Share your ROUTE v2.0 Experience

What were the subjects of the D&D’s?

How to redistribute Internal BGP routes into OSPF process. Like in other IGP to IGP redistribution the behavior is different when redistributing IBGP into OSPF. IBGP learned routes are not forwarded to an IGP routing protocol through the redistribute command. Use command “bgp redistribute-internal” under the BGP process on the redistributing router

@Nim, Thank you. I was just wondering if there were any differences between the PDF (from this site) and the questions on this site. Also, do the Composite Quizzes include ALL of the questions from the site and/or PDF?

can you please send dumps to vrpn 79 @ gmail dot com
Many thanks.

Firstly sorry about my English.

passed today with score 93x
Lab :
1. OSPF sim (Difference Area (42), Process ID (26) , IP 196.168.6.4/30 )
2. IPv6 OSPF virtual-link (Same)
3. Eigrp Evaluation (Same)

Most questions from MPQ , NUQ5 , NUQ6

MPQ : Q107 , 222 , 77 , 53 , 31a , 153 , 214 , 219 , 127 , 67 , 70 , 181 , 227 , 24 , 74a , 83 , 20 , 37 , 176 , 154 , 165 , 242 , 87 , 106 , 23 , 116 D&D framerelay, 206 D&D AAA , 245 D&D NAT process , 249 D&D , 255 , 257

NUQ5 : Q9 , 16 , 24 , 40 , 43 , 51

NUQ6 : Q10 , 18 , 25 , 34 , 40 , 44 , 45 , 46 and Q.50 between ospf and different autonomous systems << in my exam changed word to "different OSPF area" , So i ans C. config the area range command on the ABR

MPQ 17 Diagram with difference question
question about IBGP
question about situation about flooding
question about command eigrp variance=2 and maximum paths = 4

I failed yesterday, the exam was extremely had :(

i had six drag and draps……….ridiculous

the ospf sim i had to configure area 14 …. they did not even ping.

question got that i new was only 12………… :(:(

@RamZ
Did u get any new questions?

@RamZ,

thanks for this, how did you enter you commands for below?

Lab :
1. OSPF sim (Difference Area (42), Process ID (26) , IP 196.168.6.4/30 )

like this?

Router ospf 26
network 196.168.6.4 0.0.0.3 area 42
area 42 stub?

Hi Guys, please could someone help with these?

Q1-You want the devices on your network to summarize routes between OSPF and a different autonomous system. Which action must you take?
A- Configure the summary-address command on the ASBR
B- Configure the summary-address command on ABR
C- Configure the area range command on the ASBR
D- Configure the area range command on the ABR

Q2-You want the devices on your network to summarize routes between OSPF. Which action must you take?
A- Configure the summary-address command on the ASBR
B- Configure the summary-address command on ABR
C- Configure the area range command on the ASBR
D- Configure the area range command on the ABR

Ans C for Q1 and Ans D for Q2?

@Num Did u get any new questions?

– Only 3-4 new questions

@AKA
Router ospf 26
network 196.168.6.4 0.0.0.3 area 42
area 42 stub?

Yes. That’s right. and another router area 42 stub no-summary

Hi Guys, from RamZ’s exam feedback (Thanks again RamZ), I have found this question, please could someone help with the correct answer for this?

Exhibit
R1 (Config)# router eigrp 45
R1 (Config-router)# network 10.0.0.0
R1 (Config-router)# Variance 2
R1 (Config-router)# maximum path 4

Refer to the exhibit Currently, there is at least one route to the 10 0 0 0/8 network with a metric of 10 Which statement describes the outcome of applying this configuration?

A- The router performs only equal-cost load balancing on paths with metric greater than 2
B- If there is one path with metric of 10 and one path with metric of 20, two total paths are used
C- If there are two paths with metric of 10 and two paths with metric of 20, two total paths are used.
D- The first four paths with a metric less than 20 are added to the routing table

Hi

@digitaltut team, when wil you add new question in NQ6.

