Share your ROUTE v2.0 Experience

@sky

For question 23, there were many option proposed here.

Which tow commands must you configure in the calling router to support the PPPoE client? (Choose two)

First need to figure out whether this question ask about how to configure a router as a PPPoE client or PPPoE server.

If PPPoE client then the answer will be
mtu
pppoe-client dial-pool-number

If PPPoE server then the answer will be
bba-group pppoe
pppoe enable group

Please share your thoughts.

THAT was my outcome.. make sure to understand the question guys

@soso thanks for explanation .. @ciscodady thank you boss for you worth sharing here after passing exam you are still here to guide us.. :)

@soso and @maximoo need your response on following Q

34. Other than a working EIGRP configuration, which option must be the same on all routers for EIGRP
authentication key role over to work correctly?
A. SMTP
B. SNMP
C. Passwords
D. Time

Answer: D

but in some dumps and Pdf the answer is “C”

I check and search about it , the link below explain the ans should be “D”

http://www.ciscopress.com/articles/article.asp?p=687478&seqNum=4

nps @CiscoTake good luck ;)

I am facing issue while configuring IPv6 OSPF virtual link sim as there is no pre-configured ipv6 OSPF in topology, downloaded from the link here for GNS3 labs

if i just want to practice configurations then router in topology c2691 yields error and does not allow even ipv6 unicast-routing command

R1(config)#ipv6 unicast-routing
^
% Invalid input detected at ‘^’ marker.

if any one have any idea please assist me …

@CiscoDaddy @soso @maximo

HELP!!! HELP!!! HELP!!!

Can anyone help me with EIGRP OSPF Redistribute Sim ??

How to find out the EIGRP metrics when redistributing EIGRP to OSPF ?

Which interface do I have to look while choosing those values??

Digital tut has used two values :

redistribute ospf 1 metric 1544 2000 255 1 1500

AND

redistribute ospf 1 metric 10000 100 255 1 1500

I am not sure where they used 1544 for bandwidth??

Thank you..

@CiscoDaddy

I need your help…

How did you find out the metrics of EIGRP in EIGRP-OSPF DISribution SIm?

Thank you.

@ ma nepali

these are commands for OSPF to redistribute in eigrp …

and for your confusion about interface you can see in topology R2 have only 1 int s 0/0/0 in ospf rest of 2 serial intfaces are in EIGRP so for redistribution of OSPF you need to check INT S0/0/0

similarly for R3 only Fa 0/0 is in OSPF so you need to check its interface properties to use as metric

serial int face have lower bandwidth 1544 as compared to Fa

hope this will make sense for you ….

Someone can help me.

I did the PBR configuration. Then how can I verify it is working or not.

Which three benefits does the Cisco Easy Virtual Network provide to an enterprise network? (Choose three.)
A. simplified Layer 3 network virtualization
B. improved shared services support
C. enhanced management, troubleshooting, and usability
D. reduced configuration and deployment time for dot1q trunking
E. increased network performance and throughput
F. decreased BGP neighbor configurations

Answer: ABC or BCD???

Which command prevent routers from sending routing update through router interfaces?
A.passive-interface
B.Distribute-list out
C.defaultmetric0
D.Distribute-list in

the ans A or B

@Bravo
the ans is ABC

@Khaled passive interface command disable routing updates f0r particular interface of router

@ashik

telnet ——–(IP address of destination) 80 execute this command from testing host

and meanwhile go to border router and check packets passing through border router towards destination through command “show ip route

TCP traffic is blocked on port 547 between DHCPv6 relay agent and DHCPv6 served that is configured for prefix delegation, which two outcomes will result when relay agent is rebooted? (choose two)
A.router will net obtain DHCPv6 prefix
B.DHCPv6 clients will be unreachable
C.Host will not obtain DHCPv6 address
D.the DHCPv6 relay agent will resume distributing addresses

Ans. is AC or AD ?

Can somebody share me the link to download latest VCE manager software for free

which type of information is displayed when a network engineer executes the show track 1 command on router?

A.information about tracking list 1
B. time to next poll for track object 1
C. tracking information statistic
Ans is A or C ??

@Cisco Take Thank you so much.

In my case The ISP1 interface ip 10.1.101.1 so i have to telnet to this IP right.

befor telnet do I want to enable telnet on ISP1?

I have a pdf it saying in border router We have to check Show route-map and result should be like this (Policy routing matches:9 packets)

Passed today with 9xx/1000

Thanks to all those who contributed here .. this is an excellent forum to prepare for Cisco exams

It’s me vce v1.3/4 or Procyber are still 100% valid plus 10 to 12 new questions which have been discussed here in last 3 to 4 weeks – but make sure you guys keep checking this forum for any new updates or changes

DND nothing new:
AAA Authentication
NAT64/NPTv6 Characteristics
Frame Relay DLCI/SVC/LMI/FECN/PVC
Strict/ Loose Mode
and may be 2 to 3 more but all from it’s me vce

