Share your ROUTE v2.0 Experience

Hi Guys,
Happy New Year!!!
Where can i get the latest dump and vue for routing?
Don’t mind sharing. Thank you so much. =)
Sharing is caring. =)

Can anyone explain or share documentation about
“IPsec encryption not supported with statically addressed spokes”

Which two statements about DMVPN are true? (Choose two)
A. IPsec encryption not supported with statically addressed spokes
B. It requires full-mesh connectivity on the network
C. It uses NHRP to create a mapping database of spoke addresses
D. Multicast traffic is not supported
E. It supports dynamic addresses for spokes in a hub-and-spoke VPN topology
AC

The answer A doesn’t make sense to me.

Which two statements about DMVPN are true? (Choose two)
A. IPsec encryption not supported with statically addressed spokes
B. It requires full-mesh connectivity on the network
C. It uses NHRP to create a mapping database of spoke addresses
D. Multicast traffic is not supported
E. It supports dynamic addresses for spokes in a hub-and-spoke VPN topology
AC
The answer is C and E

@Anonymous answer
yes, E makes sense, but dumps say A, so I wanted to make sure if there is indeed an explanation.

any1 got updates about the exam ? new questions ? I want to have the exam mid January.

I need the latest updated ccnp routing questions in vce file
You can send them to me

email: {email not allowed}

I need the latest updated ccnp routing questions in vce file
can You send to me

{email not allowed}

I need the latest updated ccnp routing questions in vce file
You can send them to me

can share the link url

Hello, can someone share me the simulations?

Hi sol,
do u have any link for CCNP dumps,
share and held us, skraon @ gmail dot com

What configurations does PPPoE allow? (Choose two)

A. Client can be installed on the same network devices as server
B. 8 clients can be configured on 1 CPE
C. Clients can connect to multiple hosts over DMVPN
D. Client connecting over ATM PVC
E. Client installed on native IPv6 network
BC
I think the answer should be BD, not C, Can anyone explain why C,

@yes boss, thanks

@john can you elaborate or provide documentation, please? Why not E, but A

Can someone share with me SPOTO 227 and Q757?

Email: ulkumada at yandex.com

Thanks.

Question 222

Company is deploying a multicast application that must be accessible between sites, but must not be accessible outside of the organization. Based on the scoping requirements, the multicast group address for the application will be allocated out of which range?

A. FF00:/16
B. FF0E:/16
C. FF02:/16
D. FF08:/16

Answer: C or D???

Hi all,

can anyone explain me where i can get the latest spoto dump?

Thanks in advance

Hi guys, this website is enough to pass the CCNP Route exam. There is no need to purchase the premium subscription, since the latest pdf updates is enough, but if you have extra bucks, you can do so to help the people behind this awesome website :D

Labs:
EIGRP Stub (1 EIGRP Stub + 1 Router that needs auto-summary)
EIGRP Evaluation (Show commands about Traffic Ratio, Bandwidth, etc.)
OSPF Troubleshooting (1 OSPF Stub + 1 OSPF Stub No-summary)

Drag and Drop
MPP versus CoPP
Loose versus Strict
Frame Relay Point-to-Point Steps
IPv6 Traffic Filter versus IPv6 Access Class
AAA (Auth-proxy, Command, Exec, Connection, Reverse Telnet) – NEW AND NOT FOUND HERE

Thank you, Digital Tut. If my tip helps you pass the exam, kindly share the new questions too for the sake of the future takers. Thank you.

Uper Link is Fake

Olivia is fake fake fake fake

Don’t Use Olivia Link
Olivia Is fake

Hi All
i am seeing answers wrong in SPOTO and 9TUT.
Example globla command is it (config)#service dhcp or (config)#ip dhcp relay
i assume 9TUT also could be wrong on this one any comment

please what is answer?

Which two statements about errdisable recovery are true? (Choose two.)
A. You can use the show errdisable recovery command to view the reason a port was error-disabled.
B. Errdisable detection is enabled by default on ports with port security enabled.
C. You can use the show errdisable detect command to view the reason a port was error-disabled.
D. Errdisabled autorecovery is enabled by default.
E. Errdisabled detection is disabled by default on ports with port security enabled.

Correct answer A,B options.
https://www.cisco.com/c/en/us/support/docs/lan-switching/spanning-tree-protocol/69980-errdisable-recovery.html

Check above link for answer

There are various reasons for the interface to go into errdisable. The reason can be:

Duplex mismatch

Port channel misconfiguration

BPDU guard violation

UniDirectional Link Detection (UDLD) condition

Late-collision detection

Link-flap detection

Security violation

Port Aggregation Protocol (PAgP) flap

Layer 2 Tunneling Protocol (L2TP) guard

DHCP snooping rate-limit

Incorrect GBIC / Small Form-Factor Pluggable (SFP) module or cable

Address Resolution Protocol (ARP) inspection

Inline power

Witch drag and drop questions should I learn to exam

Can someone share drag and drop questions ?

@NSK thank you very much

@Yoshimitsu

Question:

Company is deploying a multicast application that must be accessible between sites, but must not be accessible outside of the organization. Based on the scoping requirements, the multicast group address for the application will be allocated out of which range?
A. FF00:/16 B. FF0E:/16 C. FF02:/16 D. FF08:/16
Answer: C

Explanation
All IPv6 multicast addresses begin with FF::/8 – in other words, with FF as the first two digits. Multicasts with a link local scope, like most of the multicast addresses referenced, begin with FF02::/16, the 2 in the fourth hex digit identifies the scope as link local. A fourth digit of hex 5 identifies the broadcast as site local scope, with those multicasts beginning with FF05::/16
Reference: CCNP ROUTE 300-101 Official Certification Guide

It would be D. FF02 is for link-local multicast and FF08 is for organization local multicast.

