose two)
A. router#show memory allocating-process table
B. router#show memory summary
C. router#show memory dead
D. router#show memory events
E. router#show memory processor statistics
Answer: A B

Which two debug commands can you use to view issues with CHAP and PAP authentication? (Choose two)
A. debug tacacs
B. debug ppp authentication
C. debug radius
D. debug aaa authentication
E. debug ppp negotiation
Answer: B E

A network engineer wants an NTP client to be able to update the local system without updating or synchronizing with the remote system. Which option for the ntp access-group command is needed to accomplish this?
A. Serve
B. Serve-only
C. peer
D. Query-only
Answer: A

A network engineer wants to implement an SNMP notification process for host machines using the strongest security available. Which command accomplishes this task?
A. router(config)#snmp-server host 172.16.200.225 traps v2c auth
B. router(config)#snmp-server host 172 16.200.225 traps v1
C. router(config)#snmp-server host 172.16.200.225 traps v3
D. router(config)#snmp-server host 172.16.200.225 traps v2c
Answer: C

To configure SNMPv3 implementation, a network engineer is using the AuthNoPriv security level. What effect does this action have on the SNMP messages?
A. They become unauthenticated and unencrypted.
B. They become authenticated and unencrypted.
C. They become authenticated and encrypted.
D. They become unauthenticated and encrypted.
Answer: B

Congratulations! Passed.

– SNMP inform v/s trap
– Types of uRPF
– ip nat tcp [ip adddress] 8080 [ip address] 80, what happen in that command? how NAT translate that?
– Lots of IP SLA Questions.
– Same lab
– New DD about AAA but it almost the same
– Like two new EVN questions
– SNMP new questions about how works

Without 1 star**
https:/*/zkrt.cz/F0i

Which command can be entered on router R5 to configure 80 percent of the bandwidth of a link for EIGRP Autonomous System 55?
A. R5(config-if)#ip bandwidth-percent eigrp 55 80
B. R5(config-pmap-c)#priori1y percent 80
C. R5(config-if)#ip bandwidth-percent eigrp 80 55
D. R5(config-if)#ipv6 bandwidth-percent eigrp 80 55
E. R5(config-if)#ipv6 bandwidth-percent eigrp 55 80
Answer: A

Sheikh is FAKE FAKE FAKE

Sheikh is FAKE FAKE FAKE

Sheikh is FAKE FAKE FAKE

Passed guys, it’s an easy exam if you have the basis plus review whatever gets posted on this forum. July dumps do the job. However, pay attention to every single detail, Cisco changed OSPF eval sim and slightly other questions.

Good luck

where is july dump ????
there is
Most Popular Questions
New Updated Questions – Part 5
New Updated Questions – Part 6

KuKuYu

Refer to exhibit. Which two reasons for IP SLA tracking failure are likely true? (Choose two)
R1(config)#ip sla 1
R1(config-ip-sla)#icmp-echo 172.20.20.2 source-interface FastEthernet0/0
R1(config-ip-sla-echo)#timeout 5000
R1(config-ip-sla-echo)#frequency 10
R1(config-ip-sla-echo)#threshold 500
R1(config)#ip sla schedule 1 start-time now life forever R1(config)#track 10 ip sla 1 reachability
R1(config)#ip route 0.0.0.0 0.0.0.0 172.20.20.2 track 10
R1(config)#no ip route 0.0.0.0 0.0.0.0 172.20.20.2
R1(config)#ip route 0.0.0.0 0.0.0.0 172.30.30.2 5
A. The source-interface is configured incorrectly
B. The destination must be 172.30.30.2 for icmp-echo
C. A route back to the R1 LAN network is missing in R2
D. The default route has wrong next hop IP address
E. The threshold value is wrong
Answer: C E wrong !!!!

Ans is A and C

i told you that i passed the exam, i took 938 point. All the questions are in route_july2019 and digital premium. don´t buy any dump it´s not necessary.

55 q
4 drag and drop
2 labs ospf and eigrp redistribution / route map pbr

Special attention: commands copy running -config startup – config / copy run start / wr doesn ´t work , but in my opinion, you still have to write these commands.

thanks to everyone!!!!

Do you know of any site as digital but to prepare the ccie r & s?

Hi guys, If anyone have valid dumps file with less questions please shear the file link.

and also lab’s simulations

thanks in advance

spyboot go to rstut

@spyboot
where is july dump ????
there is
Most Popular Questions
New Updated Questions – Part 5
New Updated Questions – Part 6

@mamadoo10 check on Route FAQs and Tips then go pint number 15 you will see the link to download the PDF

Were there any new questions in the exam? Please post it here brothers

Hi all,
I passed today with 9xx score, the july PDF is definitely valid and I strongly recommend you to subscribe to the premium membership definitely worth it, to practice the questions and the Lab

regarding the Labs,
Pbr: the same just change in the IPs
redistribution : I think it’s the same ( the case with the distance eigrp)
ospf evaluation: changed, defiantly double check everything

D&D: I had 4 or 5 all from the site

good luck .

what specifically has changed in the ospf eval?

can you go into detail please?