LABS
EIGRP OSPF redistribution – pretty much same , link between R2 and R3 was fast ethernet so i configured “distance eigrp 90 105” on R2
OSPF Lab Sim – same lab just different names, process IDs and area – so ready carefully before start configuring routers
PBR – next hop 10.1.101.2 but again this may change so please be careful
EIGRP Simlet – same answers.
OSPF Simlet – 3 out 4 questions were same – just be careful about 4th question below

Check the serial links connected to R3. Which statements are correct?
A. The neighbor command must be used on R1-R3 link to keep the adjacency up
B. The OSPF timer values of R2-R3 link are 30, 120, 120
C. The OSPF timer values of R1-R3 link should be 10,40,40
D. R3 must flood LSUs to all the routers on the network.
Make sure you use “show cdp neighbors” command on R3 to check which interface pointing towards which router
According to Topology it was showing R3 s1/0  R2 to R3 s1/1 to R1 but when I used “show cdp neighbors” then it was R3 s1/1  R2 to R3 s1/0 to R1
So I went according to what I got from “sh cdp neighbors” command and found below
Network Type between R2-R3 was not NON_BROADCAST but rather it was Point to Point so it has different timers and not (30,120,120) which means Option “B” is not correct
In this case Option “A” is correct

Hope this feedback helps

@ Cisco Take

Can you please share your Lab materials so I can catch it more efficiently .

ashikonline92 at gmail com

@Fiddy

Congrats …….

Can you please share your lab materials

ashikonline92 @ gmail com

Thanks in advanced

@Ashik

You can download zip files of all labs from below links to practice in GNS3

https://www.digitaltut.com/category/route-300-101/lab-sim

https://www.digitaltut.com/practice-real-route-labs-with-gns3#more-672

Good luck

can someone share 10-12 new questions ?

@fiddy Congragulation first of all
Please advice on the below doubts in the PBR questions
1. Did you applied “route-map PBR permitt 20” additionally?
2. Was there any option for you availabe in the lab to generate HTTP traffic in the simulation ?

@ashik

no need to enable telnet anywhere just telnet your isp from testing host (in your case telnet 10.1.101.1 80 ) and switch to border router and execute command show ip route and see under route map seq number(which you specify while configuring route-map) there will be packets and traffic in kbps …

Guys does the 10-12 questions are included in :
300-101-ROUTEv1.5 (updated by procyber 01.11.2017) ?

@sky

No I did not apply “route-map PBR permitt 20” as it was not needed

Yes there is option on “a workstation” given in the topology to generate HTTP traffic and then you can verify it by typing “show route-map” on border router to see few packets, which will confirm that route-map is configured correctly

@fiddy thanks for the reply.

if you don’t mind sharing your email. I will be doing my exam in 3 days. May be any doubts in exam can reach through your email incase you are not available here

My email id is {email not allowed}

@fiddy My email id is hrrandrewgmailcom

@fiddy congratx dear for passing the exam can you please let me know those 10-12 new questions are included in its me vce1.5 or not if you have them please share that or email me {email not allowed}

@fiddy my email address is akbari.fakhruddinatgmaildotcom please send the materials

Guys !
Can someone please share the 10-12 new questions

Dear All,

All questions are shared by It’s Me on pg 190-195 i think … ans are not 100 % correct you can discuss if feel something wrong …

1. Which netflow version supports MPLS:
a) none
b) all of them
c) version 8 and 9
d) version 9
Answer: D
2.What is the minimum log level for the event generated when an ACL drops a packet?
a) 4
b) 5
c) 3
d) 7
e) 6
Answer: E
Example:
%SEC-6-IPACCESSLOGP: list Block_SSH denied tcp 192.168.0.42(30316) -> 1.1.1.1(22), 1 packet
3. What other action does an ipv6 filter do when it drops a packet?
a) option 1
b) option 2
c) generates an ICMP unreachable message
d) option 4
Answer: C (it’s in fact a “Destination Unreachable” message)
As in ICMPv4, in ICMPv6 this is done with Destination Unreachable messages. Each message includes a code that indicates the basic nature of the problem that caused the datagram not to be delivered,
and includes all or part of the datagram that was undelivered, to help the source device diagnose the problem.
From RFC 4443:
A Destination Unreachable message SHOULD be generated by a router, or
by the IPv6 layer in the originating node, in response to a packet
that cannot be delivered to its destination address for reasons other
than congestion. (An ICMPv6 message MUST NOT be generated if a
packet is dropped due to congestion.)
4. What is the NHRP role in DMVPN? (Choose 2)
a) obtains the next-hop to be used for routing
b) routes the packet through the tunnel
c) identifies the PIM-SM RP used to route the packet
d) don’t remember
Answer: A,B ——–> Not Sure but this is the answers till now
5.A network Engineer received a company network performs slow . Which command he need to execute ?
1. Show track
2. Show reachability
3. Show connectivity
4. Option 4
Answer : 1(Guess)
6.Which problem can be caused by latency on a UDP stream?
A. The device that sends the stream is forced to hold data in the buffer for a longer period of time.
B. The overall throughput of the stream is decreased.
C. The device that receives the stream is forced to hold data in the buffer for a longer period of time.
D. The devices at each end of the stream are forced to negotiate a smaller window size.
Answer: C
7. Where does the EVN marks the traffic to separate different users ? (something like that)
A. on the edge interface, with vnet tag
B. on the edge, with 801.q
C. on the trunk, with vnet tag
D. on the trunk, with 802.1 q
Answer : C —–> Discussions going on