From what I can remember, the only thing configured on the serial interfaces was an ipv4 address and maybe the clock rate. Specifically, as far as any ipv6 addressing, there was none on the serial interfaces. No auto config, no hard coded ipv6 on the serial. This much I can remember for sure.

So I am still curious did anyone take exam, have the ospf virtual command sim and notice also that the Serial interfaces only had ipv4 addresses configured and no ipv6 address or any other ipv6 address configuration configured? On the ethernet interfaces there were ipv6 addresses, but not on the Serial interfaces.

which are the recommended labs to pass the CCNP Routes and from where we can get the simulations

300-101 exam passed on 4/Jan/2019!!! 850 points, the passing line is 790 now!!!

Total 53 questions. 4 Drag and Drop FYI: frame relay, ACL, AAA, DHCPv6.

Labs: eigrp case, eigrp stub, route-map

Mainly learned the latest Pass Leader 300-101 dumps (758q NEW VERSION UPDATED in Jan/2019!!!), stable and valid enough for passing!

Good luck!!!

Hi Tom,

Congrats!! Could you please share the pass leader 300-101 dumps to my mail id sankar.narayan8787 @ gmail. com thanks in advance

Can the pass leader document be posted? Or any of the new questions?

Hello All,

Is digitaltut paid dumps valid to score pass grade.
I have used networktut for tshoot and it was valid.

Please advise.
Thanks,
Arun

which are the recommended labs to pass the CCNP Routes

Hi Arun

Could you please share the dumps to my mail id sankar.narayan8787 @ gmail. com Thanks in advance

Hi all,

Where i can find any valid dumps?

TY!

Could you please share the dumps 300-101 to migdadi 2013 @ hotmail. c om

@john

“Which two statements about DMVPN are true? (Choose two)
A. IPsec encryption not supported with statically addressed spokes
B. It requires full-mesh connectivity on the network
C. It uses NHRP to create a mapping database of spoke addresses
D. Multicast traffic is not supported
E. It supports dynamic addresses for spokes in a hub-and-spoke VPN topology
AC”

This is incorrect. The answer is C & E. IPSEC is supported in DMVPN, a statically assigned IP address for a spoke wouldn’t make a difference in relation to being able to use IPSEC.

Thanks digitaltut community for this great platform.

Just cleared Route today.

Most of The question are covered in this platform.

Lab&Simlet( IPV6 ospf Virtual links, Eigrp stub and Eigrp Simlet )

Drag and Drop (URPF, NAT64, DMVPN(NHRP,HUB,SPOKE,mGRE)

The rest were Multiple choice which many are in this platform and few new ones were so obvious that you cant fail.

score 977 i missed two or Three multiple choice

1. GRE —-> i just found after the exam GRE is IP Protocol 47 (Not TCP not UDP)
I finished the exam 1 hour and 5 minutes before time.

I didnt have any question on BGP, Im kinda sad becuse i spend a lot on BGP but no worries the information learnt will be useful for CCIE exama

Hi Everyone,

I passed the exam today many thanks to all of you specially in RouterRaider, Ahamed & active guys in @share-your-route-experience comment section.

Thanks also on legit website for review for FREE digtaltut and examtopics

This is the exam i remember.

Lab
-EIGRP Stub Sim
-IPv6 OSPF Virtual Link Sim
-EIGRP Evaluation Sim

D&D
-NAT
-mGRE/IPsec
-Loose/Strict Mode

Tip: Just m@sturb@te after review whaha just kidding Study Smarter Not Harder haha

As blowout i will share my DUMP for FREE MADAFAKERS but sadly i cant share the link whahaha. Goodluck to future takers see you in TSHOOT

please check my new post in networktut under share your tshoot exp. i share my dumps there i dont know why i cant post my comment here. promise it will help you alot thx.

Is there similar site like this one, for CCNA Data centar exams??

@Mdachi Congrats! In iPV6 OSPF VL lab, were the serial links IPv4? I have seen comments about serial interfaces being IPv4, And was there “ipv6 ospf 1 area” command under loopback interface?

can somebody help me with the latest dumps. my email = jermain.l @ hotmail . com

@r3
no, C E, A. doesn’t make any sense and there is no documentation about it. You probably chose A because of dumps. There are many wrong answers in dumps.

@ chinaski

Do the serial links being ipv4 affect configuration? Would the solution available on digitaltut, now be incorrect? Just wondering since OSPF is being configured globally rather than per interface. A little confused.

hi guys,

can you share with me the 758q dumps please? i will appreciate me and lot of people too.

thank you!!

hi guys,

can you share with me the 758q dumps please? i will appreciate me and lot of people too.

thank you!

@Vinilee If the serial links are only IPv4 and Ethernet links are IPv6, then obviously the available solution won’t work and there should be a tunnel to pass IPv6 multicast over IPv4 network. That would change the whole lab.
By the way, the comment about IPV4 serial link is in “IPv6 OSPF Virtual Link Sim” Lab section.
What “OSPF is being configured globally rather than per interface” has o do with my question?

PLS S.O.S !!!! can somebody help me with the latest dumps. my email = jermain.l @ hotmail . com