Example:
Exhibit
R1 (Config)# router eigrp 45
R1 (Config-router)# network 10.0.0.0
R1 (Config-router)# Variance 2
R1 (Config-router)# maximum path 4

Refer to the exhibit Currently, there is at least one route to the 10 0 0 0/8 network with a metric of 10 Which statement describes the outcome of applying this configuration?

A- The router performs only equal-cost load balancing on paths with metric greater than 2
B- If there is one path with metric of 10 and one path with metric of 20, two total paths are used
C- If there are two paths with metric of 10 and two paths with metric of 20, two total paths are used.
D- The first four paths with a metric less than 20 are added to the routing table

@AKA,

The correct answer is B

@Ekva you email is beulsins_sonny@yahoo. com ? i send to this email address

@AKA

Q1-You want the devices on your network to summarize routes between OSPF and a different autonomous system. Which action must you take?
A- Configure the summary-address command on the ASBR
B- Configure the summary-address command on ABR
C- Configure the area range command on the ASBR
D- Configure the area range command on the ABR

Q2-You want the devices on your network to summarize routes between OSPF. Which action must you take?
A- Configure the summary-address command on the ASBR
B- Configure the summary-address command on ABR
C- Configure the area range command on the ASBR
D- Configure the area range command on the ABR

Ans1: A
Ans2: D

Referance: http://www.ciscopress.com/articles/article.asp?p=2294214&seqNum=3

@ Anonymous

how did you work out answer B? can you please explain?

Thanks Murti, these two choices make sense.

Hey guys,

Unfortunately I failed today with 6XX points. I got surprised by massive amounts of questions about NAT64 and EVN. Other topics where CEF, Frame Relay, AAA and DHCPv6.

Labs were about configuring OSPF virtual-link on the correct routers, enabling EIGRP, configuring OSPFv3 and Metric calculations.

I’ll be going straight for the ENCOR exam now because it makes no sense to do ROUTE SWITCH and TSHOOT before 24th.

Guys what is MPQ, NUQ5 & 6. and how I can get them?? please help!!

@Anonymous and @FIRE-Roxy

Thanks for your feedback

Which dump did you use ???

RamZ,

If this question is same as you had in your exam, what did you select for your answer?

Or anyone in forum has any knowledge on this topic to confirm the correct answer for this?

Exhibit
R1 (Config)# router eigrp 45
R1 (Config-router)# network 10.0.0.0
R1 (Config-router)# Variance 2
R1 (Config-router)# maximum path 4
Refer to the exhibit Currently, there is at least one route to the 10 0 0 0/8 network with a metric of 10 Which statement describes the outcome of applying this configuration?
A- The router performs only equal-cost load balancing on paths with metric greater than 2
B- If there is one path with metric of 10 and one path with metric of 20, two total paths are used
C- If there are two paths with metric of 10 and two paths with metric of 20, two total paths are used.
D- The first four paths with a metric less than 20 are added to the routing table

@ekva

I haven’t really used a dump (it’s new to me) I learn from the Cisco press book and try to gather some more information from this site and CBT nuggets. Apparently I need to spend more time on this site.

yes, and you need membership account to have all exam question and Sims

Just passed 888. Thank God hahaha, now gotta pay it forward

so the questions here are legit, I had the EIGRP SIM, OSPF stub (the process ID and IPs were different) they emphasized using different Process ID. and Virtual Links IPV6

I can’t remember all drag and Drop: AAA one (resource, auth proxy) frame relaxy point to multipoint, COPP and something else

a few IPSLA questions, definitely know your ports, there were three questions about ACL blocking port whatever

The config labs and sims were practically immediately in the test, by the time i was done i still had like 30 questions to do.