Hi
Below are the LABS O Compiled in GNS3. I have also included the IOS file as well.
https://drive.google.com/open?id=1QXyadvGzUSOyJccmkV7Ui0nB_dfsTs6Y

Below contains the part of new question. But strongly recommend to go through the previous post at least with in 2 weeks to check any veify the answers
https://drive.google.com/open?id=1ZKFCK8h4v4-AS4Vz3AdCLHNKPJovD2c9

@ sky
Thanks !

4. What is the NHRP role in DMVPN? (Choose 2)
a) obtains the next-hop to be used for routing
b) routes the packet through the tunnel
c) identifies the PIM-SM RP used to route the packet
d) don’t remember
Answer: A,B ——–> Not Sure but this is the answers till now

but the officiel question is
Which two statements about NHRP in a DMVPN environment are true? (Choose two)
a. It requires each endpoint to have a unique network ID
b. It routes traffic through the tunnel
c. It can identify PIM-SM RPs over a tunnel
d. It can authenticate VPN endpoints
e. It provides address resolution to route traffic
answer: D and E 100% sure

@sky can you please share ipv6 ospf virtual link lab for gns3 v 0.8.x as the file here in digitaltut is not configured properly and i am unable to configure ipv6 on c2691 …

or else if i upgraded to gns3 2.0.3, can you please make sure all the labs will work ????

@ma nepali

why you are still confuse as serial interface have lower bandwidth as compare to fast Ethernet so serial link show very low BW i.e 1544 as compare to Fa i.e 100000 ….. dont remove or devide BW by 100 may be by mistake in configuration they remove 1 zero for BW … so dont worry about it whatever you find in exam put that value for BW … as of my understanding , dividing by 100 to delay value is for all cases..

follow the procedure and you can see at the end route redistribution successfully…

Hello, how can you randomize the answers for the questions in the VCE player?

@holymoly

before start the exam in vce player on top right side there is dropdown … you can open settings then there is option for randomizr questions as well as options (MCQs) arrangement

@CiscoTake No such thing on my simulator, could you perhaps like me your version of the VCE player?

@holymoly

Bluestacks version 3.50.60 and A+ VCE silver

@Sky @soso @fiddy

I do my exam in to day please do you have any actualisation my email is…. m a x i m o i v a @ H O T M A I L . C O M

@ REGULAR

ARE YO SURE WHY NOT E AND A

@CISCO TAKE

ANY NO QUESTION

@FIDDY

A NEW QUESTION

@sky –> Thanks for sharing Labs. However I am having difficulties to open them as the error message says that the path where the configs should be located does not exist. Any way how to rewrite the path to find config files?

Error message: “Cannot access the private-config C:/xxxxxxxx …….. [WinError 3] The system cannot find the path specified xxxxxxxxxx” I tried to trick system that I have that path but same problem occured. Any help is welcome. Thanks in advance.

@polaris

They are working, reboot your pc after GNS installation

@AS I have already installed GNS3 quite some time…so I know it should work, but it doesn’t for some reason…

bust of luck @ maximo .. i believe you can do it dont be afraid bro…

dont forget to share your post exam experience with us …

@soso and all
here is the answer to your question :
4. What is the NHRP role in DMVPN? (Choose 2)
a) obtains the next-hop to be used for routing
b) routes the packet through the tunnel
c) identifies the PIM-SM RP used to route the packet
d) don’t remember
Answer: A,B ——–> Not Sure but this is the answers till now

Answer from the Cisco press CCNP Route – Quick Reference: I will copy the full paragraph of the book so you can understand.

DMVPN
Configuring a full mesh of GRE or IPsec tunnels becomes unwieldy as
the network grows in size. Dynamic Multipoint Virtual Private Network
(DMVPN) dynamically creates IPsec tunnels on demand, thus easing the
administrative burden. DMVPN leverages multipoint GRE (mGRE), IPsec,
and Next Hop Resolution Protocol (NHRP). The hub site(s) creates an
mGRE tunnel interface. Each of the remote sites (spokes) is configured with
information about the hub and initiates a tunnel with the hub. The hub uses
NHRP to map each spoke’s tunnel IP address to its physical address.
When one spoke wants to send traffic to another, it uses an NHRP query to
ask the hub for the physical next-hop address of the other spoke. It can then
build a dynamic tunnel to that spoke.
DMVPN is a good choice when spoke-to-spoke connections are needed
because traffic does not have to traverse the hub. It also supports multicast
and routing protocols between the hub and the spokes.

the answer A and B to me is correct

@CiscoDaddy
Yes, I am currently preparing for route exam from all the material I have. if you want leave your email and ill send it to you

Hey Ada, please mail me the materials that you have for CCNP route.

My email id is rash.khnl @ gmail.com