CH

What’s wrong with sourcing the LAN interface?

Is this answer correct? Please help me. Thank you.

Question 4
Refer to the exhibit.

interface FastEthernet0/1
ip address 209.165.200.225 255.255.255.224 ip nat outside
!
interface FastEthernet0/2
ip address 10.10.10.1 255.255.255.0
ip nat inside
!
access-list 10 permit 10.10.10.0 0.0.0.255
!

Which command allows hosts that are connected to FastEthernet0/2 to access the Internet?
A. ip nat inside source list 10 interface FastEthernet0/1 overload
B. ip nat outside source static 209.165.200.225 10.10.10.0 overload C. ip nat inside source list 10 interface FastEthernet0/2 overload
D. ip nat outside source list 10 interface FastEthernet0/2 overload
Answer: A

Hi Guys, Do you know any whatapp group for studying route exam.If so, could you please share the link.Thanks in advance.

Hi Dear Friends,
İ need valid dump.
Please, can anybody send me valid dump? My exam will be on this Wednesday

ekerimov1988 at gmail.com

What are the usual labs that I could encounter in these days regarding route 300-101 exam?

Passed the exam. 5-6 questions were new.
Lab: PBR, Redistribution.
4-5 D & D
Study July file

All the best

ip http server listens on port 80
ip https secure-server listens on port 443 by default
ip https secure-port command changes default 443 port to different value

port 80 = HTTP
port 443 = HTTPS

In my opinion answer A is correct.

Can you please send me the latest dump?

My email is frotan.kadze (a) gmail.com

Thanks in advance.

Frotan.

can some one send me the july dumps

please send july dumps to sasharocks0719atgmail

I just pass my 300-101 Exam with 9XX Score.
my advice just focus on D&D – LABs – MPQ – part 5- Part 6. thank you Digital TUT. I would say 99% was there- good luck

Passed today with 9XX. Nearly all the questions were here. had OSPF Eval, route redistribution, and PBR sims. Drag and drops were all AAA based. On the OSPF Eval sim, the question regarding the R3 serial links was different. answer was to use the neighbor command, as timer values were different. other wise the only difference was ip addresses used on the sims. Like Syassa said, 99% questions were from here. didn’t use or need dumps from anywhere else.

Which type of address does OSPFv3 use to form neighbor adjacencies and to send LSAs?
A. unicast IPv6 addresses
B. link-local addresses
C. multicast address FF02::5
D. unicast IPv4 addresses

Answer: C or B ?

Hi, does anyone know how much the exam changes on your second try?

A network engineer executes the ―show ip cache flow‖ command. Which two types of information are displayed in the report that is generated? (Choose two)
A. top talkers
B. flow export statistics
C. flow sample for specific protocols
D. MLS flow traffic
E. IP packet distribution

Answer: C E or B E ?

Alhamdulillah passed yesterday with 86x

Labs: PBR, OSPF-EIGRP Redistribution, OSPF Sim

any one need dumps inbox me

noorkhanpk1978 at gmail dot com

Passed… thanks
DnD: Plenty
PBR, OSPF Eval, and Redis – practice everything in GNS3 or will end up adding wrong commands
A lot of NATv6 related questions
Be careful with some commands, seems like gotta remember whether it goes on the interface or global or router

please send july dumps to jodoi1819 at hotmail dot com

Just Passed today and all questions are here… i did not encounter any new questions, labs and drag and drops are all here

please send july dumps to rratlos76 at gmail dot com

any changes to the sims at all?

CH

hi, can anyone please share the link to get the July digital tut dumps.
please post link here, thank you

for people asking for July dumps and do not want to read back. here https://www.digitaltut.com/route-questions-and-answers.

Passed.

Labs: PBR, redistribution, sim-ospf r1-r3 is non-broadcast answer that it’s necessary to configure neighbor explicitly.

D&D all here, I had maybe 5.

Questions: Something was new for me, something was changed, something was known.

Passed a lot of materials for this test, that’s why it’s difficult to tell where the information was took, however digitaltut is one of the best resources, my opinion that it’s necessary to have a good practical experience, to read a guide and to resolve dumps, just one thing of this list isn’t enough.

Thank you digitaltut!

Good luck for all!

answer is c and e.

Pass today with 901 , as the other mention before july dump is enough. Lab PBR , OSPF Eval , Redistribute. Good luck Guy. thank digital tut

@Myanmar student did you study old questions from july file or only MPQ and NuQ5 And NuQ6?

Hi, just passed. There were 2mcq that i couldn’t remember from dumps. But it might be because of my poor memory.
Labs:redist, pbr, ospf sim. Good luck all…

any changes in the labs at all? CH

just passed today with 888. i study july dump only.
Lab: ospf eval sim, pbr, eigrp ospf redistribute (need to configure shortest path on fastethernet).
thanks digtaltut!!!