How i studied:

i watched Chris Bryant videos first before even looking at all these questions. I installed GNS3 on laptop and threw together all the network topologies here on the site for practice. When studying the questions, if i didn’t understand the answer i read about it. Make sure you know the concepts and not just memorize answers and you’ll do fine.

Rock out!!!

@AKA

If this question is same as you had in your exam, what did you select for your answer?
– Yes. Exactly same question and I’m not sure 100% but I selected B. because Variance is a number , multiplied by the local best metric then includes the routes with the lesser or equal metric.

C. Incorrect (Should be total 4 paths)
D. Incorrect (Should be “less or equal 20”)

Another question about iBGP about redistributing iBGP routes into OSPF. Answers were like,

A. use “redistribute bgp” in global configuration mode
B. use “bgp redistribute-internal” under ospf routing process
C. use “bgp redistribute-internal” under ospf and bgp routing processes
D. use “bgp redistribute-internal” under bgp routing process

P.S. OSPF sim (Difference Area (42), Process ID (26) , IP 196.168.6.4/30 ) <<<< Sorry for my typo , IP address is 192.168.6.4/30

Wow how could you remember all these questions from Exam?

Hey Guys,

I passed today at the second attempt!
I had the exact same exam that Joe had in the comments above.

There was a new drag and drop for AAA not seen in any of the questions its a new one and it was about AAA commands some of the options were EXEC, Proxy and Network. Also there were a few questions on DHCPV6 mainly SLAAC know this as there were 3-4 questions on it.
also they have changed the wording on some of the drag and drops but it is mainly the same thing, dont let it catch you out that you panic.

so guys i found even with premium access that you still need to know your shit. it helps but it will not be a definite pass.

@Victor & @Joe
THank u for the feedback guys.
The EIGRP sim u referring to, is it EIGRP Eval?

it’s the one that has like 6 routers connected together where you aren’t making config changes and just using show commands. You do a couple sh runns, and Sh ip eigrp topology to find the answers.

Hello peeps,

I passed today with a 790 by the “skin of my teeth”

The sims and drag n drops are the same ones with mods so if you know the why your doing stuff will be fine. That have been posted lately but lots of IPv6 questions. And DHCP options need to know which option does what a couple of questions on this that almost threw me.

Good luck

I pass the exam two days ago with 9XX
The dump still valid.
As I remember 2 or 3 question new or different from the dump.
Good luck and thank you to digitaltut..

Hi, pass TODAY 9xx, lab ospf and emigrò stub, sub the same, ospf chance game and ip but stilo the same.
Have many d&d snmp,access list frame relay ETC… question are in the site but change the question,
Remember dhcp helper, a question nave 3 answer seems the same but only of have smart relay configure, you can have another interface if first fail good luck

Passed one week ago, 55Q
For sim: Ospfv3 virtual link sim, Ospf stub sim, Eigrp evaluation sim.
Dnd: Tacacs+/Radius; Nat64; frame relay, can’t remember the rest.
Some questions about:
-EVN/VRF;
-Stateful Nat64;
-SNMp trap/inform;
-Icmp redirect;
-NAT extendable;
-DMVPN;
-Unicast flooding.
-PPPoE client

Study the labs and all the questions topics, thanks digitaltut and good luck.

Passed 9xx

New to me:
RIP – Topology: Left R1 —^ up R2 ^– Right R3
Which offset-list should be used ai R1 will prefer routes from R3 to go to R2
a) offset-list on R1 in (some value)
b) offset-list on R2 out (some value)
in short where this offset-list should be placed in this topology so R1 will prefer R3 going out to R2

Two BGP neighbors are in a group called PEER-1. Router with Router ID 2.2.2.2 receives a “badauth” message from neighbor 3.3.3.3 how to fix the adjacency

Available on this site:
Sime: Eigrp evaluation, ospfv3 virtual-link, ospf Stub
DD : LMI, AAA (what accounting, authorization and authentication do), FrameRelay (global addressing, address registration), NAT64
good luck!

Passed on 31st Jan.

-The Oct dump is still valid though some few new question i had never seen before(Cant remember)

Labs

-EIGRP Evaluation Sim – Same everything
-IPv6 OSPF Virtual Link Sim – Same
-OSPF Sim – Different IP address (192.168.9.5/30 & 192.168.9.6/30, network address becomes 192.168.9.4, use this on both routers. Full command will be: network 192.168.9.4 0.0.0.3 area 44), OSPF process ID (84), Area (44). You should be able to ping loopback of Lynaic Router from router Portland. The router names have also changed.

DND
AAA (Authentication, Authorization, Accounting) MPQ Q92,
AAA (if authenticated, none, local, krb5-instance, group radius, group tacas+) MPQ Q 93

Thats all i can remember. I didn’t have a premium account. Just read the PDF. Can be found https://www.mediafire.com/file/iz5cctgyhjt2qn1/ROUTE_Oct_2019.pdf

Hi, i will be having exam in two weeks time.
Pls can someone send me or tell me the link to get MPQ and NUQ5 and NUQ6.

adesua1931

adesua 1931 at jii mail

Hi, i will be having exam in two weeks time.
Pls can someone send me or tell me the link to get MPQ and NUQ5 and NUQ6.

adesua1931 at jii maaaail.com

https://www.mediafire.com/file/iz5cctgyhjt2qn1/ROUTE_Oct_2019.pdf

any website help for ccdp?

Hello All,

I’ll be taking the exam this Friday. Is NUQ5, NUQ6 and MPQ still valid?

@Hello All, please share NUQ5, NUQ6 and MPQ

hi if you pass the route exam only does that migrate over to the new ccnp?

thanks

guys,
a quick question, is this the ospf stub sim:
digitaltut . com/route-ospf-sim

hi all, I passed yesterday w 87x

55 Q mostly from MPQ, NUQ 5&6 but I see many question from Composite Q, so study all seccion and you will be ok.

3 -5 new Q that I have never seen before.

SIM: Ospfv3 VL (same) I cannot do ping test, only see the Loopback 4 in the routing table of R1, OSPF stub (with different area and IP and process), EIGRP eval (same).

D&D: AAA (Q92 MPQ), AAA (Q93 MPQ), AAA (Q206 MPQ)

My ROUTE Membership expires 02/13/20, so if you are interesting send me a email yastongrafiti hot mail com

Thanks to digital they were good times studying, see you in tshoot.

Passed yesterday, 9xx

55 q from MPQ NUQ, 3 or 4 DND, around 5 new questions,
Labs: Virtual-link, OSPF Stub Sim, Eigrp Eval.

Premium account really helps.
Good luck

Is it enough to use the Oct questions which can be got from m FAQS? Or you need premium membership?

@monstor
You need to pass all 3 exams

Passed last Friday, 9xx.

Few new questions, mostly from NUQ 5 and 6, and MPQ.

Having time to read (and learn the explanations) of Composite Quizzes and, even better, the entire question list on the right, would be ideal.

Don´t just memorise the answer. Learn them.

Premium account worth the few extra money spent.

Thanks digitaltut, see you again within 3 years to revalidate the Enterprise.

Passed on 31st Jan,2020 8xx.

Labs
EIGRP Evaluation Sim – Same as here
IPv6 OSPF Virtual Link Sim – Same as here
OSPF Sim – Different IP (192.168.9.5 & 192.168.9.6), Process ID (84) & Area (44). Command will be “network 192.168.9.4 0.0.0.3 area 44”. You should be able to ping loopback of router Lynaic from router Portland. The router names have also different.

DND
AAA, (Authentication, Authorization, Accounting) MPQ Q 92
AAA commands ( if authenticated, none, local) MPQ Q 93

Most question from NUQ 5 & 6, and MPQ. ROUTE_Oct_2019 dump still valid.
Few new questions

All the best guys.